Manualios.com

Building Technologies TEL50.GSM General Instructions Manual

Building Technologies TEL50.GSM Manual Online:

3, 2298 votes
Building Technologies TEL50.GSM User Manual
Building Technologies TEL50.GSM User Guide
Building Technologies TEL50.GSM Online Manual

Text of Building Technologies TEL50.GSM User Guide:

  • Building Technologies TEL50.GSM, Building Technologies - 14 - TEL50.GSM 5. Technical data Power supply 10…30 VDC stabilized (230VAC +10 -15% 50-60Hz with supplied power supply) Average consumption In operation: 700mA @ 12VDC On stand-by: 60mA @ 12VDC LED indicator lamps - Power supply present - GSM field present - Status of alarm input - Status of relay outputs (2) Alarm input Potential-free and normally open (factory setting) or normally closed (selectable) Temperature sensor input LG-Ni1000 Measuri

  • Building Technologies TEL50.GSM, Building Technologies - 25 - TEL50.GSM 8. Environmental compatibility and disposal This product has been developed and constructed using materials and processes that take account of environmental issues. Refer to the following notes for disposal of the product at the end of its service life or if it needs to be replaced:  For disposal purposes, this product is classified as an electrical and electronic device: do not dispose of it as household waste especially as far as the printed circuit is concerned.  Comply with all local laws that are in force.  Reuse raw materials as much as possible

  • Building Technologies TEL50.GSM, Building Technologies - 7 - TEL50.GSM 3. General information The TEL50.GSM phone remote control has been designed for remote operation of electrical or electro-hydraulic equipment such as room thermostats, boilers, burners, heaters, zone valves, circulation pumps, irrigation systems, etc. It is particularly suitable for holiday home installations where there is no fixed telephone network. The remote control can only be used through the GSM mobile network. Commands can be sent via the fixed telephone network (DTMF tones) or GSM mobile network (DTMF tones and SMS messages with preset syntax). The TEL5

  • Building Technologies TEL50.GSM, Building Technologies - 17 - TEL50.GSM SMS text SMS reply Action OUT1=1 OUT1=1 closes contact relay 1 OUT1=0 OUT1=0 opens contact relay 1 OUT2=1 OUT2=1 closes contact relay 2 OUT2=0 OUT2=0 opens contact relay 2 OUT1 OUT1=0 or OUT1=1 (*) queries the status of contact relay 1 – OUT1=0 contact open OUT1=1 contact closed OUT2 OUT2=0 or OUT2=1 (*) queries the status of contact relay 2 – OUT2=0 contact open OUT2=1 contact closed IN1 IN1=0 or IN1=1 (*) queries the status of alarm input - IN1=0 contact open IN1=1 contact closed (*) Note: with factory settings enabled. See “digital I/O states” chapter. 6.3 Tempe

  • Building Technologies TEL50.GSM, Building Technologies - 9 - TEL50.GSM OUT1 - Relay output 1 Potential-free relay contact for control of special devices (boiler, zone valve, heater, etc.). Observe the max current rating of the electrical contacts indicated in the technical data. TEMP - Analog input for connection of an LG-Ni1000 temperature sensor Terminals 1 e 4: not used. Terminals 2 and 3: connect LG-Ni1000 sensor. Terminal 5: connect shielding of sensor cable (earth) + - Power supply input. Only use the supplied power supply. Use of incompatible power supplies may cause irreversible damage to the device

  • Building Technologies - 8 - TEL50.GSM 4. Installation Comply with the permitted temperature and humidity conditions (see Technical Data). 4.1 Wall-mounting Mount the device on the wall or 3-module flush-mounted box (503 type) using the special holes in the rear part of the container. During installation, be careful not to damage the internal co

  • Building Technologies TEL50.GSM, Building Technologies - 1 - TEL50.GSM en English 1. Introduction Thank you for choosing this product. Please read this manual carefully to optimize use of the TEL50.GSM. 1.1 Copyright Siemens S.p.A. All rights reserved. The reproduction, modification or transcription of this document without prior written authorization is forbidden except as allowed under the copyright laws. Copyright© 2005 1.2 Trademarks TEL50.GSM is a Siemens S.p.A. registered trademark.

  • Building Technologies TEL50.GSM, Building Technologies - 2 - TEL50.GSM 1.3 Declaration of conformity Siemens S.p.A. Building Technologies Viale Piero ed Alberto Pirelli, 10 - 20126 Milano (MI) Italy declares on its sole responsibility that the following product: TEL50.GSM complies with the regulations in force with reference to the R&TTE 99/5/EC directive and, above all, with the following standards: Health and Safety (Art. 3.1 a) EN 60950:2000 EMC (Art. 3.1 b) EN 301489-7 v1.1.1 (09/2000) RF spectrum efficiency (Art. 3.2) EN 301419-1 v4.1.1 (03/2000) incl. EN 301511 v7.0.1 (12/2000)

  • Building Technologies TEL50.GSM, Building Technologies - 6 - TEL50.GSM 2.2 Operating instructions 1. The SIM Card must always be inserted and removed when there is no power supply. If not, the SIM Card read interface inside the GSM module could be damaged. 2. Always disable the PIN code of the SIM card. If not, the TEL50.GSM cannot operate. Delete from SIM card all lists of SMS (inbox, outbox, sent items) and disable all additional services (answering service, call forwarding, etc). Do this using a normal mobile phone. SIM card (non included) could be for voice traffic only. However we recommend using SIM cards that are also enable

  • Building Technologies TEL50.GSM, Building Technologies - 10 - TEL50.GSM 230 V AC CI L N + - N1 T1 T2 OUT 2 TEMP IN 1 OUT 1 S1 L L1 L1 M L N + - Alim. TEL50.GSM REV.... Legend Alim = Stabilized power supply 230/12VDC 1A CI = TEL50.GSM telephone remote control N1= REV.. Room thermostat or other electric equipment B1 = LG-Ni1000 temperature sensor (or termination resistor) S1= Potential free generic alarm contact L1 = Electrical device to be activated E1 = Boiler M1 = Circulation pump V1 = Zone valve E1 V1 M1 B1 1 2 3 4 5

  • Building Technologies TEL50.GSM, Building Technologies - 15 - TEL50.GSM 6. Basic configuration With the factory configuration, the TEL50.GSM can already handle the following voice (DTMF tones) and SMS commands. In order to operate safely and correctly, the device must be correctly connected to the GSM network (see par. 4.6). Carefully check that this is the case during installation and before leaving the device’s final location. 6.1 Commands via DTMF tones Ensure that the calling telephone is enabled to send DTMF tones (multifrequency). Almost all phones currently on sale (both for fixed network and mobiles) have this option. Make sure that the keypad has been

  • Building Technologies TEL50.GSM, Building Technologies - 3 - TEL50.GSM 1.4 Warranty This product is guaranteed against any material and manufacture defects. SIEMENS reserves the right, at its own discretion, to repair or replace faulty products. The warranty is deemed null and void if the fault is caused by improper use or by an operating procedure that is not included in this manual. The warranty will not cover faults caused by: • improper and careless use • damage caused by atmospheric agents • acts of vandalism • material that is subject to wear and tear 1.5 Con

  • Building Technologies TEL50.GSM, Building Technologies - 23 - TEL50.GSM Example: SMS command SMS reply Action 5 6 allarme temp. ON OFF impostazione di fabbrica TEMP ALARM=5 ALARM=5 alarm threshold set to 5°C TEMP RESET=6 RESET=6 reset threshold set to 6°C SMS command SMS reply Action 19 20 allarme temp. ON OFF TEMP ALARM=20 ALARM=20 alarm threshold set to 20°C TEMP RESET=19 RESET=19 reset threshold set to 19°C Alarm notification is automatically enabled when the ALARM and RESET thresholds are set. The identification string of the analogue input can be modified if necessary: SMS command SMS reply Action ALIAS ANALOG=TEMPEXT ANALOG=TEMPE

  • Building Technologies - 12 - TEL50.GSM Recommendations for use of fixed or external antenna You are advised to observe the following recommendations: • The antenna must be placed at least 2m from any electronic equipment, at least 15cm from any obstacles and in a position where there is good reception. • If malfunctioning or interference to the l

  • Building Technologies - 22 - TEL50.GSM 7.3 Alarm notification enabling The TEL50.GSM can handle the following alarms: - Contact IN1 closed alarm - Temperature threshold exceeded alarm 7.3.1 IN1 closed alarm This alarm may come from any device whose status needs to be monitored (eg. home alarm system, boiler burner block, etc.). A potential-free contact must be u

  • Building Technologies TEL50.GSM, Building Technologies - 19 - TEL50.GSM [USER] command examples SMS command SMS reply Action USER USER01=3351234567.1 USER01=3351234567.1 User USER01 set as Administrator USER USER02=3471234567.2 USER02=3471234567.2 User USER02 set as User USER USER03=3291234567.3 USER03=3291234567.3 User USER03 set as Notify USER USER20=3201234567 USER20=3201234567 User 20 set as Notify USER USER01 USER01=3351234567.1 queries USER01 position USER USER05 USER05 deleted queries USER05 position (no number present) USER USER01= USER01 deleted cancels USER01 position USER 3351234567= USERxx deleted cancels the User number 3351234567 from position xx The USER

  • Building Technologies TEL50.GSM, Building Technologies - 18 - TEL50.GSM 7. Extended configuration Using the basic configuration already present, the user can customize device parametrization by changing some of the system parameters via SMS. Carefully note any changes made and keep them with these instructions in order to ensure that the device is correctly controlled even after a long period of time or by other qualified users. 7.1 Creation of a qualified user list All the telephone numbers of users (both fixed and mobile), up to a ma

  • Building Technologies TEL50.GSM, Building Technologies - 5 - TEL50.GSM Precautions: Do not install and use the product in close proximity to electromedical equipment without checking that this is permitted. During operating, the product may cause interference to transceiver equipment such as televisions, radios, PCs. Move the product so that there is no more interference. Hearing aids or pacemakers or other personal medical devices may be subjected to interference when the device is in operation. Consult your doctor for further information. Dispose of the product and accessories at the end of their service life in accordance with regulations. T

  • Building Technologies TEL50.GSM, Building Technologies - 26 - TEL50.GSM Siemens A.E. Electrotechnical Projects & Products Infrastructure & Cities Sector Building Technologies Division Control Products and Systems Agisilaou Str. 6 - 8 GR - 151 23 Athens, Greece Building Technologies Greece internet: http://www.siemens.gr/buildingtechnologies Product information on internet: http://www.siemens.com/hit-gr

  • Building Technologies TEL50.GSM, Building Technologies - 13 - TEL50.GSM 4.6 Checking of indicator lamps The TEL50.GSM has 5 LED indicator lamps. Three of these can be seen on the front of the device and the other two are located in the lower part and can be seen through the plastic grid. LEDs On Off OUT1 (red) contact closed contact open OUT2 (red) contact closed contact open IN1 alarm (red) contact closed contact open power supply (green) power supply present no powe

  • Building Technologies - 20 - TEL50.GSM 7.2 Modification of Input-Output identification string In this section the User can modify the identification string (ALIAS) for the device inputs/outputs. New identification strings will support the factory’s ones that remain active. Queries or commands can be sent using either factory’s strings or ALIAS set by the user. If no changes are

  • Building Technologies TEL50.GSM, Building Technologies - 16 - TEL50.GSM When the “#” tone is received, if the command is effected, the sequence of corresponding beeps (ON or OFF) is generated. If the command is not recognized or is not applicable (for example, if an ON command is sent to an input “31#”), the ERROR tone is generated. If the “  ” tone is received, the OFF tone is generated as confirmation of the command. Call the telephone number for the TEL50.GSM and wait for the device to answer (a beep after the first ring). Dial the command you require from those ava

  • Building Technologies TEL50.GSM, Building Technologies - 11 - TEL50.GSM 4.3 Connection of stilo antenna The TEL50.GSM is supplied with its own dual band stilo antenna with the following characteristics: PARAMETER CHARACTERISTICS Profile Dual-Band GSM 900MHz band 890-960MHz 1,800MHz band 1710-1,880MHz Impedance 50 ohm WSVR <= 1:1,5 Type Omnidirectional Radiation diagram on horizontal plane Circular @ ± 0.5dB Radiation diagram on vertical plane ± 35° @ 3dB Connector SMA (male) 4.4 Connection of external antenna (optional) In the top part of the T

  • Building Technologies TEL50.GSM, Building Technologies - 4 - TEL50.GSM 2. Instructions In order to use the product safely and efficiently, please read the following instructions carefully before use. The product may only be employed for the use for which it has been conceived and manufactured. Any other use shall be considered the user’s sole responsibility. 2.1 Safety instructions Installation, programming and commissioning should only be carried out by qualified operators; these operators must be physically

  • Building Technologies TEL50.GSM, Building Technologies i TEL50.GSM en English 1. INTRODUCTION ............................................................ 1 1.1 Copyright ................................................................ 1 1.2 Trademarks ............................................................ 1 1.3 Declaration of conformity ....................................... 2 1.4 W arranty................................................................. 3 1.5 Contents of sales pack........................................... 3 2. INSTRUCTIONS ............................................................ 4 2.1 Safety instructions ....................................

Related Products and Documents (Modem):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Canon T90 Instructions manual canon/t90-G38.pdf 25 Mar 2024 128 5.47 Mb
2 Palm Treo 700P smartphone Operation & user’s manual palm/treo-700p-smartphone-6I8.pdf 14 Oct 2023 204
3 Medion MD 85173 Instruction manual medion/md-85173-LXL.pdf 26 May 2023 42
4 Sony HAW-EIBU Installation manual sony/haw-eibu-J16.pdf 15 Oct 2022 60
5 Vaillant HOME COMBI 25 - A (H-GB) Operating instructions manual vaillant/home-combi-25-a-h-gb-1II.pdf 22 Aug 2023 20
6 Electro-Voice PS8 Brochure & specs electro-voice/ps8-Z8T.pdf 06 Jan 2024 2 0.61 Mb

Similar Resources:

  • Toshiba

    Satellite M20

    (52 pages)
    RG 5.375 x 8.375 ver 2.3.2Satellite® M20 SeriesResource GuideKeep this guide in a convenient place to access important information about your computer.If you need assistance, use one of the following: ❖ Toshiba Global Support CentreCalling within the United States (800) 457-7777Calling from outside the United States (949) 859-4273 Please fill in for your …
  • NETGEAR

    R6300

    (3 pages)
    DATA SHEETR6300 WiFi Router 802.11ac Dual Band GigabitR6300SPEED WORLD’S FASTEST WIFI—Up to 450+1300‡ Mbps† GIGABIT WIFI—Next generation WiFi now at Gigabit speeds GIGABIT WIRED—Ideal for HD gaming & videoRELIABLE CONNECTIONS SIMULTANEOUS DUAL BAND—Reduces interference for better connections to more WiFi devi …
  • D-Link

    DSL-2740B

    (10 pages)
    D-Link Technical Support – How to use the Setup Disc. Page 1 of 10 Installation Guide using CD ROM for DSL modem routers DSL-2740B (Rev F1) and DSL-2750B (Rev B1) This document details how to configure the DSL-2740B and DSL-2750B using the supplied Setup Disc. …
  • Huawei

    E366

    (9 pages)
    1 Thank you for choosing the Mobile Broadband USB Stick. With your USB Stick, you can access a wireless network at high speed. Note: This manual describes the appearance of the USB St ick, as well as the procedures for preparation, installat ion, and removal. For operation details about the management program, see the online help included in the management p …
  • Billion

    BiPAC 7300

    (2 pages)
    Benefits (802.11g) ADSL2+ Firewall Routerwith EZSO and QoS BiPAC 7300(G) • High speed Internet access with ADSL2/2+; backward compatible with ADSL• 802.11g Wireless AP with WPA-PSK/WPA2-PSK Support (BiPAC 7300G)• SOHO Firewall Security with DoS Prevention and SPI• Easy Sign-On (EZSO) and Web-based Conf …
  • Zoom

    1086 Series

    (2 pages)
    Zoom We3G Modem Quick Start This Quick Start describes how to use the Zoom We3G Modem with any Windows 7, Vista, or XP (SP2 and above) computer and with a Macintosh computer with OS X 10.4.9 or above. Before You Begin Before you can connect to the Internet with your new modem, you must: 1 Sign up for a mobile broadband service plan. 2 Slide the servi …

Comments, Questions and Opinions: