Calandra Racing Concepts WTF1 Assembly Manual
|
Calandra Racing Concepts WTF1, 3254 - 2-56 Button Head 40194 - Hard Anodized Alum Pivot ball 12772 - 4-40 Thin Hex Nut 1430 - 4-40 x ½” Flat Head 1209 - Washer *Note - Sometimes it is helpful to over-tighten the top clamp screws, then work the ball around by hand, and then loosen the screws so the ball floats around very free. Do not over-tighten the screws too much or you could warp the pivot socket. slightly 1412 - Red Locknut Bag 1 Center Pivot 1 3374 - Center Pivot Socket Bag 1 Center Pivot 1555 - WTF-1 Chassis Plate 3374 1555
Calandra Racing Concepts WTF1, 1426 - 4-40 x 5/16” Flat Head 1430 - 4-40 x ½” Flat Head One-Piece Side Links 13615 - Red Low- Profile Ball *NOTE - Before installing, inspect the side links and you will notice that the screw holes on one side of the link are larger than the holes on the other side. Before popping the links on the balls, be sure that the larger hole faces toward the outside of the chassis. Slide the 2-56 button head screws through the large holes in the outside of the side links, and then thread them into the small inner holes as shown in the illustration. Do n
Calandra Racing Concepts WTF1, 3440 - Motor Plate 1574 - Graphite X-brace 3 1424 - 4-40 x 1/4” Flat Head 3442 - Left Side Pod Plate Bag 3 Slider Pod 33411 - Slider Bearing Carrier 1574 1436 - 4-40 x 3/8” Button Head 13615 - Red Low- Profile Ball Bag 4 Tweak Plate 1570 - Tweak Plate 1570 1435 - 4-40 x 7/16” Button Head 33411 3288 - 4-40 x 3/8” set screw 3387 - Molded Plastic Spring Holder Thread the set screw in until flush with the bottom of the holder. 1791 - Pro Tapered Springs .45mm 3375 - Molded ½” Standoffs (4) 3375 Make sure spring coil is seated into groove on spring holder. 3375 3375 - Molded ½” Standoffs (4)
4 Bag 4 1434 - 4-40 x 1/4” Button Head 1565 - WTF-1 Rear Top Plate 1565 Top Plate 1407 - Anodized Hex Balls (4) 1384 - 2-56 Steel Ballstuds & Cups for Damper tubes (4) 1384 1407 1397 - 2-56 set- screw stud 1384 - 2-56 Steel Ballstud & Plastic Ball Cup 32694 - Short 4-40 Plastic Ball Cup (on tree) 13695 - .035” Allen Driver 32693 - Delrin Plunger 32691 - Alum
Calandra Racing Concepts WTF1, 5 1854 - Top Deck - Gen-X10 SE Bag 6 Top Deck 1424 - 4-40 x 1/4” Flat Head 1434 - 4-40 x 1/4” Button Head 3373 - Plastic Battery Position Pieces 1537 - Hex Standoff - WTF-1 Top Deck 1854 1537 3378 3373 1407 1407 - Anodized Hex Balls (4) 3378 - Body Posts w/ collars (1 in.) ** Adding the Damper Tubes to the Chassis assembly ** Snap the assembled & lubed damper tubes on the respective points as shown in the diagram to the right. You will find it easier to snap on the smaller 2-56 ball studs first, then pop the lower, larger 4-40 ballcups on. Bag 5 Damper Tubes continued... The 3378 1” Body Post pictured in this assembly is used as an antenna mounting post. Most all antenn
Calandra Racing Concepts WTF1, 6 2.510” 1 - Thread the spring adjuster nut onto the shock body as shown. *This needs to be installed first or you will not be able to get it on later after the lower endof the shock is assembled!* 2 - Insert only 1 of the small o-rings into the lower end of the shock body. Next, install the bottom shock plug and tighten the bottom shock cap. 3 - Insert 1 of the small e-clips into the lower groove of the shock shaft. Slide the piston over the shaft until it stops against the e-clip and then secure it in place with the other e-clip in the end groove. 4 - Put a small dab of the included shock oil on the threads of the shock shaft to
Front End Lip Bag F 33461 3221 7 1540 1546 1540 - Front End Plate - F1 1546 - F1 Lower Arm Pivot Ball 1434 - 4-40 x 1/4” Button Head 13615 - Red Low- Profile Ball 1412 - Red Locknut 3234 - Brass Set Screw 3391 - .45mm Front Spring 3228 - CRC King Pin - Long 1:10 3221 - Steering Block Set 1535 - F1 Steel Stub Axle 1535 3391 3228 1382 - E-Clip Front End Bag F 1490 - M3 x 8mm Butto
Calandra Racing Concepts WTF1, Front End - continued... 1.192” 1553 8 1544 1544 - F1 Upper Arm / Steering Block Ball 3221 - Steering Block Set 1582 - E-Clip for Upper Hinge Pin 13615 - Red Low- Profile Ball 1424 - 4-40 x 1/4” Flat Head 1436 - 4-40 x 3/8” Button Head 3221 Bag F 1499 - M4 Locknut 1496 - M4 x 30mm Front End Screw 1496 3355 - Alum Vertical Mount Set-Red 3355 1553 - Graphite Servo Mount Plate-F1 (Servo Tape - Not Included) 1545 - F1 Upper Hinge Pin 1545 3376 - Molded Servo Saver Brace 3376 Front End - continued... Bag F 1542 1542 - F1 Upper Ar
Calandra Racing Concepts WTF1, 4201 - Diff Ring 1387 - 1/4” x 3/8” Plain Bearing Lip 4121 - Diff Spacer 4123 - Spring Washer 1-INSTALL AND GREASE THE DIFF BALLS Place the spur gear flat on the table in front of you with the side that says “CRC” facing down. The diff balls will fall into each of the outer ring of holes in the diff gear, but won’t fall out the other side. Place a small dab of silicone diff grease on each ball to lube the ball and prevent the balls from falling back out of the holes during assembly. Use very little! *(Holding the car on i
Calandra Racing Concepts WTF1, 13783 - 4-40 x 1/8” Set Screw 10 1436 - 4-40 x 3/8” Button Head 1378 Bag 10 Bag 11 1378 - Body Posts w/ collars (2 in.) 3378 - Body Posts w/ collars (1 in.) 1 piece of 3378 will mount to the front wing (not included) once it is installed. 1499 - M4 Locknut 1529 - 5mm Plastic Spacer - F1 Fr Axle 1532 - Thin #8 Washer - F1 Rr Wheel 1549-5x10mm Unflanged Bearing 4735 - 5mm Shim 4735 1529 1532 The 2 pieces of 3/8” Button Head screws contained in this bag are for mounting the rear wing to the plastic standoff posts on t
Model Tech Blue Max Toy Assembly instructions manual
Blue Max |
Tiger Electronics Bob the Builder Counting Hammer Toy Instructions
Bob the Builder Counting Hammer |
REVELL Fokker D VII Toy Assembly manual
Fokker D VII |
RO Aerodyne 700 scale fuselage MD500 Toy Instruction manual
700 scale fuselage MD500 |
Lionel 464R Sawmill Toy Owner's manual
464R Sawmill |
THUNDER TIGER Raptor E300 md Toy Instruction manual
Raptor E300 md |
Elite Models aviator pro 120 Toy Instruction manual
aviator pro 120 |
Goblin Goblin 770 Sport Toy Manual
Goblin 770 Sport |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Fein | MShy649-1 | Operation & user’s manual | fein/mshy649-1-A2F.pdf | 08 May 2023 | 96 | 7.53 Mb |
2 | Campbell | SDS-122 | Instruction manual | campbell/sds-122-P6L.pdf | 02 Aug 2022 | 14 | 0.11 Mb |
3 | Cisco | NME-16ES | Product support bulletin | cisco/nme-16es-55F.pdf | 27 Feb 2023 | 5 | 0.05 Mb |
4 | Mitsubishi Electric | HC1100 | Operation & user’s manual | mitsubishi/hc1100-U2D.pdf | 09 Feb 2023 | 39 | |
5 | Sony | LMD-2451TD | Specifications | sony/lmd-2451td-441.pdf | 22 Jul 2023 | 2 | 0.67 Mb |
6 | Sony | BDV-N890W | Specifications | sony/bdv-n890w-KP8.pdf | 09 Feb 2023 | 5 | 0.22 Mb |
Force RC
145Install battery cover. Push Power switch to ON.FullyChargedInstallAA batteries6Open ground target lid.9When finished, push Power switch to OFFPush in lock and remove battery cover.32218After severalseconds Explosionssound.Fly helicopter and fire onGround Target, or defend it from an opponent. When target is attacked, light and sound show the hits. LED F …
Ground Target(12 pages) |
Faller
Sa. Nr. 105 243 0LOKSCHUPPEN, 2-STÄNDIGTWO-STALL ENGINE SHED REMISE À LOCOMOTIVES, 2 PLACES LOCLOODS VOOR 2 SPORENArt. Nr. 120165Inhalt Spritzlinge Contents Sprues Contenu Moulages Inhoud Gietstukken12x21x31x41x51x62x71x81x92x101x111xMachen Sie sich bitte vor Beginn des Bastelns mit dem Bausatzinhalt und der Anleitung vertraut und prüfen Sie die Vollstän …
120165(12 pages) |
Kayoba
002-565Instrukcja obsługi (Tłumaczenie oryginalnej instrukcji) Ważny! Przed użyciem uważnie przeczytaj instrukcję obsługi! Zachowaj ją naprzyszłość.KARABIN NA PIŁKI PIANKOWEPLBruksanvisning i originalViktigt! Läs bruksanvisningen noggrant innan användning! Spara den för framtida behov. SKUMBOLLSGEVÄRSEENFOAM BALL GUNOperating instructions …
002-565(8 pages) |
ROBBE
Building and Operating InstructionsArcus E 2.2 ARF No. 2568Notice de montage et de mise en œuvreArcus E 2.2 ARF Réf. 2568Istruzioni di montaggio e d’uso Arcus E 2.2 ARF N. 2568Manual de construcción y de usoArcus E 2.2 ARF Nº 2568 Návod ke stavbě a provozuArcus E 2.2 ARF č. 2568
…
Arcus E 2.2 ARF(32 pages) |
Stevens Aero Model
eHopperBy Stevens AeroModelSpan 33.5 inches | Length 21.5 inches | Wing Area 235 inches2 | Flying Weight 4.5 - 5.5 oz.Version 02/02//2010eHopperTM © 2009 Stevens AeroModel all rights reserved. Page 1 of 36
…
eHopper(35 pages) |
BMI
Valbella 2000 BMI # 11620 Manual WARNING - THIS IS NOT A TOY! Radio controlled model aircraft are capable of inflicting serious injury and/or property damage if not assembled, operated and maintained in a competent and safe manner. The successful assembly, operation and maintenance of radio controlled model aircraft are not intuitive skills a …
Valbella 2000(14 pages) |
Clarke Scrubber FOCUS L17Guide: Clarke FOCUS L17 (7CKA43, Upd.07/01/2024) FOCUS L17, 142 |
andrews Water Heater CWH30/200Water Heater PDF Installation, operation and maintenance manual CWH30/200, 44 |
SVA Monitor 506BMonitor Specifications (SVA 506B) 506B, 2 |
Haier Air Conditioner HM-05CC03/R1HM-05CC03/R1 Service manual - 916V1D HM-05CC03/R1, 43 |
Adobe Other NOVAPDF PROFESSIONAL - VERSION 7Adobe NOVAPDF PROFESSIONAL - VERSION 7 Manual (Doc Type: Other Manual ) NOVAPDF PROFESSIONAL - VERSION 7, 122 |
Allen-Bradley Measuring Instruments 1444-TSCX02-02RB#CREL14: 1444-TSCX02-02RB Measuring Instruments Operation & user’s manual 1444-TSCX02-02RB, 550 |
Grizzly Saw G0501Saw PDF Instruction manual G0501, 109 |
Husky Mounts Racks & Stands TL-400LMRacks & Stands #8BP372 TL-400LM, 4 |
Turtle Beach Headphone Ear Force XL1Ear Force XL1 (Headphone ePDF User Guide, #P6X1PH) Ear Force XL1, 7 |
Vogue Kitchen Appliances 356132Kitchen Appliances #WPHGL9 356132, 10 |
Hunter Fan 21317Hunter 21317 User Guide (Doc Type: Fan Parts manual) 21317, 2 |
LG Washer/Dryer WD-3274RHDWD-3274RHD (Washer/Dryer ePDF User Manual, #B5V166) WD-3274RHD, 28 |