Manualios.com

Carl Valentin PICA II Operating Manual

Carl Valentin PICA II Manual Online:

3.65, 2774 votes
Carl Valentin PICA II User Manual
Carl Valentin PICA II User Guide
Carl Valentin PICA II Online Manual

Text of Carl Valentin PICA II User Guide:

  • Maintenance and Cleaning Pica II Series 50 Operating Manual 10.15 9.4 Cleaning the Label Photocell CAUTION! Label photocell can be damaged!  Do not use sharp or hard objects or solvents to clean the label photocell. The label photocell can become dirtied with paper dust and this can adversely affect label detection. Figure 15 1. Open printer cove

  • Pica II Series Error Correction 10.15 Operating Manual 57 Error message Cause Remedy 71 Invalid page As page number either 0 or a number > 9 is selected. Select a number between 1 and 9. 72 Page selection A page which is not available is selected. Check the defined pages. 73 Page not defined The page is not defined. Check the print definition. 74 Format user guiding W

  • Carl Valentin PICA II, Pica II Series Control Panel 10.15 Operating Manual 37 State Key Description/Function Not ready Change to the online mode. Short press = Label feed. Longer press = Single cut. Short press = Test print. Longer press = Status print. + Keep the keys together pressed to access the service functions (page 43). Printing Interrupt print order. Continue print order. Pause Interrupt print order. Continue print order. Error Error acknowledgement (see table on page 53).

  • Carl Valentin PICA II, Installation Pica II Series 24 Operating Manual 10.15 4.2 Connecting the Label Printer The label printer is equipped with an universal AC adaptor and is operated according to standard with nominal voltage of 230 V. The conversion to 115 V is only allowed by trained personnel. CAUTION! The label printer can be damaged by undefined switch-on currents.  Set de power switch to '0' before plugging in the label printer.  Insert power cable into power connection socket.  Insert plug of power cable into a grounded e

  • Carl Valentin PICA II, Index Pica II Serie 62 Operating Manual 10.15 Printer key functions ............................................................................. 36, 37 states ........................................................................................ 35, 36 Printhead adjusting ......................................................................................... 53 parallelism, adjusting ...................................................................... 54 pressure, adjusting ......................................................................... 54 replacing ..........

  • Carl Valentin PICA II, Technical Data Pica II Series 16 Operating Manual 10.15 3.1 Control Inputs and Outputs By means of a maximum of 16 control inputs and outputs which, in the following, are also referred to as ports, different functions of the printer system can be triggered and operating states can be displayed. The ports are provided by means of a D-Sub bushing (26pin HD) at the rear panel of the printer system and are galvanically isolated from protective earth (PE) by means of an optocoupler semi-conductor route. Each port can be configured as input and as output. This function however, is predefined in the printer

  • Carl Valentin PICA II, Pica II Series Service Functions 10.15 Operating Manual 45 Press key to arrive the next menu. Zero point adjustment in Y direction Indication of value in 1/100 mm. After replacing the printhead - the print cannot be continued at the same position on the label, the difference can be corrected across the printing direction. NOTICE! The value for zero point adjustment is set ex works. After replacing the printhead, only service personnel are allowed to set this value anew. Press key to arrive the next menu. Select Printer Type Press keys + or + to change the printer type. Press key to confirm the selection

  • Pica II Series Technical Data 10.15 Operating Manual 15  Tear-Off Edge  Real time clock with printout date and time Automatic daylight saving time Storage of data with shut-down  Integrated Rewinder (max. outside diameter 180 mm  Thermal Direct or Thermal Transfer Version  USB Interface  Windows Printer Driver on CD ROM  Labelstar Office Lite on CD RO

  • Pica II Series Maintenance and Cleaning 10.15 Operating Manual 47 9 Maintenance and Cleaning DANGER! Risk of death by electric shock!  Disconnect the label printer from power supply before performing any maintenance work. NOTICE! When cleaning the label printer, personal protective equipment such as safety goggles and gloves are recommended. Maintenance

  • Carl Valentin PICA II, Pica II Series Safety Instructions 10.15 Operating Manual 9 The installation of the power supply to connect our printers has to be effected according to the international rules and regulations, especially the recommendations of one of the three following commissions:  International Electronic Commission (IEC)  European Committee for Electro technical Standardisation (CENELEC)  Verband Deutscher Elektrotechniker (VDE) Our printers are constructed according to VDE and have t

  • Carl Valentin PICA II, Pica II Series Technical Data 10.15 Operating Manual 21 3.2 Plug & Play Plug & Play capable printers can be recognised automatically at parallel ports, USB-IEEE 1394- or infra-red connections but the last both are not important for our printers. The following table shows the Plug & Play capability of the different operating systems. Interface Windows 95 98 Me NT4 2000 XP Vista 7 LPT Support Recognition by Boot Procedure, Dev. Manager Installation USB Support s.b. Recognition by Hot Plug & Play s.b. Hot Plug & Play The table above shows that USB provides the recognition during the

  • Carl Valentin PICA II, Pica II Series Safety Instructions 10.15 Operating Manual 7 2 Safety Instructions The label printer is configured for a voltage of 230 V. It has to be plugged into a grounded socket only. Couple the label printer to devices using extra low voltage only. Before making or undoing connections, switch off all devices involved (computer, printer, accessories etc.). Operate the label printer in a dry environment only and do not get it wet (sprayed water, mist etc.). In case of cleaning and maintenance with an open printer cover, ensure that clothing, hair, jewellery and similar personal items do not contact the exposed rotating parts. The print uni

  • Carl Valentin PICA II, Pica II Series Error Correction 10.15 Operating Manual 55 Error message Cause Remedy 32 System clock Real Time Clock function is selected but the battery is empty. Defective RTC. Change battery. Change RTC component. 33 No CF interface Interrupted connection CPU - CF card. Defective CF card interface. Check connection CPU - CF card interface. Check CF card interface. 34 No print memory No print CF found. Check CF assembly on CPU. 35 Cover open At start of a print order the printhead is open. Cl

  • Carl Valentin PICA II, Pica II Series Printing 10.15 Operating Manual 39 7 Printing CAUTION! Printhead damage caused by improper handling!  Do not touch the underside of the printhead with the fingers or sharp objects.  Ensure that the labels are clean.  Ensure that the label surfaces are smooth. Rough labels act like emery paper and reduce the service life of the printhead.  Print with the lowest possible printhead temperature. 7.1 Processing Print Orders The printer must be in Online mode. During a current print ord

  • Carl Valentin PICA II, Pica II Series Maintenance and Cleaning 10.15 Operating Manual 53 9.7 Adjusting the Printhead Complete the following printhead settings to achieve the best possible print image:  Align the heating line with the highest point of the print roller. Density of the print image is the greatest at this point.  Set the parallelism of horizontal lines with the edge of the label. CAUTION! The printhead assembly can be damaged. Attempting to adjust the printhead when the fixing screw (E) is tight can lead to defects at the print

  • Carl Valentin PICA II, Error Correction Pica II Series 56 Operating Manual 10.15 Error message Cause Remedy 51 Internal file error Internal file system error. Please contact your distributor. 52 Root full The max. number (64) of main directory entries is reached. Delete at least one main directory entry and create subdirectories. 53 Drive full Maximum CF capacity is reached. Use new CF Card, delete no longer required files. 54 File/directory exists The selected file/directory already exists. Check name, select a different name. 55 File too large During copying procedure not enough memo

  • Carl Valentin PICA II, Pica II Series Error Correction 10.15 Operating Manual 59 Error message Cause Remedy 108 GS1-128 invalid Transferred GS1-128 bar code is invalid. Verify bar code data (see GS1- 128 bar code specification). 109 EPC parameter Error at EPC calculation. Verify data (see EPC specification). 110 Housing open When starting the print order the housing cover is not closed. Close the housing cover and start the print order anew. 111 EAN.UCC code Transferred EAN.UCC code is invalid. Verify bar code data (see corresponding specification). 112

  • Carl Valentin PICA II, Printing Pica II Series 40 Operating Manual 10.15 7.3 Label Feed The printer must be in Offline mode. Press key to start the feed of one label. 7.4 Saving Labels The saving of data e.g. text or graphic is done in the internal data memory. The saving can be selected either in our label design software or by an appropriate program. For more information, see the appropriate manual. 7.5 Tear-off Mode In order to detach the label band after terminating the print order by hand, the label printer is equipped by default with a tear-off bar.

  • Carl Valentin PICA II, Safety Instructions Pica II Series 10 Operating Manual 10.15 Immunity to interference according to EN 61000-6-2: 2005 industrial sector  Stray radiation against discharge of static electricity according to EN 61000-4-2: 12-2001  Electromagnetic fields according to EN 61000-4-3: 11-2003, ENV 50204: 03-1995  Fast transient burst according to EN 61000-4-4: 07-2005  Surge according to EN 61000-4-5: 12-2001  High-frequency tension according to EN 61000-4-6: 12-2001  Voltage interruption and voltage drop according to EN 61000-4-11: 08-2004 NOTICE! This is a machine of type A. T

  • Carl Valentin PICA II, Pica II Series Error Correction 10.15 Operating Manual 53 10 Error Correction In case an error occurred the printer stops and the print order is interrupted. After removing the error, press key to acknowledge the error. An active print order is now interrupted. Press key to print the last printed label once more. This is particularly important if an error arose during a current print order and the sequence of the labels (e.g. counter) is to be considered. Press key to continue a print order or press key to cancel the print order. Error message Cause Remedy 1 Line too high Line rises up completely or partly over the up

  • Carl Valentin PICA II, Pica II Series Installation 10.15 Operating Manual 23 4 Installation  Lift the label printer out of the box.  Check the label printer for transport damages.  Check delivery for completeness.  Label Printer.  Power Cable.  Empty core, mounted on transfer ribbon rewinder.  Tear-off edge (basic printers only).  Dispenser edge (printers with option dispenser only).  Cutter unit (printers with option cutter only).  Documentation.  Printer driver on CD ROM.  Labelstar Office LIT

  • Loading Media Pica II Series 30 Operating Manual 10.15 B J A K F DCE N M H G I Figure 10 1. Open the printer cover. 2. Open printhead (K) by turning the red pressure lever (J) anticlockwise. 3. Remove the outside label mounting plate (A). 4. Load the label roll with inner winding onto the unwinding roll (B). 5. Attach again the label mounting plate (A). 6. Lead the label

  • Carl Valentin PICA II, Service Functions Pica II Series 44 Operating Manual 10.15 Press key to arrive the next menu. Select Printer Language Press keys + or + to select the printer language. The following languages are available: German, English, French, Spanish, Finnish, Czech (option), Portuguese, Dutch, Italian, Danish and Polish. Press key to confirm the selection. Press key to arrive the next menu. Select Printer Emulation Press keys + or + to change the protocol. Change between CVPL protocol and ZPL II ® protocol. CVPL: Carl Valentin Programming Language ZPL: Zebra ® Programming Language Press key

Related Products and Documents (Printer):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 HTC NEXUS ONE Operation & user’s manual htc/nexus-one-3AD.pdf 16 Apr 2023 320
2 Gourmia GMF2600 Operation & user’s manual gourmia/gmf2600-MB2.pdf 15 Jul 2022 22
3 Chargetek CK150-2 Installation manual chargetek/ck150-2-K89.pdf 13 Mar 2023 2
4 Baumer G25 Assembly instructions baumer/g25-35X.pdf 25 Aug 2023 2
5 Philips WACS4500 Specifications philips/wacs4500-4V3.pdf 20 Jun 2023 3 1.65 Mb
6 Troy-Bilt TBBV Operator's manual troy-bilt/tbbv-N7C.pdf 22 Aug 2022 36 0.91 Mb

Similar Resources:

  • KERN

    911-013

    (12 pages)
    KERN & Sohn GmbH Ziegelei 1 D-72336 Balingen E-Mail: [email protected] Phone: +49-[0]7433- 9933-0 Fax: +49-[0]7433-9933-149 Internet: www.kern-sohn.com Operating Instructions Dot Matrix Printer KERN 911-013 Version 1.0 12/2015 GB 911-013-e-1510 …
  • Epson

    Epson Stylus NX330

    (4 pages)
    4 Slide the edge guide to the left.5 Load paper against the right edge guide and behind the tab, with the printable side faceup.8½ × 11 inch(216 × 279 mm) 4 × 6 inch(102 × 152 mm) Note: Don’t load the paper sideways; always load it short edge first.6 Slide the edge guide over, against the left edge of the paper.7 Flip the feeder guard back. Read …
  • Oki

    OKIPAGE 10ex

    (2 pages)
    DIGITAL LED PRINTERSTo propel your company into the future,you need technology that fits the wayyou work.You need the OKIPAGE®10ex,the best-featured desktop printer in itsclass.This digital LED printer combinesprofessional performance with excep-tional value, for years of high-quality documents and low ongoingoperating costs.Not only does itprint at a fast …
  • HP

    E M601

    (8 pages)
    ENInstallation GuideLASERJET ENTERPRISE M601, M602, M603FRGuide d’installationBGРъководство за инсталиранеELΟδηγός εγκατάστασηςKKОрнату нұсқаулығыRUРуководство по установкеTRYükleme KılavuzuUKПосібник зі встановленняAR …
  • Xerox

    Phaser 7760

    (2 pages)
    0HASERCOLORLASERPRINTERWWWXEROXCOMOFFICESUPPORT83ETUP6IDEO0RINTER$RIVERSAND5TILITIES3UPPORT#ENTREAND$OCUMENTATION#$2/-3OFTWARE …
  • Lexmark

    C950 Series

    (2 pages)
    Moving guideSelecting a location for the printerCAUTION—POTENTIAL INJURY: The printer weight is greater than 18 kg (40 lb) and requires two or more trained personnelto lift it safely.When selecting a location for the printer, leave enough room to open trays, covers, and doors. If you plan to install any options,then leave enough room for them too. It is im …

Comments, Questions and Opinions: