Challenger APFWKGSM Operating Manual

Text of Challenger APFWKGSM User Guide:

• Challenger APFWKGSM, APFWKGSM GSM Wireless Alarm Operating Manual APFWKGSM Manual Rev01 - 19 - 6. 5 – Setup system The catalog of Setup system contains five parts. They are list as follow: 1 = Bell Time, 2 = Set Time, 3 = Set Date, 4 = GSM Receiving Signal Level Display, 5 = Reset NVM( non-volatile memory) 6.5.1 – Entering Bell Time This is the duration that the external bell output is active. The range is 01-20 minutes. The default is 14 minutes. e.g. Change the Bell Time from 3 to 10 minutes. Under Master Menu ·Press keys to go into Setup System

• Challenger APFWKGSM, APFWKGSM GSM Wireless Alarm Operating Manual APFWKGSM Manual Rev01 - 31 - Wireless Door/Window Contact Detector (MC) Symptoms Possible causes and cures Does not detect opening of door or window (Red LED does not flash) Check that batteries are correctly installed. Check that magnet is correctly positioned. Built-in buzzer makes a sound Batteries are low. Replace batteries Wireless PIR detector (PIR) Symptoms Possible causes and

• Challenger APFWKGSM, APFWKGSM GSM Wireless Alarm Operating Manual APFWKGSM Manual Rev01 - 33 - Wireless Remote Key Type Microprocessor based wireless remote control key Housing Material ABS LED Transmission indication Transmission Frequency 433MHz Transmission Range 30 meters (open air with direct line of sight) Power Supply 3VDC (1 x CR2032 Lithium Coin size Battery) External Sounder Housing Material ABS Rated Voltage 12VDC Sound Output Level 105dB Control Panel External Power Supp

• APFWKGSM GSM Wireless Alarm Operating Manual APFWKGSM Manual Rev01 - 2 - Table of Contents SECTION 1 – OVERVIEW OF SYSTEM .......................................................... - 5 - 1.1 – System Feature........................................................................................................................

• Challenger APFWKGSM, APFWKGSM GSM Wireless Alarm Operating Manual APFWKGSM Manual Rev01 - 32 - Section 10 – Specifications GSM Wireless Alarm Panel Type of Alarm Panel Microprocessor based control unit Housing ABS Entry Delay default 30 seconds, programmable Exit Delay default 30 seconds, programmable Alarm Zone 10 Zones - Programmable function External Speaker DC12V 16ohm, max current : 200mA Siren Duration Default 3 minutes Current consumption control panel Standby : 75mA Alarm : 240mA Battery input voltage Alkaline bat

• Challenger APFWKGSM, APFWKGSM GSM Wireless Alarm Operating Manual APFWKGSM Manual Rev01 - 17 - 6.2.4 – Setting Delay Time function This is the time allowed to leave the premises via the exit route before the system arms (Entry/Exit time), and entry route to disarm the system before the system goes into alarm. The programmable range is 00-99 seconds. The default is 30 seconds. Under Master Menu/Setup Program, the program mode is chosen. ( Full or Part ) ·Press to select Delay Time function. ·Press to accept. Display current exit time number. Set the time b

• Challenger APFWKGSM, APFWKGSM GSM Wireless Alarm Operating Manual APFWKGSM Manual Rev01 - 30 - 7.1.8 – SMS Content of feedback for system action Action event SMS content ARM Full action(1234armf) System is in Full Mode. --Phone Name. ARM Part action(1234armp) System is in Part Mode. --Phone Name. DISARM action(1234disarm) System is in Day Mode. --Phone Name. DISARM action(1234disarm) System is disarmed from alarm

• Challenger APFWKGSM, APFWKGSM GSM Wireless Alarm Operating Manual APFWKGSM Manual Rev01 - 12 - Section 5 – First Power Up Before powering up the GSM panel – fit the top cover on to the base. Connect the speaker wires and the SIM Card inserted. a. On connecting the battery the system will now go into alarm condition. b. Fit the cover to hold down the tamper spring at the bottom right-hand of the board. c. Enter Master code (factory set code). d. Press to return to Day mode. Power Up 1 2 3 4 RESET 01-Jan 00:00 DAY Ba

• APFWKGSM GSM Wireless Alarm Operating Manual APFWKGSM Manual Rev01 - 10 - 2.5 – Extension speaker Extension speaker may be connected to the loudspeaker terminals to produce high volume alarm tones. External speaker connects to control panel Extension speakers may be wired across the speaker terminals(Red to +and

• Challenger APFWKGSM, APFWKGSM GSM Wireless Alarm Operating Manual APFWKGSM Manual Rev01 - 36 - CHALLENGER SECURITY PRODUCTS 10 Sandersons Way Marton Blackpool FY4 4NB Tel No: 0044 1253 791 888 Tech No: 0044 1253 792 898 Website: www.challenger.co.uk Email: [email protected]

• Challenger APFWKGSM, APFWKGSM GSM Wireless Alarm Operating Manual APFWKGSM Manual Rev01 - 3 - 6.3.1 – Setting Zone Name ................................................................................................................. - 17 - 6. 4 – Change Code .............................................................................................................................. - 18 - 6. 4.1 – Changing Master Code .......................................................................................................... - 18 - 6. 5 – Setup system .............................................................................

• Challenger APFWKGSM, APFWKGSM GSM Wireless Alarm Operating Manual APFWKGSM Manual Rev01 - 28 - Note: Wireless remote could set full mode and part mode. Pressing the “disarm” botton on the wireless key will disarm the system. 7.1.2 – How to use SMS to set the system ·System is in Day mode. ·Input command message “1234armf” to set system FULL Mode. ·Input command message “1234armp” to set system PART Mode. When no fault, it will display “Exit–No Faults” and the exit to

• Challenger APFWKGSM, APFWKGSM GSM Wireless Alarm Operating Manual APFWKGSM Manual Rev01 - 1 - POWER APFWKGSM – GSM WIRELESS ALARM OPERATING Manual SAFETY Before proceeding with the installation, please note the following safety warnings: DO NOT connect the mains supply directly to the products, this will cause permanent damage to the products. Control panel is for indoor use only. Avoid mounting location which can expose this product to splashing or dripping liq

• Challenger APFWKGSM, APFWKGSM GSM Wireless Alarm Operating Manual APFWKGSM Manual Rev01 - 34 - Appendix 1 – Event Log Messages Keypad text Description Power up Supply power on Code Changed Master Master code be changed Battery Low Battery low voltage Battery Low Z No: Zone Name Wireless Zone Low battery AC Power Off Mains power supply failure System SET System into Set mode System Disaram User has disarmed the system Disarm from Alarm User has disarmed the

• APFWKGSM GSM Wireless Alarm Operating Manual APFWKGSM Manual Rev01 - 13 - Section 6 – How to Set up the system Master Program Mode The control panel may be programmed to suit a wide variety of installations. Once the master program mode has been accessed, each configuration may be changed in any order. Before

• Challenger APFWKGSM, APFWKGSM GSM Wireless Alarm Operating Manual APFWKGSM Manual Rev01 - 27 - Section 7 – Using System After you have finished system settings, you can now use the system. This section gives an operation of how to arm and disarm the system as well as how to reset after an alarm. 7.1 – Setting the System The panel has two programs: Program Full, Program Part. Both can be programmed independently in the master operations mode. So you can set the system to the corresponding mode: Full Mode, Part Mode 7.1.1 – Using the keyboard on control panel to setup ·System is in Day mod

• Challenger APFWKGSM, APFWKGSM GSM Wireless Alarm Operating Manual APFWKGSM Manual Rev01 - 16 - 6.2.2 – Part mode Setting ·Under Master mode. ·Press to select Setup Programs. ·Press to accept and go into Setup Part Mode. 6.2.3 – Setting zone function In Zone Function, Security type zones can be assigned with different functions. These are 1= Immediate Zone, 2 = Delay Zone Immediate Zone: Use this function when the zone is not part of an entry/exit route. When the system is SET, activation of an imme

• Challenger APFWKGSM, APFWKGSM GSM Wireless Alarm Operating Manual APFWKGSM Manual Rev01 - 8 - 2.2 – Fixing the Control Panel CAUTION: When positioning the control panel ensure that it is located in a dry place. Step 1. Remove the backgraund cover(s) from the base assembly. Step 2. Carefully remove the board by taking away screws at both edges Step 3. Fit the panel to wall with suitable fixings. Ensure the wall surface is flat to prevent base distortion. There are cable entry holes provided in the rear of the base and around the outside edges

• Challenger APFWKGSM, APFWKGSM GSM Wireless Alarm Operating Manual APFWKGSM Manual Rev01 - 20 - ·Press to select Set Time function. ·Press to accept. Display current time. set new time to 12:02 ·Press number keys. ·Press to save it and clear second time, or press to cancel, it will exit and go to “Set Date”. 6.5.3 – Entering Set Date Using digital keys or key to change the date, pressing the key to save or pressing key to cancel. The date can be changed in day, month, year format DD/MM/YY. The method

• Challenger APFWKGSM, APFWKGSM GSM Wireless Alarm Operating Manual APFWKGSM Manual Rev01 - 18 - ·Press key, it will clear the last character. ·Press key, it will clear the line text. [0]..[9] key have different characters. _0 ,)?1 abc2 def3 ghi4 jkl5 mno6 pqrs7 tuv8 wxyz9 ·Press key twice within 3 seconds. Capital 'B' will be shown on LCD. ·Press key to toggle between capital and lower case lett

• Challenger APFWKGSM, APFWKGSM GSM Wireless Alarm Operating Manual APFWKGSM Manual Rev01 - 25 - 6.8.2 – How to delete all wireless remote keys ·Under Master menu ·Press keys to go into Setup WL Device function. ·Press key to select Setup WL Key function. ·Press key go into delete all keys function. ·Press key to delete key ID record or press to reject change. ·Press any key to exit “Setup WL Key”. 6.8.3 – How to learn a wirele

• Challenger APFWKGSM, APFWKGSM GSM Wireless Alarm Operating Manual APFWKGSM Manual Rev01 - 7 - PIR 2 - 2.5M  Designed to detect a door or window opening. The detector is usually mounted next to it on the door or window. For optimum wireless range, they should be mounted as high as possible.  In most applications, it is fitted to the front door. Having chosen the location, do not mount at this stage. Wireless Movement / Passive Infrared Detector (PIR) – Location  The detector should not be mounted near to large m

• Challenger APFWKGSM, APFWKGSM GSM Wireless Alarm Operating Manual APFWKGSM Manual Rev01 - 21 - 6.5.4 – Setting GSM Signal Level Display When this flag is set to ON, system will check the antenna of GSM module receving signal level all the time and show level through this icon “ ”. Under Master Menu ·Press keys to go into Setup System function. ·Press to select GSM Signal Diplay function. ·Press or key to toggle ON/OFF.

• APFWKGSM GSM Wireless Alarm Operating Manual APFWKGSM Manual Rev01 - 26 - 6.8.4 – How to delete a wireless zone ·Under Master menu ·Press keys to go into Setup WL Device function. ·Press key to select Setup WL Zone function ·Press keys to select zone 5. Note

• Challenger APFWKGSM, APFWKGSM GSM Wireless Alarm Operating Manual APFWKGSM Manual Rev01 - 15 - ·Press key twice within 3 seconds. Lower case 'e' will be shown on LCD. ·Input “Helen” string. ·Press key to accept input and save the text, ·Press key, it will exit without change to the text. 6.1.4 – Deleting the Mobile Phone Number ·Under Master mode. ·Press keys to go into Set Mobile No function. ·Press to select phone 1 Note:

Related Products and Documents (Security System):

Comparable Devices:

Similar Resources:

• MEDC CU1 (20 pages) Please note that every care has been taken to ensure the accuracy of our technical manual. We do not, however, accept responsibility for damage, loss or expense resulting from any error or omission. We reserve the right to make alterations in line with technical advances and industry standards. Toutes les précautions ont été prises pour garantir la préci …

• Honeywell SEF8MS (6 pages) Back plate / Embase arrière / Placa trasera / Piastra posteriore 1357Spirit Level / Niveau à bulle / Nivel de aire / Livella Top Mounting hole / Trou de montage supérieur / Orificio de montaje superior / Foro di montaggio superiore Main board / Carte principale / Placa principal / Scheda principale Mounting hole / Trous de montage / Orific …

• Conrad 75 10 52 (2 pages) Version 06/02Tür-/Fensteralarm °Best.-Nr. 75 10 52Bestimmungsgemäße VerwendungBei diesem Tür-/Fensteralarm handelt es sich um ein Sicherheitsprodukt welchesEinbrecher abschreckt. Die Alarmaktivierung erfolgt über Magnetkontakt. Die Spannungsversorgung erfolgt durch drei Knopfzellen á 1,5 Volt DC.Der Kontakt mit Feuchtigkeit ist unbedingt zu vermeiden! …

• urmet domus 1092 (12 pages) + DS1092-537 BALL CAMERA AHD 4M DAY & NIGHT 1/3” OTTICA 3,6MM CON LED IR 4M AHD DAY & NIGHT BALL CAMERA 1/3” 3,6MM LENS WITH IR LED AHD 4M TAG & NACHT KUGELKAMERA 1/3-ZOLL 3,6 MM-OBJEKTIV MIT IR-LEDS CAMÉRA MINI-DÔME AHD 4M DAY & NIGHT 1/3” OPTIQUE 3,6 mm A DIODES IR CÁMARA MINIDOMO AHD 4M DÍA/NOCHE 1/3” ÓPTICA 3,6 mm CON L …

• CyberData 011527 (24 pages) CyberData InformaCast Enabled WiFi Alert Button Setup Guide Document Part # 931822B CyberData Corporation 3 Justin Court Monterey, CA 93940 (831) 373-2601 …

• Baretta Security Systems Advantage (4 pages) TWO-WAY REMOTE AUTO ALARM SYSTEMINSTALLATION MANUALADVANTAGEAlarm Features One 5 Button Two Way LCD Display With Pager, Vibration Remote One 5 Button Remote Control Built-In Side-Light Relay Programmable (+/-) Plug-in user programmable Override Switch Plug-in Dual-Zone Piezo Sensor Horn Output Remote Door Locking/Unlocking with posit …

Comments, Questions and Opinions: