Channel Safety Systems Zerio Plus Instruction Manual
|
Channel Safety Systems Zerio Plus, INSTRUCTION MANUAL - Issue 1 - 07/2014 | 34 CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk 8.0 - TEST MODE Test mode allows a system to be tested with minimal disruption to the occupants of a building. When a zone is placed into test mode the engineer can choose to disable sounders, actuators or any output devices. Should anything happen outside of these selected zones the system will operate as normal and the sounders will sound. Once the various Test Mode parameters have been chosen, the Test Mode LED
Channel Safety Systems Zerio Plus, INSTRUCTION MANUAL - Issue 1 - 07/2014 | 21 CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk 6.9 - System Options – commissioning users 1.Main Menu>>1.Setup>>4.System Setup>>3.Edit Panel>>1.Panel Options>>2.System Options This menu allows the user to change overall system settings. Alarm Verify Time (seconds) that a device has to be in alarm to generate an alarm condition on the panel. 2 seconds has been type approved. Antenna Type Specify if the main panel is
Channel Safety Systems Zerio Plus, INSTRUCTION MANUAL - Issue 1 - 07/2014 | 4 CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk CONTENTS 1.0 EN54 Approved Con guration 2.0 Installation 3.0 Front Panel Layout 4.0 User Operation 4.1 System Normal 4.2 Fault Conditions 4.3 Silence Buzzer 4.4 Reset a Fault 4.5 Alarm Conditions 4.6 Silence the Alarm 4.7 Re-sound the Sounders 4.8 Reset the Alarm 4.9 Access Levels 5.0 Menu Operation 5.1 Quick Menu
Channel Safety Systems Zerio Plus, INSTRUCTION MANUAL CHANNEL SAFETY SYSTEMS t: 0845 884 7000 Peters eld Business Park f: 0845 884 6000 Bedford Road Peters eld Hampshire e: [email protected] GU32 3QA w: www.channelsafety.co.uk Zerio Plus Wireless system from Channel Safety Systems
Channel Safety Systems Zerio Plus, INSTRUCTION MANUAL - Issue 1 - 07/2014 | 12 CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk 3.0 - USER OPERATION 4.1 - System Normal In normal operation the screen will show either the date and time, or the supplier/service contact details. The unit can also be con gured to alternate between the two. If con gured this way, the display will change every 4 seconds. See 6.4 – Programming Agent Details. Also a single gre
INSTRUCTION MANUAL - Issue 1 - 07/2014 | 20 CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk 6.8 - User Options – commissioning users 1.Main Menu>>1.Setup>>4.System Setup>>3.Edit Panel>>1.Panel Options>>1.User Options Detailed below are the other options that can be changed related to the pan
Channel Safety Systems Zerio Plus, INSTRUCTION MANUAL - Issue 1 - 07/2014 | 45 CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk The Zerio Plus system should be maintained in accordance with the regulations and codes appropriate to the country of installation. This schedule is based on BS5839 codes of practice. Daily Actions The user should check that the panel indicates normal operation. If any faults exist, they should be recorded and the responsible person or maintenance company should be noti ed. Weekly Actions The user should put at least one
INSTRUCTION MANUAL - Issue 1 - 07/2014 | 23 CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk 6.15 - Input Options – commissioning users 1.Main Menu>>1.Setup>>4.System Setup>>3.Edit Panel>>2.Panel Inputs>>1.Input Options This menu allows the user to set op
Channel Safety Systems Zerio Plus, INSTRUCTION MANUAL - Issue 1 - 07/2014 | 18 CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk 6.6 - Set up a New System (Standard) – commissioning users 1.Main Menu>>1.Setup>>4.System Setup>>2.New Setup>>1.Standard System Devices are programmed via a radio link to the control panel. If the system is known to have been used before then all the devices that are logged on to the system must be removed rst. To add or remove de- vices on a system that is already set up; see 6.29 – Add Device and 6.30 – Remove Device. Press Enter to start. You will be asked if you wou
Channel Safety Systems Zerio Plus, INSTRUCTION MANUAL - Issue 1 - 07/2014 | 13 CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk 4.6 - Silence the Alarm When it is certain that it is safe to return to the building the Silence Alarm button should be pressed. The user will then be prompted to enter a valid user access code using the navigation keys. Up to 30 seconds should then be allowed for all sounders to silence. If a device is still in an alarm condition the sounders will not sound again unless another device goes into alarm.
Channel Safety Systems Zerio Plus, INSTRUCTION MANUAL - Issue 1 - 07/2014 | 35 CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk 8.3 - Lamp/Buzzer Test – advanced, service and commissioning users 1.Main Menu>>3.Test Mode>>3.Lamp/Buzzer Test This option will illuminate all the panels LEDs in sequence, to check they are working properly. The panel buzzer will also sound. If the buzzer does not sound, check the buzzer enable jumper link is tted on the main processor board. See page 10 –PCB Layout. A quick lamp test can be performed from any screen by holding down the Menu button for 2 seconds. 8.4 - Enable System Test – service
Channel Safety Systems Zerio Plus, INSTRUCTION MANUAL - Issue 1 - 07/2014 | 44 CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk How do I change the battery in a device? Remove the device from its base plate. Unscrew and remove the rear casing from the device. Pull out the existing battery, paying attention to where the connecting pins are. Line up the new battery with the connecting pins and push into place. Screw the rear casing back on and perform a battery reset; see 12.0 – Battery Stats Reset. Return the device to its base plate. How do I program a device? See 6.29 – Adding a device and 6.34 – Reprogram device. How do I add a booster pane
Channel Safety Systems Zerio Plus, INSTRUCTION MANUAL - Issue 1 - 07/2014 | 7 CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk Battery In order to meet EN54 Part 4, a Yuasa NP7-12 lead acid battery should be tted. This will give a 72 hour standby, assuming no external equipment (eg wired antennas) has been added. If only 24 hours standby is required and no external equipment has been tted then a 12V 2.8Ahr battery could be tted. Con- nect the battery using the supplied terminal connections. The red wire is +12V and the black wire is 0V. Do not confuse the colour of the terminal c
Channel Safety Systems Zerio Plus, INSTRUCTION MANUAL - Issue 1 - 07/2014 | 25 CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk 6.22 - Add Antenna – commissioning users 1.Main Menu>>1.Setup>>4.System Setup>>5.Add Hardware>>1.Add Antenna Power down the panel before connecting the wired antenna. Once powered up, check that the supply light is illuminated on the antenna and that the status light is ashing. Navigate to the add antenna menu and press . Select the wired antenna (E00001), press and press Enter. Once added
Channel Safety Systems Zerio Plus, INSTRUCTION MANUAL - Issue 1 - 07/2014 | 47 CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk Product Descriptions 18.0 - ZERIO PLUS HARDWARE PANELS F/EDA-Z5008 8 zone Zerio Plus control panel (requires 12/7 battery) F/EDA-Z5020 20 zone Zerio Plus control panel (requires 12/7 battery) N/CH12/7 12V 7AH battery DEVICES F/EDA-R5000 Zerio Plus optical smoke detector (requires 1 x S/BATT/EDA-Q690 battery) F/EDA-R6000 Zerio Plus optical smoke detector complete with sounder (requires 2 x S/BATT/EDA-Q690 batteries) F/EDA-R6030 Zerio Plus optical smoke detector complete with sounder visual indicator (requires 1 x S/BATT/EDA-Q
Channel Safety Systems Zerio Plus, INSTRUCTION MANUAL - Issue 1 - 07/2014 | 29 CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk 6.30 - Remove a Device – commissioning users 1.Main Menu>>1.Setup>>5.Device Setup>>3.Remove Device>>1.Remove One Device If a device is not required on the system it must be deleted to prevent it causing a verify fault once powered down. From the Device Setup menu select ‘3 – Remove Device’ then sele
Channel Safety Systems Zerio Plus, INSTRUCTION MANUAL CHANNEL SAFETY SYSTEMS t: 0845 884 7000 Peters eld Business Park f: 0845 884 6000 Bedford Road Peters eld Hampshire e: [email protected] GU32 3QA w: www.channelsafety.co.uk
INSTRUCTION MANUAL - Issue 1 - 07/2014 | 2 CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk Zerio Plus has been designed to be capable of handling 240 devices in 100 zones. Typical installations would include small o ces, private houses, HMO’s, guest houses and small hotels. This man
Channel Safety Systems Zerio Plus, INSTRUCTION MANUAL - Issue 1 - 07/2014 | 8 CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk PCB Layout Monitored Inputs The panel features two monitored inputs that can be programmed either as latching or non-latching. It is impor- tant to note that before using these inputs they must be enabled by programming them in the panel options menu. If the inputs are enabled then 4K7 end of line resistors must be tted at the termination. Applying a 470 resistor across the inputs will produce a ‘Fire’ message. The inputs are labelled ‘INPUTS’ and ‘No1’ and ‘No2’. These inputs can be assign
Channel Safety Systems Zerio Plus, INSTRUCTION MANUAL - Issue 1 - 07/2014 | 46 CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk There are no user serviceable parts within the Zerio Plus panel. Only trained service engineers should carry out the repairs listed below. Contact EDA Technical for further information. Power Supply Before removing the PSU remove the mains fuse from the terminal block and disconnect the battery. The display should be o and no LEDs should be illuminated; inside or outside the panel. Unplug the PSU connector on the EDA-Q2010 processor board (see diagram on page 10). Remove the live, earth and n
INSTRUCTION MANUAL - Issue 1 - 07/2014 | 42 CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk 13.0 - FAULTS The panel continuously monitors hardware, battery life and connections across the system. If a fault is found, it will be displayed on the panel screen, the buzzer will sound and the common
Channel Safety Systems Zerio Plus, INSTRUCTION MANUAL - Issue 1 - 07/2014 | 33 CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk Enable a Zone – all access levels 1.Main Menu>>2.Disable/Enable>>2.Enable>>1.Zone To enable a previously disabled zone, select it using the or keys and press Enter. To enable more zones press Enter, or Cancel to exit. If all zones have been enabled ‘No Zones to enable’ will be displayed. If a disabled zone is enabled; and no other isolated devices/zones remain, then the ‘Disablements’ LED will extinguish. Enable a Device
INSTRUCTION MANUAL - Issue 1 - 07/2014 | 26 CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk 6.26 - Panel Network In a traditional setup, all radio booster panels will communicate directly with the main panel. The system also has the capability for the signal to ‘hop’, as shown below. In this exa
Channel Safety Systems Zerio Plus, INSTRUCTION MANUAL - Issue 1 - 07/2014 | 24 CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk 6.18 - Panel Text – commissioning users 1.Main Menu>>1.Setup>>4.System Setup>>3.Edit Panel>>3.Panel Text This menu allows the user to set a name and/or location for the panel. This will be displayed on the system normal screen. Enter text using the panel keys or by connecting a standard USB keyboard. 6.19 - SIM Operations – commissioning users 1.Main Menu>>1.Setup>>4.System Setup>>3.Edit Panel>>4.SIM Operations The memory card should be
Channel Safety Systems Zerio Plus, INSTRUCTION MANUAL - Issue 1 - 07/2014 | 15 CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk 6.1 - Changing the system Time and Date – all access levels 1.Main Menu>>1.Setup>>1.Time & Date To change the time and date settings use the and keys to navigate to the value, and the or keys to select the desired value. Press Enter to accept or Cancel to exit. The Zerio Plus panel automatically adjusts the clock for daylight savings. Should complete power be
Channel Safety Systems Zerio Plus, INSTRUCTION MANUAL - Issue 1 - 07/2014 | 10 CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk 3.0 - FRONT PANEL LAYOUT 1. Fire LEDs In a re condition, these LEDs will ash. 2. Zone Alarm LEDs In a re condition, the appropriate zone LED will illuminate. If the re condition exists across multiple zones, multiple zone LEDs will be illuminated. *The EDA-Z5008 8 Zone panel is shown. The EDA-Z5020 panel is equipped with 20 zone LEDs and the EDA-Z5100 is equipped with 100 zone LEDs 3. Status LEDs Supply This LED will be illuminated when mains power is p
Channel Safety Systems Zerio Plus, INSTRUCTION MANUAL - Issue 1 - 07/2014 | 19 CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk 6.7 - Set up a New System (HMO) – commissioning users 1.Main Menu>>1.Setup>>4.System Setup>>2.New Setup>>2.HMO System The HMO setup reduces disruption to residents in other ats by false alarm. Note that the HMO setup is not EN54 approved. Upon activation within a at, an alert tone will be sounded in that at. Residents can have the ability of silencing these alarms using the Silence Buttons (EDA- T5100) instead of visiting the main control panel. Should those
Channel Safety Systems Zerio Plus, INSTRUCTION MANUAL - Issue 1 - 07/2014 | 11 CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk Cancel Used to return to the main screen from a menu or to return to the menu from a programming screen. Enter This is used to accept information programmed into the panel. Re-sound Alarm Following an alarm condition that has been silenced, this button will re- sound the alarm. Silence Alarm If the panel is in a re condition this will silence the sounders. Silence Buzzer Silences the panel buzzer for all currently displayed faults or alarms. Reset Resets the panel from an alar
Channel Safety Systems Zerio Plus, INSTRUCTION MANUAL - Issue 1 - 07/2014 | 31 CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk Disable a Zone – all access levels 1.Main Menu>>2.Disable/Enable>>1.Disable>>1.Zone If a zone is disabled the system will not display any re or fault events for devices located in that zone. This includes any call point activations. Select the zone number to be disabled and press the key. Select the time-out period followed by the key. All access levels can disable a zone for a pe- riod of 1 to 96 hours. A commissioning user can disable a zone inde nitely by selectin
DOWNLOAD |
Cisco 500 Series Security System Operation & user’s manual
500 Series |
Cisco Universal Broadband Router uBR7200 Security System Hardware installation manual
Universal Broadband Router uBR7200 |
Uniden G955 Security System Operation & user’s manual
G955 |
VCOMTECH VCOM Air X Security System Operation & user’s manual
VCOM Air X |
Digimerge DH200 Security System Instruction manual
DH200 |
DKS 1816 Security System Owner's manual
1816 |
Uplink 4550-CB Security System Installation & user manual
4550-CB |
Viper 650XV Security System Installation manual
650XV |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Accusplit | Eagle 970-069 | Operating instructions | accusplit/eagle-970-069-D6W.pdf | 10 Sep 2023 | 2 | 0.31 Mb |
2 | Kenwood | KDC-252U | Instruction manual | kenwood/kdc-252u-HED.pdf | 05 Mar 2023 | 62 | |
3 | Pure Reliability | Solo 1200 | Installation and use manual | pure-reliability/solo-1200-8ID.pdf | 20 Jun 2023 | 18 | |
4 | Samsung | MCM-A202A | Operation & user’s manual | samsung/mcm-a202a-F9M.pdf | 23 Aug 2023 | 8 | |
5 | Coleman | 4D PACK-AWAY | How to use and enjoy | coleman/4d-pack-away-C54.pdf | 11 Aug 2022 | 2 | 0.53 Mb |
6 | SC2000 | LGR1556X | Instructions | sc2000/lgr1556x-PUA.pdf | 30 Apr 2023 | 2 |
Honeywell
K0904V1 2/06 Rev. B ADEMCO 6160RF Keypad/TransceiverUser Guide KEYPAD DISPLAYS AND LEDS The 6160RF has the following features: • Large backlit, 2-line, 32-character alphanumeric LCD. • 16 large telephone-style backlit keys located behind a decorative door that swings down to provide access to the keys. • System numerals, imprinted in large t …
6160RF(2 pages) |
Vigilant
Ref: PBG0215 9 October 2018 Page 1 of 8 T-GEN2 GRADE 3 BUILDING OCCUPANT WARNING SYSTEM The VIGILANT T-Gen2 Emergency Warning System is available as two complete Grade 3 Building Occupant Warning Systems (BOWS) – 8U @ 60W and 15U @ 120W. New versions approved to AS 4428.16 replace the earlier models. The VIGILANT T-Gen2 Building Occupant Warning Sys …
T-Gen2(8 pages) |
POSIFLEX
Part 1 FCC Notes: This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules, which are desig …
KV-2000 Series(10 pages) |
As Pool
User GuidN Stres wit smartphonN Stres, how i work ?v. 1.3.0*This distance is indicative and variable if obstacles, depending on the na-ture of the environment, the power of batteries and the type of smartphone used (see rules of good practice with No Stress page 8).Your smartphone and its ap-plication alerts you when a Beacon is im …
NO STRESS(24 pages) |
Eurotherm
Verdrahtung Kabelquerschnitt Die Schraubklemmen auf der Regler Rückseite sind für Kabelquerschnitte von 0,5 bis 1,5 mm2 vorgesehen (16 bis 22AWG). Die Klemmenleisten sind jeweils mit einer Kunststoffabdeckung zum Schutz vor Berührung versehen. `Achten Sie beim Anziehen der Schrauben darauf, …
3216i(4 pages) |
Foscam
V46.01 Model: FI8910W Quick Installation Guide Indoor Pan/Tilt Wireless IP Camera Black White For Windows OS ------- Page 1 For MAC OS ------- Page 11 ShenZhen Foscam …
FI8910W(21 pages) |
JVC Camcorder Everio GZ-HM670Camcorder PDF Detailed user manual Everio GZ-HM670, 133 |
Sierra Wireless Modem GL8200Sierra Wireless Product User Guide: GL8200 PDF Installation & user manual - 1HVXX3 GL8200, 24 |
AirPatrol Lite Network Router AirPatrolNetwork Router #U1TVU8 AirPatrol, 176 |
LEXIBOOK Digital Photo Frame CADRE PHOTO NUMERIQUELEXIBOOK Digital Photo Frame Manual (File: lexibook-cadre-photo-numerique-manual-60, Monday 25-09-2023) CADRE PHOTO NUMERIQUE, 60 |
Black+Decker Oven TOD3300 SeriesUse and care manual for Black+Decker TOD3300 Series Oven TOD3300 Series, 12 |
Raymarine GPS Apelco DXL-6100Raymarine GPS Operation & user’s manual (File: raymarine-apelco-dxl-6100-gps-86, 14.09.2023) Apelco DXL-6100, 86 |
Miele Dishwasher NOVOTRONIC G 842 PLUSOperating instructions manual for Miele NOVOTRONIC G 842 PLUS Dishwasher NOVOTRONIC G 842 PLUS, 48 |
Sharp Air Conditioner KC-6400ESharp KC-6400E User Guide (Operation manual), @AVSGPJ KC-6400E, 24 |
Haier Air Conditioner H2SM-14H03Haier H2SM-14H03 Air Conditioner Operation manual H2SM-14H03, 20 |
Metra Electronics Automobile Accessories 99-4644#EF955N 99-4644: Metra Electronics Automobile Accessories Owner Documentation 99-4644, 28 |
Toto Link Network Router A3002RUNetwork Router #LR41A3 A3002RU, 1 |
Kenwood Amplifier KA-V9500Amplifier Instruction manual (Kenwood KA-V9500) KA-V9500, 44 |