Manualios.com

CIAAT CTP-3010 Operation & User’s Manual

CIAAT CTP-3010 Manual Online:

4.85, 1701 votes
CIAAT CTP-3010 User Manual
CIAAT CTP-3010 User Guide
CIAAT CTP-3010 Online Manual

Text of CIAAT CTP-3010 User Guide:

  • CIAAT CTP-3010, CONTENTS PREFACE Chapter 1. Important Safety Instruction Environments ................................................................................................. Handling Instruction ....................................................................................... Handling Instruction - Continued from previous page .................................... Handling Instruction for Consumable and Printed Output .............................. Chapter 2. Installing and Set Up Unpacking and checking the accessories ...................................................... Parts Name and Function ........................

  • CIAAT CTP-3010, Chapter 1. Important Safety Instruction 1-1 This manual provides detail instructions for the safety use of the printer. Please read this manual carefully before operating the printer to ensure having proper use. To use the printer safety, please pay attention to the followings: In this manual, there are notes that require special attention. For your safety operation, Safety Notices are separated as follows; It is difficult to forecast all the danger in setting and use of the printer. Therefore, warnings in this Operation Manual, in the other documents on the printer cannot cover all the cases. In case of performing the operation or mainte

  • Chapter 1. Important Safety Instruction 1-2 When handling the printer, please pay attention to the followings; Warning: Lift the printer from its box and put it onto a flat and firm table or desk. Warning: The printer alone (without paper and ribbon installed) is weighted around 27Kgs. Please handle the printer carefully to prevent personal injury and damage of the

  • CIAAT CTP-3010, Chapter 1. Important Safety Instruction 1-3 In handling the ink ribbon, paper and printed outputs, please pay attention to the followings; Attention: Paper Handling ƦUse only the paper specified by Ciaat. ƦStore the paper flat. ƦStore the paper in a dry and dark place to avoid direct sunlight. (Temperature less than 30ƫ, Humidity: lass than 60%). ƦDo not touch the paper surface before printing to avoid fingerprints. Attention: Ink Ribbon Handling ƦUse only the ink ribbon specified by Ciaat.

  • CIAAT CTP-3010, Chapter 2. Installing and Set Up 2-1 This chapter describes the unpacking and set up of the printer. Before proceeding to this chapter, please make sure the Chapter 1. Important Safety Instruction is acknowledged carefully. 2. Open the box and remove the box containing the accessories and protection materials. 1. Please loosen carton holder on both sides first. Attention: Please retain the box and packaging materials for the transportation of the printer when necessary. 3. Take out the printer by holding the bottom of the printer. Attention: The printer alone (without paper and ribbon installed)

  • Chapter 2. Installing and Set Up 2-2 ƦParts Name and Function <Front View> <Internal View> <Rear View> NO. Name Operation Panel Front Cover Power Connector Paper Setting Lamp Control buttons, LCD and printer status display lamps are located on the panel. Open the front cover when replacing an ink ribbon or paper, or when performing maintenance. To be used to con

  • CIAAT CTP-3010, Chapter 2. Installing and Set Up 2-3 Connect the power cord according to the safety instructions below. 1. Connect the printer power cord to the back of the CTP-3010 and then plug the power cord into a power outlet. Warning: Make sure to turn off the power of the printer before inserting the power cord. Warning: Make sure to insert the power cord correctly. Incorrect insertion may cause the fire or the printer problem. Warning: Do not insert or remove the power cord with wet hands. It may cause

  • CIAAT CTP-3010, Chapter 2. Installing and Set Up 2-4 1. Connect the USB cable from the personal computer to the USB connector located on the right rear side of the printer. Be sure to insert the USB cable all the way. Attention: To remove the USB cable, make sure that the printer is in the waiting status. Removing the USB cable during data transfer may not be able to print data correctly and cause waste. ƦConnecting USB Cable user manual CTP-3010

  • CIAAT CTP-3010, Chapter 2. Installing and Set Up 2-5 1. Turn on the power of the printer by pressing "|" on the power switch. 3. Open the front cover by holding the upper section of the front cover. 2. Press the Open button on the operation panel. Attention: Do not apply pressure on the front cover when opening the front cover. Otherwise, damage may be caused to the printer. Attention: Do not open the front cover with excessive speed or with unnecessary force.

  • Chapter 2. Installing and Set Up 2-6 3. Stretch the ink ribbon and put the ink ribbon in the holder. Insert the ribbon until it clicks into position. Install spacers in the paper flanges first when using 5x7 size paper. When using 4x6 size paper or 6 x 12 size paper, spacers are not needed. (Note: The availability of some consumable packages may vary in different regions. Please

  • Chapter 2. Installing and Set Up 2-7 3. Set the paper in the printer. Set the paper by matching the color of the paper flange and the color of the holder. After setting the paper, remove the seal from the paper. 4. Insert the edge of paper under the roller by rotating the paper flanges. 5. Match both ends of the paper to the line of the seal. 6. Insert the paper

  • CIAAT CTP-3010, Chapter 2. Installing and Set Up 2-8 7. Close the front cover. After each paper roll is loaded/replaced, 4 sheets of paper will automatically be ejected to prevent dust and finger print. ƦLoading Paper Tray ƦTransporting the Printer Attention: When you use 10x15 (4x6”)-size paper, you may stack about 50 prints on this paper tray. When using the print paper of 15x30 (6x12”), it is recommended not to install the paper tray. It is recommended to remove the prints stacked on the paper tray frequently. If the prints are not removed frequently, a paper jam may occur. The following cauti

  • CIAAT CTP-3010, Chapter 3. Operation Panel 3-1 ƦOperation Panel The buttons, and LCD display on the operation panel are shown below. ƦLCD Display The LCD Display 6 indicates the following printer status. Individual Operation Buttons 1 to 5 have the following functions. NO. Name Left Button Exec Button Menu Button Right Button Use this button to select preferred setting. Press this button to cut 4 sheets of paper in “manual paper cutting” mode. Press this button to view machine status. Use this button to select preferred setting. Function 1 6 1 2 2 3 3 4 4 Open Button Press this b

  • CIAAT CTP-3010, Chapter 3. Operation Panel 3-2 ƦUser Set Up Mode To set the User Set Up Mode, press the Menu button in standby mode. When the Menu button is pressed again, display changes as follows. Display total prints Execute paper cutting Change to <Manual > mode by press Left/ Right button Display current language Change preferred language by press Left/ Right button Display the version number of the MAIN firmware. Display prints remaining/total available prints PRINTER READY menu menu menu menu menu <4X6> PRINTS MADE TOTAL [00380] MEDIA LEFT <4X6>

  • CIAAT CTP-3010, Chapter 4. Routine Maintenance 4-1 1. Use gauze; clean the heating element (glass bar) of the thermal head with ethyl alcohol. By using thermal transfer technology, daily maintenance is not really necessary if the printer has being use properly. However, in order to keep the best print quality, it is highly recommended to clean Thermal Head and Roller once in a month. ƦCleaning of Thermal Head, and Roller Caution: Make sure that the power is turned off before cleaning. Thermal Head reaches high temperature r

  • Chapter 4. Routine Maintenance 4-2 3. Use gauze dipped with ethyl alcohol, and cleans the rubber section of the guiding roller. Attention: Printing should be performed after the alcohol dried up completely (approx. 5 minutes) 4. Use gauze dipped with ethyl alcohol, and clean the rubber section of the platen roller (paper feed side). user manual C

  • CIAAT CTP-3010, Chapter 4. Routine Maintenance 4-3 Wipe the printer outer cabinet with a soft cloth. If the stains are not removed, wet the cloth and apply weakened neutral Detergent to it. 1. If the dust collects on the openings, clean it with vacuum cleaner. ƦCleaning of Outer Cabinet ƦCleaning of Filter Warning: In case of foreign substance get into the printer, turn off the power of printer, remove the power cord and contact the dealers or service center. Continuous use of the print

  • CIAAT CTP-3010, Chapter 5. Error Message Handling 5-1 ƦError Message and Corrective Action When the error happens, error message will be displayed on LCD of the operation panel. * Please advice the error code number when you contact the dealers or service center if necessary. LCD Message Status The front cover is opened The front cover is not opened No smart chip key No ink ribbon Close the front cover. Press the Open button again and reset the error Insert the smart chip key Load the ink ribbon roll. Corrective Action Installed ink ribbon does not match IC chip ID 0100 Cover Open 0101 Cover open fail 0200 Ribbon Missing 020

  • CIAAT CTP-3010, Chapter 5. Error Message Handling 5-2 ƦFailure Symptoms When detecting a failure symptom, check the printer using the following table. Symptom Power is not switch on. Check if the power cable is connected to the plug socket or the printer. Action The personal computer does not recognize the printer. Check if the USB cable is connected to the personal computer or printer. The printer does not become ready. Check if the front cover is properly closed. Check if paper is jammed in the printer. When the paper setting lamp goes off, insert the edge of the paper until the paper

  • CIAAT CTP-3010, Chapter 5. Error Message Handling 5-3 1. Open the front cover. ƦPaper Jam Attention: ƦIf the paper is used without cutting off the folded or printed section, paper jam occurs again or the ink ribbon may snap during printing. Always cut off the creased or printed section of the paper. ƦCut off the paper straight and at right angles to the roll paper direction. ƦIf paper jam occurs frequently, a defect in the mechanical section is assumed. Consult with the service center. 2. Cut off the folded or printed

  • CIAAT CTP-3010, Chapter 5. Error Message Handling 5-4 1. Stick the broken part of the ribbon with a tape. In case of power supply interrupted while the printing, the Thermal Head will be kept on pushing to Platen. Leaving this situation for a long time, the shape of Platen can be warped. In order to avoid this situation, please follow the instruction below. 1. Turn off the power of the printer. 2. Turn on the power for 3 or more seconds after turning off the power. 3. Paper Jam is displayed on the LCD of the operatio

  • CIAAT CTP-3010, Chapter 6. After-sales Service ƦSpecification 6-1 Contact your Ciaat dealers or service center for the details about after-sales service. Model Name Printing Method Resolution Printing Size & Capacity Printing Speed Operation System PC Connection Power Requirement AC 100 V ~240 V, 50-60 Hz, 6A Operation Environment Dimension Weight CIAAT CTP-3010 Dye Diffusion Thermal Transfer (D2T2 Technology) 300 x 300 dpi 4"x 6" (102 x 152 mm): 1000 prints 5"x 7" (127 x 177 mm): 600 prints 6"x 12" (152 x 304 mm): 350 print

Related Products and Documents (Printer):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 GRASS VALLEY 8950ADC Datasheet grass-valley/8950adc-58F.pdf 27 Jul 2023 1 0.21 Mb
2 Hobie SPORT CRUISER 21 Assembly manual hobie/sport-cruiser-21-Q4T.pdf 21 Jul 2022 33 1.66 Mb
3 Brother DCP-135C Quick setup manual brother/dcp-135c-N21.pdf 10 Jan 2024 26 2.95 Mb
4 Hisense LTD26K16HK Operation & user’s manual hisense/ltd26k16hk-PPF.pdf 23 Nov 2023 61
5 Skanhex SX410z Operation & user’s manual skanhex/sx410z-Y6N.pdf 11 Dec 2023 155
6 Schumacher INSTANT POWER XP650CAMO Owner's manual schumacher/instant-power-xp650camo-VA4.pdf 04 Jan 2023 20

Similar Resources:

  • Xerox

    4215

    (39 pages)
    Xerox Corporation701 S. Aviation BoulevardEl Segundo, CA 90245© 1994 by Xerox Corporation. All rightsreservedCopyright protection claimed includes all formsand matters of copyrightable material andinformation now allowed by statutory orjudicial law or hereinafter granted, includingwithout limitation, material generated from thesoftware programs which are d …
  • Canon

    imageCLASS MF6500 Series

    (214 pages)
    ENGENGBasic GuidePlease read this guide before operating this equipment.After you finish reading this guide, store it in a safe place for future reference.CANON INC.30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, JapanCANON U.S.A., INC.One Canon Plaza, Lake Success, NY 11042, U.S.A.CANON CANADA INC.6390 Dixie Road Mississauga, Ontario L5T 1P7, CanadaCANO …
  • Konica Minolta

    BIZHUB C360

    (314 pages)
    Copy OperationsUser’s GuideUser’s Guide*XXXXXXXX00**XXXXXXXX00*Konica Minolta Business Solutions Europe GmbHEuropaallee 17 30855 Langenhagen • GermanyTel.: +49 (0) 511 74 04-0Fax: +49 (0) 511 74 10 50www.konicaminolta.eu© 2009 Konica MinoltaBusiness Solutions Europe GmbHAll rights reserved. Printed in Germany. …
  • Konica Minolta

    BIZHUB PRO 1050

    (296 pages)
    • Machine Status Screen SettingSection 1: Paper Setting Section 2: Adjustment Setting Section 3: Controller Setting• Utility Screen Setting Section 4: User Setting Section 5: Machine Manager Setting• Browser Control Setting Section 6: Browser Control Setting• Appendix How to Input Characters Setting Data for Import/Export Configuration Settin …
  • Epson

    F6070

    (8 pages)
    CPD-38759EPSON PreferredSM®Limited Warranty Program for the Epson® SureColor® F6070 44-inch wide printerPriority Technical Support Toll-Free Phone NumberSecurity and Peace of MindOn-Site RepairPlease open this booklet and record your unique Unit ID Number.You will need it to take full advantage of the Preferred Warranty. …
  • TSC

    Alpha-4L-W

    (71 pages)
    WiFi +Bluetooth Version (For FCC) Alpha-4L-W, PR40-W, GR40-W, 4400-W, TSC-40-W, CN-40W, BP-40W Alpha-4L-D-W, PR40-D-W, GR40-D-W, 4400-D-W, TSC-40-D-W, CN-40LW, BP-40LW, Alpha-4L-W-R, PR40-W-R, GR40-W-R, 4400-W-R, TSC-40-W-R Alpha-4L-D-W-R, PR40-D-W-R, GR40-D-W-R, 4400-D-W-R, TSC-40-D-W-R WiFi +Bluetooth Version (For IC)Alpha-4L-D-W-R, PR40-D-W-R, GR40-D-W-R …

Comments, Questions and Opinions: