Manualios.com

Cisco SPA2102 Administration Manual

Cisco SPA2102 Manual Online:

4.05, 626 votes
Cisco SPA2102 User Manual
Cisco SPA2102 User Guide
Cisco SPA2102 Online Manual

Text of Cisco SPA2102 User Guide:

  • Cisco SPA2102, ATA Voice Field Reference Trunk Group page (SPA8000) Cisco Small Business ATA Administration Guide 185 B Trunk Group page (SPA8000) On the SPA8000, you can use the Voice tab > Trunk Group pages (T1 ... T4) to configure the Trunk Groups. This page includes the following sections:  Line Enable section section on page 185  NAT Settings section section on page 191  Network Settings section section on page 185  SIP Settings section section on page 186  Subscriber Information section section on page 189  Dial Plan section section on page 191  Proxy and Registration section section on page 199 Line Enable section Networ

  • Cisco SPA2102, Introducing Cisco Small Business Analog Telephone Adapters ATA Software Features Cisco Small Business ATA Administration Guide 30 1 DHCP Renewal on Timeout SPA2102, SPA3102, and PAP2T voice devices typically operate in a network where a DHCP server assigns IP addresses to the devices. Because IP addresses are a limited resource, the DHCP server periodically renews the device lease on the IP address. Therefore, if an ATA device loses its IP address for any reason, or if some other device on the network is assigned its IP address, the communication between the SIP proxy and the device is either severed or degraded. Whenever an expected SIP res

  • Cisco SPA2102, Environmental Specifications SPA2102 Cisco Small Business ATA Administration Guide 229 D SPA2102 SPA3102 Device Dimensions 3.98 x 3.98 x 1.10 (101 x 101 x 28 mm) W x H x D Unit Weight 5.29 oz (0.15kg) Power 100-240V 50-60Hz (26-34VA), AC Input Certification FCC (Part 15 Class B), CE, ICES-003 Operating Temp 32º to 113º F(0 to 45ºC) Storage Temp -13º to 185ºF (-25 to 85ºC) Operating Humidity 10% to 90% relative humidity, Non-Condensing Storage Humidity 10% to 90% relative humidity, Non-Condensing Device Dimensi

  • Cisco SPA2102, Basic Administration and Configuration Using the Administration Web Server Cisco Small Business ATA Administration Guide 35 2  Advanced Configurations section on page 38 Connecting to the Administration Web Server To access the ATA administration web server, perform the following steps. STEP 1 Start Internet Explorer on a computer that is connected to the same network as the ATA device. STEP 2 Determine the address of the ATA device. a. Connect an analog telephone to the Phone 1 port of the ATA device. (You may not hear a dial tone. Continue to step b.) b. Press on the keypad to access the IVR

  • Cisco SPA2102, ATA Voice Field Reference Line page Cisco Small Business ATA Administration Guide 182 B Disconnect Tone This value is the tone script which describes to the SPA the tone to detect as a disconnect tone. The syntax follows a standard Tone Script with some restrictions. Default value is standard US reorder (fast busy) tone, for 4 seconds. Restrictions:  2 frequency components must be given. If single frequency is desired, the same frequency is used for both  The tone level value is not used. 30 (dBm) should be used for now.  Only 1 segment set is allowed  Total duration of the

  • Basic Administration and Configuration Using the Administration Web Server Cisco Small Business ATA Administration Guide 37 2 Registering to the Service Provider To use VoIP phone service, you must configure your ATA device to the Service Provider. STEP 1 Start Internet Explorer, connect to the administration web server, and choose Admin access with Advanced settings. STEP

  • Cisco SPA2102, Introducing Cisco Small Business Analog Telephone Adapters ATA Software Features Cisco Small Business ATA Administration Guide 27 1 Calling Party Control Calling Party Control (CPC) signals to the called party equipment that the calling party has hung up during a connected call by removing the voltage between the tip and ring momentarily. This feature is useful for auto- answer equipment, which then knows when to disengage. CPC is configured in the Regional, Line, and PSTN Line tabs. See ATA Voice Field Reference, on page 110. Report Generation and Event Logging The ATA device

  • Cisco SPA2102, Introducing Cisco Small Business Analog Telephone Adapters ATA Software Features Cisco Small Business ATA Administration Guide 21 1 NOTE  The IVR functions are accessed by connecting an analog telephone to Phone 1 only.  For proper operation, the service provider should use an Outbound Proxy to forward all voice traffic when the SPA8800 is located behind a router. If necessary, explicit port ranges can be specified for SIP and RTP. ATA Software Features The ATA device is a full featured, fully programmable phone adapter that can be custom provisioned within a wide range of configuration parameters.

  • Cisco SPA2102, Configuring Dial Plans Cisco Small Business ATA Administration Guide 63 4 Interdigit Long Timer (Incomplete Entry Timer) You can think of this timer as the incomplete entry timer. This timer measures the interval between dialed digits. It applies as long as the dialed digits do not match any digit sequences in the dial plan. Unless the user enters another digit within the specified number of seconds, the entry is evaluated as incomplete, and the call is rejected. The default value is 10 seconds. NOTE This section explains how to edit a timer a

  • Cisco SPA2102, ATA Voice Field Reference SIP page Cisco Small Business ATA Administration Guide 123 B SIP User Agent Name User-Agent header used in outbound requests. The default is $VERSION. If empty, the header is not included. Macro expansion of $A to $D corresponding to GPP_A to GPP_D allowed. SIP Server Name Server header used in responses to inbound responses. The default is $VERSION. SIP Reg User Agent Name User-Agent name to be used in a REGISTER request. If this value is not specified, the parameter is also used for the REGISTER request. The default is blank. SIP Accept Language Accept-Language header used. There is no default

  • Cisco SPA2102, ATA Voice Field Reference System page Cisco Small Business ATA Administration Guide 120 B Internet Connection Type section (PAP2T) Optional Network Configuration section (PAP2T) DHCP Enable or disable DHCP. The default is yes. Static IP Static IP address of ATA device, which takes effect if DHCP is disabled. The default is 0.0.0.0. NetMask The NetMask used by ATA device when DHCP is disabled. The default is 255.255.255.0. Gateway The default gateway used by ATA device when DHCP is disabled. The default is 0.0.0.0. Host Name The host name of the ATA device. Domain The network domain of the ATA device. Primary DNS DNS server used by ATA device in addition to DHC

  • Cisco SPA2102, © 2011 Cisco Systems, Inc. All rights reserved. OL-17901-05 Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)

  • Basic Administration and Configuration Using the Administration Web Server Cisco Small Business ATA Administration Guide 36 2 STEP 3 Complete the WAN configuration for DHCP, static IP addressing, or PPPoE. For DHCP: a. Select DHCP from the drop-down menu. b. If you use a cable modem, you may need to configure the MAC Clone Settings. (Contact your ISP for

  • Environmental Specifications SPA8000 Cisco Small Business ATA Administration Guide 230 D SPA8000 SPA8800 Device Dimensions 6.69 x 1.54 x 8.66 (170 x 39 x 220 mm) Unit Weight 2.85 lbs (1.30kg) Power 100-240V 50-60Hz (26-34VA), AC Input Certification FCC (Part 15 Class B), CE, ICES-003, A-Tick Certification, RoH, UL Operating Temp 32º to 113º F(0 to 45ºC) Stora

  • Cisco SPA2102, Troubleshooting Cisco Small Business ATA Administration Guide 225 C Q. Im trying to access the ATA administration web server, but I do not see the login screen. Instead, I see a screen saying, 404 Forbidden. A. If you are using Windows Explorer, perform the following steps until you see the administration web server login screen (Mozilla requires similar steps). 1. Click . Make sure is NOT checked. 2. Press CTRL + F5. This is a hard refresh, which forces Windows Explorer to load new webpages, n

  • Cisco SPA2102, ATA Routing Field Reference WAN Status page Cisco Small Business ATA Administration Guide 104 A Optional Settings section HostName The host name of the ATA device. Domain The network domain of the ATA device. Primary DNS The DNS server that is used by the ATA device. NOTE: When DHCP is enabled, you can enter the IP address of a DNS server in addition to DHCP-supplied DNS servers. When DHCP is disabled, enter the primary DNS server. The default is 0.0.0.0. Secondary DNS Sets the secondary DNS server to take over if problems are discovered with the Primary DNS server. NOTE: When DHCP is enabled, you can e

  • Cisco SPA2102, Configuring Your System for ITSP Interoperability Network Address Translation (NAT) and Voice over IP (VoIP) Cisco Small Business ATA Administration Guide 43 3 NAT Mapping with Session Border Controller It is strongly recommended that you choose an ITSP that supports NAT mapping through a Session Border Controller. With NAT mapping provided by the ITSP, you have more choices in selecting a router. NAT Mapping with SIP-ALG Router If the ITSP network does not provide a Session Border Controller functionality, you can achieve NAT mapping by using a router that has a SIP ALG (Application Layer Gateway). The WRV200 router is recommended for this purpose, although any router with a SI

  • SIP Trunking and Hunt Groups on the SPA8000 Cisco Small Business ATA Administration Guide 71 4 About SIP Trunking The SIP Trunking feature allows a traditional PBX to seamlessly migrate from PSTN service to VoIP service over a broadband link. The SPA8000 offers up to eight telephone lines to the PBX. The SPA8000 offers four trunk groups, numbered T1, T2, T3, and T

  • Cisco SPA2102, ATA Voice Field Reference Trunk Group page (SPA8000) Cisco Small Business ATA Administration Guide 186 B SIP Settings section SIP Transport The TCP choice provides guaranteed delivery, which assures that lost packets are retransmitted. TCP also guarantees that the SIP packages are received in the same order that they were sent. As a result, TCP overcomes the main disadvantages of UDP. In addition, for security reasons, most corporate firewalls block UDP ports. With TCP, new ports do not need to be opened or packets dropped, because

  • Cisco SPA2102, Cisco Small Business ATA Administration Guide 3 Contents Chapter 1: Introducing Cisco Small Business Analog Telephone Adapters 10 Comparison of ATA Devices 11 ATA Connectivity Requirements 14 PAP2T Connectivity 15 SPA2102 Connectivity 16 SPA3102 Connectivity 17 SPA8000 Connectivity 18 SPA8800 Connectivity 20 ATA Software Features 21 Voice Supported Codecs 21 SIP Proxy Redundancy 22 Other ATA Software Features 23 Chapter 2: Basic Administration and Configuration 31 Basic Services and Equipment Required 31 Downloading Firmware 32 Basic Installation and Configuration 32 Upgrading the Firmware for the ATA Device 32 Setting up Your ATA Device 33

  • Cisco SPA2102, ATA Voice Field Reference Regional page Cisco Small Business ATA Administration Guide 142 B Call Back Delay Delay after receiving the first SIP 18x response before declaring the remote end is ringing. If a busy response is received during this time, the ATA device still considers the call as failed and keeps on retrying. The default is 0.5. VMWI Refresh Intvl Interval between VMWI refresh to the CPE. The default is 0.5. Interdigit Long Timer Long timeout between entering digits when dialing. The interdigit timer values are used as defaults when dialing. The Interdigit_Long_Timer is used after any one digit, if all valid matching sequences in the d

  • Cisco SPA2102, Introducing Cisco Small Business Analog Telephone Adapters ATA Connectivity Requirements Cisco Small Business ATA Administration Guide 17 1 SPA3102 Connectivity As shown in the following figure, the SPA3102 has one FXS port (voice line 1). By default, the device on the LAN port is assigned the network address 192.168.0.0 with a subnet mask of 255.255.255.0. If there is a network address conflict with a device on the Ethernet port, the network address of the device on the LAN port is automatically changed to 192.168.1.0. NOTE  The IVR functions are accessed by connecting an analog telephone to Line 1.  For proper operation, the service provid

Related Products and Documents (Adapter):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Kenwood KDC-C719 - CD Changer Instruction manual kenwood/kdc-c719-cd-changer-252.pdf 24 Mar 2023 16
2 Alpine IVA-W203 - 6.5" Touch Screen 2-DIN DVD In-Dash Receiver Owner's manual alpine/iva-w203-6-5-touch-screen-2-din-dvd-in-dash-receiver-CF7.pdf 20 Sep 2023 83 5.32 Mb
3 Field Controls 46298500 Manual  field-controls/46298500-9M6.pdf 21 Aug 2022 8 0.57 Mb
4 Canon imageFORMULA CR-180II Brochure & specs canon/imageformula-cr-180ii-74W.pdf 21 May 2023 16 2.61 Mb
5 TDK EL Series EL0405 Specifications tdk/el-series-el0405-9VP.pdf 10 Jun 2023 3 0.05 Mb
6 pass & seymour WDT-200 Installation instructions pass-seymour/wdt-200-6W6.pdf 20 Sep 2023 3

Similar Resources:

  • brennenstuhl

    SP-230V-4500

    (50 pages)
    Hugo BrennenstuhlGmbH & Co. KGSeestraße 1–372074 TübingenGermanyBedienungsanleitungÜberspannungsschutzadapterDEOperating instructionsOvervoltage protection adaptorGBManual de instruccionesAdaptador de protección contra sobretensiónESGebruiksaanwijzingOverspanningsbeveiligings-adapterNLBruksanvisningÖverspänningsskyddsadapterSE0416862 …
  • Antrax

    MultiBox-LAN

    (28 pages)
    antrax Datentechnik [email protected] - www.antrax.deMultiBox-LAN• LAN interface• watchdog funcionality• relay version• sensor input for temperature and humidity measurement• integrated control panelManual18.02.2011- 1 -Hasenbrink 4, 32052 Herford, Germany Tel. +49 (0) 5221 929660 Fax +49 (0) 5221 9296628 …
  • Belkin

    F2CD007

    (2 pages)
    1. Disclaimer The purchase and use of the Belkin AV360 Mini DisplayPort Converter (the Converter) is for indoor application only. The Belkin Converter is not intended for outdoor use as critical damage to hardware, internal components, and nonperformance may occur. 1. Clause de non-responsabilitéLe convertisseur Mini DisplayPort AV360 de Belkin (le converti …
  • Altronix

    Pace1PRMT

    (4 pages)
    Overview:Pace1PRMT is a long range Ethernet adapter kit that transmits data at 100Mbps full duplex and power via a single twisted pair (UTP) or CAT5e or higher cable in a PoE(+) compliant format. The Pace1PRM receiver is powered via a PoE midspan, such as the Altronix Netway series, or by an endspan. The receiver passes the PoE(+) compliant power over the ca …
  • Veracity

    HIGHWIRE Powerstar Duo VHW-HWPS-C2

    (2 pages)
    VHW-HWPS-C2QUICK START GUIDE2 PORT ETHERNET OVER COAX ADAPTORLED FUNCTIONRJ45 Yellow On = link Blink = activityRJ45 Green On = POE detected and enabledRJ45 Ethernet 10/100Base-Tx and POE connectors (auto speed, duplex, crossover, POE/POE Plus)CONNECTIONS & LEDSLED COAX LINKCOAX NET COAX PWR(Power)POE POWERBUDGETFUNCTIONCoax dataconn …
  • Jabra

    GN Ellipse 2.4

    (2 pages)
    Base RemoteDimensions (inches)6.0 H x 4.0 W x 0.8 D 4.0 H x 2.5 W x 1.0 DWeight 6.2 oz. 3.3 oz.Power Supply 7.5 V DC, 500 mA max. 3.6 V rechargeable NiMH, 550 mAH batteryTransmit Frequency 2.4 GHz (same for base and remote)Baseband Modulation ADPCMRF Modulation FDMABattery Operation Time 12 hours (continuous use ‘on-line’)80 hours (continuous use ‘off- …

Comments, Questions and Opinions: