Cisco Telepresence MX800 Replacement Manual

Text of Cisco Telepresence MX800 User Guide:

• D15327.01 MX800 Dual Replacement Guide, MAY 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved. 22 Cisco TelePresence MX800 Dual Replacement Guide Replace dual camera module (page 7 of 7) Step 7: Pull out camera module Re-assembly: In order to install the new camera module, follow the steps in reversed order. Gently pull out the camera mo

• Cisco Telepresence MX800, D15327.01 MX800 Dual Replacement Guide, MAY 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved. 1 Cisco TelePresence MX800 Dual Replacement Guide Replacement guide for Cisco TelePresence MX800 Dual

• Cisco Telepresence MX800, D15327.01 MX800 Dual Replacement Guide, MAY 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved. 41 Cisco TelePresence MX800 Dual Replacement Guide Replace monitor (wall mounted) (page 5 of 8) Step 7: Remove all cables From codec connector panel Power From codec, loudspeakers and left monitor From PoE injector From codec, camera, loudspeakers and right monitor All cables that were shipped with the system remain in your property and should not be returned to the supplier. You will not receive new

• D15327.01 MX800 Dual Replacement Guide, MAY 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved. 45 Cisco TelePresence MX800 Dual Replacement Guide Appendix Part numbers for spare parts ..................................................................................46

• Cisco Telepresence MX800, D15327.01 MX800 Dual Replacement Guide, MAY 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved. 6 Cisco TelePresence MX800 Dual Replacement Guide Grilles and covers Replace speaker grille and lower grille ...................................................................... 7 Replace floor stand covers ........................................................................................8 Replace side covers ...............................................................

• Cisco Telepresence MX800, D15327.01 MX800 Dual Replacement Guide, MAY 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved. 29 Cisco TelePresence MX800 Dual Replacement Guide Replace PoE injector (page 2 of 2) Step 2: Remove PoE injector Disconnect cables: 1 × Power (top) 2 × RJ45 (bottom), Ethernet and Touch 10 user interface. Remove PoE injector.Remove screws and washers. 2 × M3x8 (pan), Torx T10 Re-assembly: In order to install the new PoE injector, follow all the steps in reverse order. 2a 2b 2c

• Cisco Telepresence MX800, D15327.01 MX800 Dual Replacement Guide, MAY 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved. 43 Cisco TelePresence MX800 Dual Replacement Guide Replace monitor (wall mounted) (page 7 of 8) Step 9: Lift monitor Loosen the wing nuts on both sides. They are accessed from the sides of the monitor. Lift up the monitor and place it in the original shipping packaging. Before moving the monitor Plan ahead where to put down the monitor. Ideally, place it in the original sh

• Cisco Telepresence MX800, D15327.01 MX800 Dual Replacement Guide, MAY 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved. 38 Cisco TelePresence MX800 Dual Replacement Guide Replace monitor (wall mounted) (page 2 of 8) Step 4: Remove joining bracket Pull up the lever. Remove the joining bracket from the channel. 5 × M6x12 (pan) 4a 4b 4c

• Cisco Telepresence MX800, D15327.01 MX800 Dual Replacement Guide, MAY 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved. 2 Cisco TelePresence MX800 Dual Replacement Guide Table of contents Introduction ........................................................................................................... 3 Grilles and covers ................................................................................................. 6 Replace speaker grille and lower grille ..................................

• Cisco Telepresence MX800, D15327.01 MX800 Dual Replacement Guide, MAY 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved. 27 Cisco TelePresence MX800 Dual Replacement Guide Replace codec (page 4 of 4) Step 4: Pull out codec using velcro strap at top Re-assembly: In order to install the new codec, follow all the steps in reverse order. The codec is mounted in a power dock. Pull firmly to get it out.

• Cisco Telepresence MX800, D15327.01 MX800 Dual Replacement Guide, MAY 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved. 39 Cisco TelePresence MX800 Dual Replacement Guide Replace monitor (wall mounted) (page 3 of 8) Step 5: Install support handles First remove the support handles from your replacement monitor as illustrated. Then mount the handles on the monitor you want to replace. This is neccessary in order to safely lift the monitor. Unscrew the screws (4 × M4x8, two on each handle) and remove the two suppo

• Cisco Telepresence MX800, D15327.01 MX800 Dual Replacement Guide, MAY 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved. 42 Cisco TelePresence MX800 Dual Replacement Guide Replace monitor (wall mounted) (page 6 of 8) Step 8: Unscrew monitor screws and disconnect power cable Disconnect the power cable between the two monitors. 4 × M6x12 (countersunk), Allen key, 4 mm 4 × M6x90 (countersunk), Allen key, 4 mm M6x90

• Cisco Telepresence MX800, D15327.01 MX800 Dual Replacement Guide, MAY 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved. 21 Cisco TelePresence MX800 Dual Replacement Guide 4 × M4x8 (pan), Allen key 2.5 mm Remove four screws. Remove brackets. Replace dual camera module (page 6 of 7) Step 6: Remove brackets 6a 6b

• Cisco Telepresence MX800, D15327.01 MX800 Dual Replacement Guide, MAY 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved. 33 Cisco TelePresence MX800 Dual Replacement Guide Replace monitor (mounted on a stand) (page 4 of 7) Step 6: Install support handles on the monitor to be replaced First remove the support handles from your replacement monitor as illustrated. Then mount the handles on the monitor you want to replace. This is neccessary in order to safely lift the monitor. Unscrew the screws (4 × M4x8, two on each handle) and remove the two support handles from the replacement monitor. Unscrew the screws (2 × M4x8, one on each bracket) and remove the

• Cisco Telepresence MX800, D15327.01 MX800 Dual Replacement Guide, MAY 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved. 9 Cisco TelePresence MX800 Dual Replacement Guide Spare part: • CTS-MX800-MON-SCV= Replace side covers The covers are fastened with magnets. Pull out gently to remove the covers. Re-assembly: The covers snap to the magnets when put back in place.

• Cisco Telepresence MX800, D15327.01 MX800 Dual Replacement Guide, MAY 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved. 19 Cisco TelePresence MX800 Dual Replacement Guide Left camera board 3 DAISY CHAIN VISCA Camera assembly board 2 1 2 1 2 1 2 1 Right camera board 3 DAISY CHAIN VISCA Replace dual camera module (page 4 of 7) Step 4: Unplug camera cables Only remove the cables shown here The other cables are internal to the dual camera module and should not be disconnected.

• D15327.01 MX800 Dual Replacement Guide, MAY 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved. 30 Cisco TelePresence MX800 Dual Replacement Guide Replace monitor (mounted on a stand) Spare parts: • Left monitor: CTS-MX800-MON-L-D= • Right monitor: CTS-MX800-MON-R-D= The illustrations provided show how to replace the right moni

• D15327.01 MX800 Dual Replacement Guide, MAY 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved. 28 Cisco TelePresence MX800 Dual Replacement Guide Replace PoE injector Step 1: Remove right side cover Spare part: • CTS-PWR-AIR-INJ5= The side cover is fastened with magnets. Pull out gently and set aside. (page 1 of 2)

• Cisco Telepresence MX800, D15327.01 MX800 Dual Replacement Guide, MAY 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved. 20 Cisco TelePresence MX800 Dual Replacement Guide Replace dual camera module (page 5 of 7) Step 5: Unscrew camera screws 4 × M4x8 (pan), Allen key, 2.5 mm Remove 4 screws from the front. 2 × M4x8 (pan), Allen key, 2.5 mm Remove lower screws. 5a 5b

• Cisco Telepresence MX800, D15327.01 MX800 Dual Replacement Guide, MAY 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved. 37 Cisco TelePresence MX800 Dual Replacement Guide Replace monitor (wall mounted) Spare parts: • Left monitor: CTS-MX800-MON-L-D= • Right monitor: CTS-MX800-MON-R-D= The illustrations provided show how to replace the right monitor. Similar steps should be taken on the left monitor, when replacing the left monitor. Step 1: Remove speaker grille, lower grille, loudspeakers and camera Follow the steps described in “Replace dual camera module” on page 16 to p

• Cisco Telepresence MX800, D15327.01 MX800 Dual Replacement Guide, MAY 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved. 15 Cisco TelePresence MX800 Dual Replacement Guide Replace a loudspeaker (page 2 of 2) Step 2: Remove the loudspeaker The same procedure applies for loudspeakers in all positions. Re-assembly: In order to install the new loudspeaker, follow the steps in reversed order. Pull loudspeaker 10-15 cm (4-6 inch) out. Unplug the cable from the connector on the back of the loudspeaker. Remove screw. PT4x10, Torx T20 2a 2b 2c

More Instructions:

	Cisco Telepresence MX800 Installation manual 03-08-2023 29	DOWNLOAD
	Cisco Telepresence MX800 Quick reference manual 09-11-2023 2	DOWNLOAD
	Cisco Telepresence MX800 Reference manual 09-10-2023 182	DOWNLOAD
	Cisco Telepresence MX800 Replacement manual 26-07-2023 46	DOWNLOAD

Related Products and Documents (Digital Presenters):

Comparable Devices:

Similar Resources:

• Steren COM-5602 (2 pages) COM-5602COMPUTACIÓNV0.0 1215vManual de instruccionesControl inalámbrico de diapositivas con función air mouse1ON/OFF2345678910AIMPORTANTELa información que se muestra en este manual sirve únicamente como referencia sobre el producto. Debido a actualizaciones pueden existir diferencias.Por favor, consulte nuestra página web (www.steren.com) paraobtener …

• Cisco TelePresence MX200G2 (45 pages) 1In-Room Control on Touch10 for Cisco TelePresence MX200 G2, MX300 G2, MX700, MX800, SX10, SX20, SX80Collaboration Endpoint software version CE8.2D15358.02 - JULY 2016www.cisco.com © 2016 Cisco Systems, Inc. All rights reserved. In-Room Control on Touch10User Interface ExtensionsCisco TelePresence MX200 G2, MX300 G2, MX700, MX800, SX10, SX20, S …

• Turning Technologies QT2 (2 pages) Numeric Response - Numeric Response questions require a numeric value to be entered. Use the number pad to enter your answer and press OK to submit your answer choice.CHANGING THE CHANNELUse the steps below to manually set the channel or use the Find Channels function to nd a receiver within range.WARNING: If the lock symbol appears next to the …

• Avex EASY PRESENTER 3065 (2 pages) EASY PRESENTER 3065 Manual 1. CONNECTION AND OPERATION The Easy Presenter is operated using the control panel on the front. To turn the system on, simply press ‘POWER ON’. Next, connect the cable to the laptop and select the appropriate source. The diagram opposite shows which source is connected where. The connections and cables are situated at the …

• Samsung SDP-760 (2 pages) SDP-760Full HD Compact Digital Presenter• 3Megapixels for superior quality image display• Native Full HD (1920 x 1080) at 30fps with no latency• Digital 16x zoom & Digital Image Rotation • Compact footprint with flexible arm• User scalable display outputs from XGA to Full HD at 16 : 9Portable, Compact Digital Presenter www.samsungpresen …

• Elmo TX-1 (36 pages) 㻌㻌䠲䠥䠯䠱䠝䠨㻌 䠬䠮䠡䠯䠡䠪䠰䠡䠮㻌䠰䠴㻙㻝㻌 ࢡ࢖ࢵࢡࢫࢱ࣮ࢺ࢞࢖ࢻ Quick Start Guide Make sure to read the ͆IMPORTANT SAFEGUARDS͇ in this guide before using this product.For details about the operations of this product, refer to the instruction manual. 〇ရ䛾௙ᵝ䞉ྲྀᢅㄝ� …

Comments, Questions and Opinions: