CISEYE CIP-750 Instruction Manual

Text of CISEYE CIP-750 User Guide:

• CISEYE CIP-750, Precautions Adjust only those controls specified in the operating instructions. Improper adjustment of other controls may cause damage to the unit. Use of controls or adjustments, or performance of procedures other than those specified, may result in hazardous radiation exposure. • Do not point camera at any source of bright light. If the object contain very bright areas, bright vertical or horizontal lines may appear on the screen. This is called smear, a phenomenon, which often occurs with

• CISEYE CIP-750, 4 NETWORK SETUP Case C : Static(Fixed) IP [Dedicated line directly to the IP Dome Camera] Configure your IP Dome Camera's TCP/IP properties as follows : 󼎊 Network Type 󼎊 Internet Address STATIC A static IP address received from your ISP, such as 24.107.88.125 [Example]. You need to assign the IP Dome Camera an IP address, just as you would assign a PC. i 󼎊 Web Server Port 󼎊 Control Server Port 󼎊 Video Server Port 󼎊 Audio Transmit Server Port󼎊 󼎊 Audio Receive Server Port󼎊 8888 7777 7778 7779 7780 Do NOT use the

• CISEYE CIP-750, • Start/End Input IP Dome Camera Web Server Port and Video Server Port. Start should be same as End. Both of Web Server Port and Video Server Port should be Added. • Application Input IP Dome Camera name. • Protocol • IP Address • Enabled Select "TCP" in Protocol option. Input IP Dome Camera IP Address. Check the square. Input port numbers in "Port Range" as below and click [Save Setting] button. Both of Web Server Port and Video Server Port should be added. The example is as below: m 󼎊 For Netgear RP614 routers Input http://192.168.0.1 in address bar o

• Reset its system configuration to the factory defaults. Note: After initializing, all information should be deleted. Please re-consider before initializing. Re-boots IP Dome Camera. Default Set Tool Rebooting Tool 6 ADMIN TOOL 39/52CISEYE Indoor IP Dome Camera Users Manual

• CISEYE CIP-750, TCP/IP Tool 󼎊 Internet Address Input a value to assign an IP address to the IP Dome Camera. 󼎊 Subnet Mask Input a value to assign a subnet mask to the IP Dome Camera. 󼎊 Default Gateway Input the IP address of the default gateway. 󼎊 Primary DNS Server Input the IP address of an ISPs DNS server.' 󼎊 Network Type Select a Static or Dynamic address scheme that is used by the Internet Service Provider(not the addressing scheme used by a personal router). 󼎊 Web Server Port 󼎊 Video Server Port 󼎊 Control Server Port 󼎊 Audio Transmit Server Port󼎊 󼎊 Audio

• CISEYE CIP-750, 4 NETWORK SETUP Case A : Dynamic IP or PPPoE + Personal Router [Most SOHO] Configure your IP Dome Camera's TCP/IP properties as follows : 󼎊 Network Type 󼎊 Internet Address STATIC(even though you have Dynamic IP, use STATIC on the IP Dome Camera). A private IP address such as 192.168.0.200 [Example]. You need to assign the IP Dome Camera an IP address, just as you would assign a PC. The IP address you assign must be unique to your network as well as match your network. For information how to choose a unique IP and match you

• CISEYE CIP-750, Motion Detection Tool 󼎊 Detection Action Set up the reaction of IP Dome Camera when motion detected. Alert Sound Out 1 ~ 4 : Audio Out through the Audio out jack of IP Dome Camera. : Out 1 ~ 4 : Select output relay numbers in the Sensor Alarm I/O module connected with IP Dome Camera.: 6 ADMIN TOOL 33/52CISEYE Indoor IP Dome Camera Users Manual

• CISEYE CIP-750, 󼎊 Simplified Setting and Advanced Setting 󼎊 󼎊 󼎊 Encoding Video Mode󼎊 󼎊 Quality 󼎊 Bit Rate In fact, these two has same concepts. However, the Simplified Setting is described in terms of simple and easy expressions to help nonprofessional users. If you are professional and want to set delicately, choose Advanced Setting. In Quality Basis mode, you can select video encoding and streaming in the viewpoint of video quality rather than bandwidth occupied. In this case, Bandwidth can be traded off to meet your video quality requirement under some network environments. (This mode is same as VBR mode in Advanced setting) In Bandwidth Basis mode,

• CISEYE CIP-750, OSD(On Screen Display) : Click this icon to display the captions. Click this icon to save an image. Shows current number of users connected as: [Current number of users connected/maximum number of users connected]. Use these arrows to control a PTZ device. Speed option for IP Dome Camera or PTZ devices. Zoom, Focus, and Iris functions for PTZ devices that support the listed functions. Presets used by some PTZ devices that support preset directions and zoom. Pattern, Swing and Group functions for the Pan/Tilt camera that support the listed functions. This button enables

• CISEYE CIP-750, Cable DC12V I/O TERMINAL BNC (VIDEO) AUDIO OUT AUDIO IN NETWORK CROSS Product Components 󼎊 Product & Accessories Main Body Software CD Screw Power Adapter NOTICE! If equipment appears to have been damaged during shipment, repack it in the original pakaging and notify the shipping agent or supplier. 2 INTRODUCTION 8/52CISEYE Indoor IP Dome Camera Users Manual

• CISEYE CIP-750, This function is used to email the specified email recipient and notify that individual of the IP address/web port number used to access the IP Dome Camera. This email function is only activates on power-on reset time of IP Dome Camera. SMTP Tool 󼎊 SMTP Server 󼎊 User Name 󼎊 User Password 󼎊 Send E-Mail box 󼎊 SMTP requires auth. 󼎊 From 󼎊 To Enter an SMTP server to send email. Input user name used for SMTP authentification to access the mail server. Input the password used for SMTP authentification to access the mail server. If this check box is set to on, email function is enabled. Check this b

• CISEYE CIP-750, After correctly forwarding the Web Server Port , Video Server Port, Control Server Port and two Audio Ports through your router(if applicable), you may then install the IP Dome Camera in a proper location. Starting Network Camera Locate the serial number located on the label attached to the bottom of the IP Dome Camera, you will need this for DDNS registration. Connect the IP Dome Camera to your router or cable/DSL modem(per your network scenario) via a Cat5/5e UTP Ethernet network cable. Supply power to the IP Dome Camera. After 50 seconds, verify the IP Dome Camera indicators: After configuring Port Forwarding on your router(if necessary), you may then access your IP Dome Camera on y

• CISEYE CIP-750, The IP Dome Camera utilizes five TCP ports - a Web Server Port for utilizing Internet Explorer, a Video Server Port, a Control Server Port, Audio ports. A Web Server Port is for utilizing Internet Explorer, a Video Server port is to support the streaming video, and a Control Server Port is to transmit to control command. Also Audio Port are to transmit and to receive Audio data. If this IP Dome Camera will be directly attached to a cable/DSL/Broadband modem or has been assigned a static IP from your ISP, then leave

• CISEYE CIP-750, 4 NETWORK SETUP This is the same site you will register with later to utilize our DDNS service. i 󼎊 DDNS Server Use the DDNS server. Case E : PPPoE + DSL Modem [Connected directly to the IP Dome Camera] Configure your IP Dome Camera's TCP/IP properties as follows : 󼎊 Network Type 󼎊 User ID 󼎊 User Password PPPoE Use the User ID or Username you received from your ISP for this direct connection. Use the Password you received from your ISP for this direct connection. 󼎊 Web Server Port 80 [default]. You m

• CISEYE CIP-750, 󼎊 Web Server Port 80 [default]. You may select any number between 1025 ~ 30000. i 󼎊 Default Gateway 24.107.88.113 [Example]. 󼎊 Subnet Mask Subnet mask assigned from your ISP, such as 255.255.255.240 [Example]. Use the assigned default gateway from your ISP. i This is the same site you will register with later to utilize our DDNS service. i 󼎊 Primary DNS Server Use the 1st DNS Server from Assigned IP Addresses from My ISP" ". If you did not receive any IP addresses from your ISP, please contact them and acquire the IP address of their DNS server. i 󼎊 DDNS Server Use the DDNS server. 󼎊 Control Server Port 󼎊 Video Server Port 󼎊 Audio Transmit

• • Destination Select LAN in Interface option. Input IP Dome Camera IP Address in IP Range Start / End. Select TCP in Protocol option. Input IP Dome Camera Web Server Port in the both of Port Range. The port number of the former blank should be same as that of the latter blank in Port Range. " " " " • Schedule Select "Always". n o p If 'Set

• CISEYE CIP-750, Initial Setup via a Crossover Cable This section provides a guide on how to connect the IP Dome Camera to your PC/laptop for initial setup. Please follow the instructions in the order they appear, without skipping steps. Do not supply power to the IP Dome Camera, until instructed. In order to access the IP Dome Cameras firmware you will need to connect the IP Dome Camera directly to a PC or laptop computer via the supplied crossover cable. ' Before you begin, you must determine the current network/INTERNET(TCP/IP) settings on the PC or laptop you plan to setup the IP Dome Camera. Jot down your entries below for quick Reference. • IP Address

• Motion Detection Tab This button activates or stops motion detection. Detection Area setting below must be done in advance." " This button activates or stops motion detection target area setup mode. If you click this button, you will see the green grids on the screen. To assign the target area, click the corresponding square on there screen. The color of the square will be changed.

• CISEYE CIP-750, Cabling 󼎊 DC Power Plug Cable 󼎊 Video BNC Connector Cable 󼎊 Audio In Female RCA Connector Cable 󼎊 Audio Out Male RCA Connector Cable 󼎊 Network CAT-5 Cable 󼎊 I/O Terminal Cable Connect with Power Adapter([email protected]) to supply power to IP Camera. Connect with TV, monitor or other video devices for video images showing. Connect with microphone, audio pick up box or other audio source devices for sound surveillance and voice talk function. Connect with speaker or other audio playing devices for voice talk function. Connect with router, switch, modem or other Ethernet devices for IP Camera

• CISEYE CIP-750, Date & Time Tool 󼎊 Current Date/Time 󼎊 New Date/Time It shows the current Date/Time setting of IP Dome Camera. Select the method of Date/Time setting. Date/Time can be set by local computer or time server or manual. 6 ADMIN TOOL 36/52CISEYE Indoor IP Dome Camera Users Manual

• CISEYE CIP-750, This section is designed to familiarize you with the main interface of the IP Dome Camera. Displaying the OSD and Digital Zoom are only taking place on the local machine, not on the IP Dome Camera itself. To make global changes on the IP Dome Camera and its video, you must login as an administrator. Web Viewer Screen 󼎊 General Tab Camera Image Display. OSD - Camera Name/Date/Time. OSD - This indicator displayed represents the function caption when a specific user logs on. • G = Guest User :

• CISEYE CIP-750, This section is provided to familiarize the user with the administration tools. Intuitive options are not explained in detail. All the changes on Administration Tools take effect immediately. These settings will be global, affecting the view of all users currently logged on. However, OSD items selections are effective only after you refresh the viewer windows or restart the internet Explorer. All settings are always saved in the video server even when you close the viewer program or you turn off the Power of the video server. If you lost your password, you must press the reset button to return all setting to its factory defaults. Video Tool 󼎊 Camera Na

• CAUTION! Never supply power via the Ethernet connection(PoE) when power is supplied via the power connector. Video Network Speaker Router Power Microphone GND DC12V / 1A Siren Sensor PC Desktop 12/52CISEYE Indoor IP Dome Camera Users Manual 3 INSTALLATION

• CISEYE CIP-750, 󼎊 Can I use the Network Video Server on my dial-up Internet connection? 󼎊 Im accessing my IP Dome Camera remotely over the Internet and the video stream is choppy, is this normal?' No, we recommend a high-speed broadband connection of at least 128Kb/sec. Yes. The frames per second received remotely are determined by your bandwidth capabilities both at your site where the IP Dome Camera is installed and your remote location. The lower of the two sites will determine how fast your video stream is received. It is recommended to have at least a 256Kb/sec upstream connection from the site where

• CISEYE CIP-750, 󼎊 Web Server Port 󼎊 Control Server Port 󼎊 Video Server Port 󼎊 Audio Transmit Server Port󼎊 󼎊 Audio Receive Server Port󼎊 8888 7777 7778 7779 7780 Do NOT use the default port 80, you must change this number. You may select any number between 1025 ~ 30000. i i You may select any number between 1025 ~ 30000. i You may select any number between 1025 ~ 30000. i You may select any number between 1025 ~ 30000. i You may select any number between 1025 ~ 30000. i 4 NETWORK SETUP 19/52CISEYE Indoor IP Dome Camera Users Manual

• CISEYE CIP-750, 4 NETWORK SETUP Case B : Static(Fixed) IP + Personal Router [Efficient] Configure your IP Dome Camera's TCP/IP properties as follows : 󼎊 Network Type 󼎊 Internet Address STATIC A private IP address such as 192.168.0.200 [Example]. You need to assign the IP Dome Camera an IP address, just as you would assign a PC. The IP address you assign must be unique to your network as well as match your network. For information how to choose a unique IP and match your network please read the FAQ. The IP address you assign the IP Dome Camera must be a private IP. F

Related Products and Documents (Security Camera):

Comparable Devices:

Similar Resources:

• Security Labs SLC-170C (8 pages) Model SLC-170C Weatherproof Pan/Tilt 22X Optical Zoom Dome Owner’s Manual 15540 Herriman Blvd. Noblesville, IN 46060 - Customer Support 1-800-774-0284 www.security-labs.com …

• Eaton Crouse-hinds series (8 pages) High Amperage Solar Combiner Box CCBInstallation & Maintenance InformationSAVE THESE INSTRUCTIONS FOR FUTURE REFERENCEIF 1710IF 1710 • 10/15 Copyright © 2015, Eaton’s Crouse-Hinds Division Page 1SAVE THESE INSTRUCTIONS - This manual contains important instructions for Solar Combiner Boxes that shall be followed during installation and maintenance …

• Samsung SNP-5300 (2 pages) www.samsungipolis.comSNP-5300/5300HThe SNP-5300/5300H is a PTZ dome camera that provides 30x zoom in HD resolution. It enables monitoring of a scene further away from the camera in more detail and with a higher image quality. In addition, its WDR (Wide Dynamic Range) function automatically produces clear images under strong backlight environments.The SNP-530 …

• Vicon VC-632 (30 pages) XX168-10-00 VC-632 AND VC-632C DAY/NIGHTCOLOR CAMERAS Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed to be used in lif …

• Sanyo VCC-HD2100 - Full HD 1080p Network Camera (7 pages) SANYO VCC-HD2100 1080p 4 MEGAPIXEL COLOR CS BOX CAMERAProject Name/Project Number 28 23 29 - 14 Video Surveillance Remote Devices and Sensors SanyoCompanyDecember,2009SecurityProductsDivision 21605PlummerStreetChatsworth,CA91311Phone:888.818.2597Fax:818.717.27162239180 …

• Avtech AVP325 (33 pages) 317Z P325_P325A_Manual_V1.3 UUsseerr MMaannuuaall Please read instructions thoroughly before operation and retain it for future reference. The image shown above may differ from the actual product appearance. …

Comments, Questions and Opinions: