Dale Power Solutions E201 Operation & User’s Manual

Text of Dale Power Solutions E201 User Guide:

• Dale Power Solutions Ltd User Manual ………………………………………………………………………………………………………… 11 Operation Working modes The UPS has four distinct modes of operation: ■ On-line mode ■ Bypass mode ■ Battery mode ■ ECO mode Each operating mode is described below. On-Line mode This is the defa

• Dale Power Solutions E201, Dale Power Solutions Ltd User Manual ………………………………………………………………………………………………………… 23 Opto-coupler input specifications (used for remote shutdown): Parameter Value Reverse voltage (V R ) 6 V d.c. Forward input voltage 30 V d.c. max., 5 to 12 V d.c. typical Forward current 80 mA max., 16 mA typical Pulse forward current (I FP ) 1 A (100 μs pulse, 100 pps) To use the 9 pin D-type connector: 1. On the UPS, plug your signal cable into the D-type connector and secure with the scre

• Dale Power Solutions E201, Dale Power Solutions Ltd User Manual 18 ………………………………………………………………………………………………………… Fault mode In fault mode the UPS cuts off the output or switches to bypass mode, and sounds the buzzer. The warning LED is lit and the display shows a fault code. A list of fault codes is shown on page 26. In this mode you can: ■ Mute the buzzer temporarily until the fault is corrected. ■ Turn off the UPS.

• Dale Power Solutions E201, Dale Power Solutions Ltd User Manual 4 ………………………………………………………………………………………………………… Troubleshooting .................................................................................................................................. 20 Appendix 1 Signals options ................................................................................................................ 21 RS232 serial port ..........................................................................................................................

• Dale Power Solutions E201, Dale Power Solutions Ltd User Manual ………………………………………………………………………………………………………… 27 Appendix 5 LED indicator status No Working status Beeps Comments 1 On-line mode Normal voltage None High/low mains, in battery mode Every 4 s 2 ECO mode Normal voltage None High/low mains, in battery mode Every 4 s 3 Battery mode Normal voltage Every 4 s Battery voltage abnormal

• Dale Power Solutions Ltd User Manual 12 ………………………………………………………………………………………………………… Front panel controls and indicators The front panel controls and indicators are shown in Figure 4. Using the buttons, LEDs and the menu structure displayed on the LCD panel you can: ■ Check the statu

• Dale Power Solutions E201, Dale Power Solutions Ltd User Manual ………………………………………………………………………………………………………… 19 Maintenance E200 series units use sealed lead acid, maintenance free batteries and require minimum maintenance in general. To keep the batteries fully charged and in good condition, ensure the UPS is plugged into the mains at all times. The UPS battery charger guards against over-charging and deep discharge. Fan At normal room ambient temperature the fans will operate continuously for 20,000 to 40,000 hours. Increased ambient temperatures wi

• Dale Power Solutions Ltd User Manual 22 ………………………………………………………………………………………………………… Relay card (advanced monitoring and control) If your unit has been specified and fitted with the optional relay card (located in the Intelligent Slot on the rear panel) you have access to more advanced monitoring an

• Dale Power Solutions E201, Dale Power Solutions Ltd User Manual 8 ………………………………………………………………………………………………………… Installation Siting considerations Before unpacking and installing the unit, consider the following: ■ DO NOT expose the UPS to high temperatures, water ingress, flammable or corrosive gas, dust, direct sunlight or explosives. ■ Locate the UPS indoors on a level surface as close as possible to the equipment it will be powering to minimise cable voltage drops. Allow enough spare cable to move the UPS and access the rear and side panels during servicing. ■ Maintain a gap of at least 20 cm between the ventilati

• Dale Power Solutions E201, Dale Power Solutions Ltd User Manual 6 ………………………………………………………………………………………………………… Product description Applications This UPS series provides reliable AC backup power to various types of equipment, for example computer centres, network management centres, auto control systems, and telecommunication systems. Product range The following table lists the models available in the E200 series. Models with an E suffix are designed for operation with an external battery.

• Dale Power Solutions E201, Dale Power Solutions Ltd User Manual ………………………………………………………………………………………………………… 25 Output Efficiency in battery mode ≥84% Efficiency in ECO mode ≥94% Safety and EMC Safety IEC62040-1 GB4943 Isolation resistance >2 MΩ (500 V d.c.) Isolation voltage 2,820 V d.c., <3.5mA 1 min EMC Conduction: IEC 62040-2 Radiation: IEC 62040-2 Harmonic: IEC 62040-2 EMS IEC 62040-2 Environment Op

• Dale Power Solutions E201, Dale Power Solutions Ltd User Manual ………………………………………………………………………………………………………… 9 Rear panel layout Figure 2 and Figure 3 show the rear panel connections for the two sizes of UPS. Figure 2 Rear panel layout (1 kVA unit) Figure 3 Rear panel layout (2/3 kVA units) Surge protected network connection Surge protected network connection

• Dale Power Solutions E201, Dale Power Solutions Ltd User Manual 10 ………………………………………………………………………………………………………… Unpacking the UPS 1. Unpack the UPS and check that it has not been damaged during transportation. If damage has occurred or parts are missing, inform Dale Power Solutions Ltd immediately. 2. Remove and retain the documentation, CD and leads from inside the box. 3. Dispose of packets of desiccant correctly. Wiring the UPS Before connecting the UPS, read the siting con

• Dale Power Solutions E201, Dale Power Solutions Ltd User Manual 2 ………………………………………………………………………………………………………… Dale Power Solutions Ltd own the copyright to this document, which may not be copied, reproduced or disclosed to a third party without written permission. Dale Power Solutions Ltd reserves the right to make changes in specification without notice or liability. All information is subject to Dale Power Solutions Ltd own data and is considered accurate at time of publishing.

• Dale Power Solutions E201, Dale Power Solutions Ltd User Manual ………………………………………………………………………………………………………… 5 Safety WARNING! THIS UPS IS CLASSED AS PLUGGABLE EQUIPMENT INTENDED FOR USER INSTALLATION. BEFORE ATTEMPTING TO INSTALL AND COMMISSION THE UPS CAREFULLY READ THIS USER MANUAL. KEEP THIS MANUAL NEXT TO THE UPS FOR FUTURE REFERENCE. There are dangerous voltages and high temperatures inside the UPS. During installation, operation and maintenance please abide by local safety instruc

• Dale Power Solutions E201, Dale Power Solutions Ltd User Manual 16 ………………………………………………………………………………………………………… 3. Press for more than 0.5 s but less than 2 s. The following is displayed. 4. Press for more than 0.5 s but less than 2 s. OFF stops flashing. 5. Press or to display ON, which flashes. 6. Press for more than 0.5 s but less than 2 s. ON stops flashing. 7. Press for more than 2 s. To disable switch to bypass mode: ■ Use the procedure above and select OFF instead of ON. Output voltage level To change the

• Dale Power Solutions Ltd User Manual 26 ………………………………………………………………………………………………………… Appendix 3 Optional equipment The following items are available as options for the UPS: ■ Extension battery box ■ Dry contact relay card ■ SNMP card ■ Battery MCB box ■ Bypass pa

• Dale Power Solutions E201, Dale Power Solutions Ltd User Manual 20 ………………………………………………………………………………………………………… Function check Perform a self test every 6 months as described on page 14. Troubleshooting Before contacting your distributor, try to solve your problem using the information in the following table. If you need to contact your distributor make sure you have the model number and serial number of your UPS. Problem description Probable causes Solution The INPUT letters on LCD display flashes Mains live and neutral connect

• Dale Power Solutions E201, Dale Power Solutions Ltd User Manual ………………………………………………………………………………………………………… 3 Contents Safety..................................................................................................................................................... 5 EMC .................................................................................................................................................... 5 Warning symbols .................................................................

• Dale Power Solutions E201, Dale Power Solutions Ltd User Manual ………………………………………………………………………………………………………… 7 System block diagram A functional block diagram representing the UPS is shown in Figure 1. Power is delivered to the output via one of these three paths; a) via the bypass, b) directly through the AC/DC converter and inverter, or c) from the battery via the DC/DC converter and inverter. In normal operation you can choose either path a) or b). In cases where it is not possible to meet the required hold up time with an internal battery, an E suffix unit with an external battery in place of the internal battery can b

• Dale Power Solutions E201, Dale Power Solutions Ltd User Manual 24 ………………………………………………………………………………………………………… Appendix 2 Specifications Electrical Model E201, E201E E202, E202E E203, E203E Capacity 700 W / 1000 VA 1400 W / 2000 VA 2100 W / 3000 VA Input Input type Single phase (L, N and E) Power factor ≥0.98 Voltage range 109 V a.c. to 310 V a.c. Rated frequency 45 to 65 Hz ECO range Setting output voltage ±20 V a.c. Bypass voltage range 186 V a.c. to 252 V a.c. Current h

• Dale Power Solutions E201, Dale Power Solutions Ltd Salter Road, Eastfield Industrial Estate, Scarborough, North Yorkshire, YO11 3DU, UK [email protected] | www.dalepowersolutions.com | +44 (0) 1723 583511 S5264FU01 Rev 3 Dale Power Solutions Ltd User Manual E200 Series UPS E201(E) E202(E) E203(E)

• Dale Power Solutions Ltd User Manual ………………………………………………………………………………………………………… 13 LCD display The LCD display comprises a battery capacity graphics section, a fan status section, a charge status section, and a numerical value section as shown below. Before switch on Before turning on the unit for the firs

• Dale Power Solutions E201, Dale Power Solutions Ltd User Manual ………………………………………………………………………………………………………… 15 ECO mode To turn on ECO mode: 1. On the front panel, press for more than 2 s. The following is displayed. 2. Press for more than 0.5 s but less than 2 s. The following is displayed. 3. Press for more than 0.5 s but less than 2 s. OFF stops flashing. 4. Press or to display ON, which flashes. 5. Press for more than 0.

• Dale Power Solutions E201, Dale Power Solutions Ltd User Manual 14 ………………………………………………………………………………………………………… 3. On the front panel, press and hold + (see Figure 4 on page 12) until a beep is heard (after approximately half a second). The LEDs flash initially and then the green inverter LED ( ) should be on. The output voltage and frequency are displayed. If the amber bypass LED ( ) is also on the unit is working in ECO mode (see ECO mode on page 15.

• Dale Power Solutions E201, Dale Power Solutions Ltd User Manual ………………………………………………………………………………………………………… 21 Appendix 1 Signals options RS232 serial port Units are fitted with a standard RS232 serial port, which can be used to: ■ Monitor the UPS power status ■ Monitor the UPS alarm information ■ Monitor the UPS running parameters ■ Perform a battery test To enable RS232 control: 1. Connect the UPS to your computer using the supplied RS232 cable. 2. If present, disconnect the USB cable between UPS and your computer. Note: A USB connection overrides an RS232 connection. 3. Load the supplied software

Related Products and Documents (UPS):

Comparable Devices:

Similar Resources:

• Eaton 9910-E16 (274 pages) Eaton 9130 (9910-E15/E16) UPSInstallation Guide for IBM ApplicationsAsennusopas IBM-sovelluksilleGuide d'Installation pour Applications IBMUSV Installationsanleitung für IBM-AnwendungenGuida all'Installazione per le Applicazioni IBMInstrukcja instalowania dla zastosowań IBMРуководство по установке в системах IBMGuí …

• CyberPower OR1000LCDRM1U (2 pages) OR1000LCDRM1U / OR1500LCDRM1U User’s Manual K01-0000053-01 (SAVE THESE INSTRUCTIONS) This manual contains important instructions that should be followed during installation and maintenance of the UPS and batteries. Please read and follow all instructions carefully during installation and operation of the unit. Read this manual thoroughly before …

• Eaton PowerXpert 9395P-600/600 (232 pages) Eaton PowerXpert 9395 High Performance (9395P-600) UPSInstallation and Operation ManualFor use with 380V, 400V, 415V, and 480V Single UPM (200–300 kVA),Two UPM (400–550 kVA), and Plus 1 (400–600 kVA) UPS ModelsAlso for use with 600V Single UPM (200–275 kVA), Two UPM (300–550 kVA),and Plus 1 (300 kW-550 kW)®® …

• HPE R1500 G5 (3 pages) MF877-00 Page 1 Template Revision A HPE instructions for this template are available at MF877-01 Product End-of-Life Disassembly Instructions Product Category: Servers Marketing Name / Model [List multiple models if applicable.] HPE R1 …

• Ablerex 625L (2 pages) This manual contains important safety instructions. Please follow all instructions carefully during installation. Read this manual thoroughly before attempting to unpack, install or operate. CAUTION ˙ To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area, free of conductive contaminants. ˙ Ris …

• Tripp Lite BCPRO600 (5 pages) Tripp Lite1111 West 35th StreetChicago, IL 60609 USATelephone: +(773) 869 1234E-mail: [email protected] #: BCPRO600BC Pro 600VA Tower Standby 120V UPS with USB port Highlights600VA tower 120V standby UPSMaintains AC output during power failures3 UPS battery supported outlets, 3 surge-only outletsUSB port, TEL/DSL/ethernet protection, 97% efficien …

Comments, Questions and Opinions: