Blade 180 QX HD Instruction Manual
|
Blade 180 QX HD, 2 EN WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury. This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way
Blade 180 QX HD, 3 EN First Flight Preparation .....................................................4 Flying Checklist ...............................................................4 Charging Warnings...........................................................4 Installing the Landing Gear ..............................................5 Installing the Transmitter Batteries (RTF) ..........................5 Installing the Flight Battery ..............................................5 Transmitter and Receiver Binding .....................................6 SAFE Technology .............................................................7
Blade 180 QX HD, 4 EN The Battery Charger (EFLC1010) included with your quadcopter has been designed to safely charge the Li-Po battery. CAUTION: All instructions and warnings must be followed exactly. Mishandling of Li-Po batteries can result in a fi re, personal injury and/or property damage. • By handling, charging or using the included Li-Po battery, you assume all risks associated with lithium batteries. • If at any time the battery begins to balloon or swell, discontinue use immediately. If charging or discharging, discontinue and disconnect. Continuing to use, charge or discharge a battery that is balloonin
5 EN Installing the Transmitter Batteries (RTF) Replace the transmitter batteries when the power LED fl ashes and the transmitter beeps. 1. Lower the throttle and throttle trim to the lowest settings. 2. Power on the transmitter. 3. Install the battery by sliding it into the battery mounting slot below the 5-in-1 control unit. Slide the battery into the slots with the label facing upward so
6 EN To bind or re-bind your quadcopter to your chosen transmitter, please follow the directions below. General Binding Procedure 1. Disconnect the fl ight battery from the quadcopter. 2. Select a clean model memory on your transmitter (computer radios only). 3. Select Acro or Airplane model type on your transmitter. 4. Make sure all servo reversing is set to Normal on your transmitter. 5. Cente
Blade 180 QX HD, 7 EN RTF Transmitter Control F G H E A D C B Camera trigger (bind switch) Flight mode switch H ABCDEFGH Mode 1 Power LED/ fl ight mode indicator Aileron (Left/Right) Throttle (Up/Down) Throttle Trim Aileron Trim ON/OFF Switch Rudder Trim Eleva- tor Trim Rudder (Left/Right) Elevator (Up/Down) Mode 2 Power LED/ fl ight mode indicator Aileron (Left/Right) Elevator (Up/ Down) Eleva- tor Trim Aileron Trim ON/OFF Switch Rudder Trim Throttle Trim Rudder (Left/Right) Throttle (Up/Down) When pressed down, trim buttons make a sound that increases or decreases in pitch at each pressing. The middle or neutral
Blade 180 QX HD, 8 EN RTF Change fl ight modes by moving the three-position fl ight mode switch. Ensure the fl ight mode switch is in the desired position before fl ying. • In stability low angle mode (switch position 0), the controls provide a minimum bank angle. This mode is shown by the fl ight control board on the quadcopter glowing solid blue. • In stability high angle mode (switch position 1), the controls provide for a maximum bank angle. This mode is shown by the fl ight control board on the quadcopter slowly fl ashing blue. • Agility mode (switch position 2) is shown by the fl ight control board on the quadcopter glo
Blade 180 QX HD, 9 EN Transmitter Setup Table Transmitter Model Type Reverse Setup Mode Setup Switch Positions Camera Operation Dual Rate Switch High Rate Low Rate MLP4DSM N/A N/A N/A Default = Stability Mode, Low Angle (Quad Solid Blue LED) Still Mode(Default) Press Left Stick = Take Picture Video Mode Press Left Stick = Start/Stop Recording Press & Hold Left Stick (4 Seconds) = Change Modes Rate 100% Fixed N/A Press Right Stick = Agility Mode (Quad Solid Red LED) MLP6DSM N/A N/A N/A Channel 5 (0) = Stability Mode, Low Angle Still Mode(Default) Press Trainer = Take Pict
Blade 180 QX HD, 10 EN Transmitter Model Type Reverse Setup Mode Setup Switch Positions Camera Operation Dual Rate Switch High Rate Low Rate DX4e (New) w/ 3 Position Switch N/A N/A N/A Channel 5 (0) = Stability Mode, Low Angle Still Mode(Default) Press Trainer = Take Picture Video Mode Press Trainer = Start/Stop Recording Press & Hold Trainer for 4 Seconds = Change Modes Rate 100% Fixed 70% Fixed Channel 5 (1) = Stability Mode, High Angle Channel 5 (2) = Agility Mode DX5e (New) w/ 3 Position Switch N/A N/A N/A Channel 5 (0) = Stability Mode, Low An
Blade 180 QX HD, 11 EN Transmitter Model Type Reverse Setup Mode Setup Switch Positions Camera Operation Dual Rate Switch High Rate Low Rate DX7S Acro AUX1 - R All Others - N Switch Select: Trainer to Aux 1; F Mode to Gear Set All Others to Inh MIX 1: GER > GER RATE: 0% -100% OFFSET: 0%; TRIM: Inh SW: Mix0 F MODE (0) = Stability Mode, Low Angle Still Mode(Default) Press Trainer = Take Picture Video Mode Press Trainer = Start/Stop Recording Press & Hold Trainer for 4 Seconds = Change Modes ELEV-AIL D/R 100% 70% F MODE (1) = Stability Mode, High Angle F MODE (1); HOLD (1) = Agility Mod
Blade 180 QX HD, 12 EN LED Codes Equipment LED Color LED Status Operation Quadcopter Blue Rapid Blink Bind Mode Solid Stability Mode low angle Slow Blink Stability Mode high angle Red Solid Agility Mode Red and Blue Solid Low Battery Blink Loss of RF/TX Off RTF Transmitter Red Blink Low Rate Solid Hi Rate Elevator ForwardElevator down Elevator up Backward Left Side View Left Side View Rudder Rudder left Rudder right Nose Yaws Right Nose Yaws Left Understanding the Primary Flight Controls If you are not familiar with the controls of your 180 QX HD, take a few minutes to familiarize yourself with them before attempting your fi rst fl ight. Throttle Throttle down Th
Blade 180 QX HD, 13 EN Takeo Increase the throttle until the model is approximately 2 ft. (600mm) off the ground and check the trim so the model fl ies as desired. Once the trim is adjusted, begin fl ying the model. Typical fl ight times for the included battery range from 5 to 10 minutes. Low Voltage Cuto (LVC) LVC decreases the power to the motors when the battery voltage gets low. When the motor power decreases and the blue and red LEDs on the 5-in-1 unit are solid, land the aircraft immediately and recharge the fl ight battery. LVC does not prevent the battery from ove
14 EN Installation 1. Install the included hook and loop tape on the bottom of the camera, as shown. 2. Install the camera on the model using the included hook and loop strap. 3. Connect the servo lead from the main board to the camera servo lead port. 4. Press the camera power button. The red LED will glow solid during initialization, then turn off. The blu
Blade 180 QX HD, 15 EN Troubleshooting Guide Problem Possible Cause Solution Quadcopter control response is inconsistent or requires extra trim to neutralize move- ment. Aircraft not initialized on a level sur- face. Disconnect the fl ight battery, center the control trim and re-initialize the quadcopter. Battery not correctly placed in battery slot. Adjust battery position so quadcopter bal- ances in the center of the frame. Quadcopter will not respond to throttle. Throttle too high and/or throttle trim is too
Blade 180 QX HD, 16 EN 3 16 4 7 14 13 2 2 1 10 6 15 8 9 8 9 5 11 12 Exploded View Parts Listings Part # Description 1 BLH3506 Main Gear: BMSR/X, mCP X, mQX 2 BLH3515, EFLH2215 Outer Shaft Bearing 3 x 6 x 2mm(2): BMCX/2/MSR/X, FHX, MH-35, MCP X, mQX 3 BLH7401 5-in-1 Control Unit, RX/ESCs/Mixer/ Gyros/Camera Control: 180 QX HD 4 BLH7402 Canopy: 180 QX HD 5 BLH7403 5-in-1 Mounting Frame: 180 QX HD 6 BLH7404 Landing Gear 180 QX HD 7 BLH7502 Thruster Boom with Wiring (2): mQX 8 BLH7503 Motor with Pinion, Clockwise Rotation: mQX 9 BLH7504 Motor with Pinion, C
Blade 180 QX HD, 17 EN Limited Warranty What this Warranty Covers Horizon Hobby, Inc., (Horizon) warrants to the original purchaser that the product purchased (the "Product") will be free from defects in materials and workmanship at the date of purchase. What is Not Covered This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use, installation, operation or maintenance, (iii) modification of or to any part of the Product
Blade 180 QX HD, 18 EN Warranty and Service Contact Information FCC Information This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
19 EN Declaration of Conformity (in accordance with ISO/IEC 17050-1) No. HH2013091401 Product(s): 180 QX HD BNF Item Number(s): BLH7480 Equipment class: 1 The object of declaration described above is in conformity with the requirements of the specifi cations listed below, following the provisions of the European R&TTE directive 1999/5/EC, EMC Directive 2004/108/EC and LVD Directive 200
JXD Pioneer UFO 509V Quadcopters Instruction manual
Pioneer UFO 509V |
Blade 350 QX3 Quadcopters Instruction manual
350 QX3 |
Blade nano QX Quadcopters Manual
nano QX |
Blade BLH02000 Quadcopters Instruction manual
BLH02000 |
Tornado H920 Quadcopters Operation & user’s manual
H920 |
Foxtech KRAKEN 130 V2 Quadcopters Assembly manual
KRAKEN 130 V2 |
Blade CHROMA Quadcopters Quick start manual
CHROMA |
Blade 350 QX3 Quadcopters Instruction manual
350 QX3 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Lippert Components | Standalone Smart Jack | Install manual | lippert-components/standalone-smart-jack-65W.pdf | 09 Feb 2024 | 6 | |
2 | Walker | WP16LEDVD Saorview | Operating instructions manual | walker/wp16ledvd-saorview-WXP.pdf | 09 Mar 2024 | 43 | |
3 | MALUX | INDUTEL IP | Operating manual | malux/indutel-ip-L13.pdf | 09 Mar 2023 | 24 | |
4 | Metz | 081 | Operating instructions manual | metz/081-Y7R.pdf | 16 Oct 2022 | 27 | |
5 | KMC Controls | MEP-1500 Series | Installation manual | kmc-controls/mep-1500-series-A33.pdf | 07 Jul 2023 | 2 | |
6 | Pacific energy | z35 | Installation manual | pacific-energy/z35-FM6.pdf | 29 May 2023 | 56 |
Xaircraft
XAircraft X650 Value安装说明书INSTRUCTION MANUAL在使用XAircraft X650 Value之前,请仔细阅读此说明书。Read the manual carefully before using XAircraft X650 Value.2011-07 V1.1Model: X650 V-4
…
X650 Value(21 pages) |
ACME
www.acme-online.de ACME the game company ManualManualManualManual Please read carefully before first use! Manual Technical Data Size: 50x50x25mm Weight: approx. 8g Recommended Age: 10+ years Field of use: Indoor Battery: 3.7V LiPo; 100mAh Contro …
Zoopa Q Zepto 55(10 pages) |
Lynx
LX2136- ZAP 150 ZEROLYNX MANUAL DOC .REV .A 07-12-2016INSTRUCTION MANUALSPECIFICATIONSFrame Weight: 50gMaterials: Pure Carbon FiberSize: 150mmMaximum Propeller:3 inchMotor mount: 13xx motor, Xnova RM1806-2300KV, Xnova 2205-2300KV hypersonic racing FPV motor. Flight controller mount: 30.5mm x 30.5mm and 20x20mmFPV Camera mount: can be adjusted from 0 to 45
…
ZAP 150 ZERO(5 pages) |
Arris
User Manual for ARRIS FPV250 with SPRacing F3 Flight Controller(Cleanflight 1.12.00)1. How to Connect the F3 Flight Controller to the Computer.1.1. Do not connect the F3 flight controller to the computer at the first step.1.2. You will need to install the Google Chrome browser to install Cleanflight Software.1.3. Open the Goggle Chrome browser, search and in …
FPV250(17 pages) |
TYPHOON
NOTICES AND WARNINGSOVERVIEWTYPHOON Q500+ Quickstart V3.0IMPORTANT NOTE: All safety precauons and warnings, instrucons, warranes and other collateral informaon is subject to change at the sole discreon of Yuneec. For the most up-to-date informaon please visit the corresponding product page at www.Yuneec.com or contact the nearest Yune …
Q500(2 pages) |
dji
Dualv1.0MAVIC 2 ENTERPRISEQuick Start Guide ᔘ䕌ڒ䬕ᠴࢄᔘ䕌ڒ䪭ᠴࢄクイックスタートガイド퀵 스타트 가이드 Kurzanleitung Guía de inicio rápido Guide de démarrage rapide Guida di avvio rapido SnelstartgidsGuia de início rápidoGuia de Início RápidoКраткое руководство пользователя
…
Mavic 2 Enterprise(44 pages) |
Malmbergs Transmitter RNP-01Instruction manual for Malmbergs RNP-01 Transmitter RNP-01, 2 |
PCTV Systems TV Receiver Broadway Triple HD 292Broadway Triple HD 292 Quick install manual - 3C5O6C Broadway Triple HD 292, 2 |
Warmup Thermostat OTN-1991-WAThermostat #BF76PM OTN-1991-WA, 8 |
EPOX Motherboard kl-133mEPOX kl-133m User Manual (Operation & user’s manual), @J41W31 kl-133m, 72 |
Aurora Paper Shredder AS1023CDPaper Shredder Manual (Aurora AS1023CD) AS1023CD, 3 |
DAEWOO ELECTRONICS TV DTQ-20J5FC#2SU6GH DTQ-20J5FC: DAEWOO ELECTRONICS TV Owner Documentation DTQ-20J5FC, 36 |
Mitsubishi Electric Air Conditioner MXZ-8B140PDF User Guide (@BQK6ZE), Mitsubishi Electric MXZ-8B140 Air Conditioner (16/01/2024) MXZ-8B140, 16 |
Sierra Measuring Instruments Smart-Trak 100 seriesSierra Smart-Trak 100 series User Manual (Doc Type: Measuring Instruments Instruction manual) Smart-Trak 100 series, 88 |
Philips Speakers DS8530#P2QFUC DS8530: Philips Speakers Owner Documentation DS8530, 2 |
Acer LCD TV AL2671WOperation & user’s manual for Acer AL2671W LCD TV AL2671W, 25 |
Edimax Network Router CV-7438nDM#AI571I: CV-7438nDM Network Router Hardware CV-7438nDM, 4 |
Konica Minolta Network Card bizhub 181Konica Minolta bizhub 181 Network Card Operation & user’s manual bizhub 181, 322 |