Boomerang Sprint Instruction Manual
|
Boomerang Sprint, Wingspan........ 75.5" (1920mm) Length............. 73" (1850 mm) Weight 14lb.( 6.35kg ) Dry. Radio....... 5 to 7 Channels. Designer Alan Cardash Boomerang RC Jets, LLC. Website www.boomerang-RC-jets.com SPRINT Boomerang Aerobatic Sport / Trainer Jet for 12 to 22 Lb. Thrust turbines Almost ready to fly. Speed range from 18 to 150 MPH. SAFETY PRECAUTIONS The SPRINT turbine model is designed for experienced modellers. This model is not recommended for beginners to R/C flying and should not be attempted by those with insuf- ficient building and flying experience. This manual is
Boomerang Sprint, 3 1 2 3 Centre Wing 2.6 x12mm Screws 1 2 x 200mm Pushrod 1 Clevis 4 Self-adhesive Self-adhesive Self-adhesive Open the holes for access to the wing fixing bolts then apply the self adhesive rings. Warning! Cut away covering film. Not supplied Be sure to glue securely. This is Vital for safe flying! Apply thin Cyano glue to both sides of hinges to ensure good penetration. Typical Servo Mount Flap Servo Installation 14 29 30 Check Hatch fit Canopy fix 1 Aluminum tube Aluminum tube Drill to suit your servos
Boomerang Sprint, 4 4 To Make the Pushrods to the length required;- (1) Make a 90 degree bend in the wire at the length required to meet the output hole in the servo arm with the servo centred. (2) Now make a second bend off at 90 degrees to the first one, left or right, in the wire at approx. 3mm away from the first bend. (3) Straighten the wire by gripping each side of the “Z” bend with pliers and slowly turning until the ends are in line. Now cut off the excess wire. The output hole in the servo
Boomerang Sprint, 5 7 8 6 Main Landing Gear Main Landing Gear 2 2 5.2mm Collar 3 x 4mm grub Screw 12 26 24 25 6 2 x 8mm TP Screw Noseleg Noseleg Cover Plate 2.6 x12mm TP Screw 16 2.6 x12mm TP Screw 2.6 x12mm TP Screw Requires some modification on main gear cover. For Retractable landing gear . Not Supplied. Not Supplied. Not Supplied. Main Landing Gear Cut off shaded portion. The main leg retracts should be fitted about ½” inboard of the centre wing tip. 2 x 8mm TP Screw Trim the cover plate as required. Fuselage/Wing joining 4mm 4mm Washer 4 x 50mm Bolt NO:1007 2x8mm Screw 2 2 4 x 50mm Bolt 4mm Washer 2 NO:1007 2x8mm Screw 6 Cut away the covering from the slots on top of the centre wing. Place
Boomerang Sprint, 6 10 11 9 Aileron Servo installation Outer wing panel Centre Wing When cutting away the film,for the servo mount leave a gener- ous overhang to allow for the strong shrinkage of the Profilm (Orocover) when you finally iron it back in place. A B Assemble left and right sides the same way. Assemble left and right sides the same way. Be sure to apply instant type CA glue to both sides of each hinges. (low viscosity type) Cut away covering film. Warning! 2.6 x12mm TP Screw Be sure to glue securely. This is Vital for safe flying! 11 23 22 For Retractable landing gear. Noseleg Servo Noseleg Mounting “Trim the Cover Plate to clear the leg.” 8 2.6 x12mm TP Screw 2
7 14 Rudder Servo installation Cut away covering film. 8 2.6 x12mm TP Screw 2.6 x12mm TP Screw Assemble left and right sides the same way. 500mm. servo extension wires to rudder servos in both booms. Alos 700mm. extension wires to Elevator Servo in Left hand boom only .(not supplied) 10 21 20 In order to save weight at the tail end, you can use “Midi” s
8 16 17 15 Rudder installation Assemble left and right sides the same way Assemble left and right sides the same way. Rudder installation 9 19 18 Elevator Servo installation Assemble left and right sides the same way. Right sides Final Assembly The tailskids are designed to swivel freely. 2 2 x 200mm Pushrod 2 Clevis 2 2 4 2 3 x 50mm Bolt 3mm Nut 3mm Washer 3mm Horn 3mm 3mm
Boomerang Sprint, 8 16 17 15 Rudder installation Assemble left and right sides the same way Assemble left and right sides the same way. Rudder installation 9 19 18 Elevator Servo installation Assemble left and right sides the same way. Right sides Final Assembly The tailskids are designed to swivel freely. 2 2 x 200mm Pushrod 2 Clevis 2 2 4 2 3 x 50mm Bolt 3mm Nut 3mm Washer 3mm Horn 3mm 3mm Nut 3mm Washer 3mm Horn 3 x 50mm Bolt 3mm 14mm 54mm Completed Apply thin Cyano to the 3 x 50mm. Bolt after pushing it through the control surface, and immediately tighten the nut to prevent rotation. 3mm. or
7 14 Rudder Servo installation Cut away covering film. 8 2.6 x12mm TP Screw 2.6 x12mm TP Screw Assemble left and right sides the same way. 500mm. servo extension wires to rudder servos in both booms. Alos 700mm. extension wires to Elevator Servo in Left hand boom only .(not supplied) 10 21 20 In order to save weight at the tail end, you can use “Midi” servos for the
Boomerang Sprint, 6 10 11 9 Aileron Servo installation Outer wing panel Centre Wing When cutting away the film,for the servo mount leave a gener- ous overhang to allow for the strong shrinkage of the Profilm (Orocover) when you finally iron it back in place. A B Assemble left and right sides the same way. Assemble left and right sides the same way. Be sure to apply instant type CA glue to both sides of each hinges. (low viscosity type) Cut away covering film. Warning! 2.6 x12mm TP Screw Be sure to glue securely. This is Vital for safe flying! 11 23 22 For Retractable landing gear. Noseleg Servo Noseleg Mounting “Trim the Cover Plate
Boomerang Sprint, 5 7 8 6 Main Landing Gear Main Landing Gear 2 2 5.2mm Collar 3 x 4mm grub Screw 12 26 24 25 6 2 x 8mm TP Screw Noseleg Noseleg Cover Plate 2.6 x12mm TP Screw 16 2.6 x12mm TP Screw 2.6 x12mm TP Screw Requires some modification on main gear cover. For Retractable landing gear . Not Supplied. Not Supplied. Not Supplied. Main Landing Gear Cut off shaded portion. The main leg retracts should be fitted about ½” inboard of the centre wing tip. 2 x 8mm TP Screw Trim the cover plate as required. Fuselage/Wing joining 4mm 4mm Washer 4 x 50mm
Boomerang Sprint, 4 4 To Make the Pushrods to the length required;- (1) Make a 90 degree bend in the wire at the length required to meet the output hole in the servo arm with the servo centred. (2) Now make a second bend off at 90 degrees to the first one, left or right, in the wire at approx. 3mm away from the first bend. (3) Straighten the wire by gripping each side of the “Z” bend with pliers and slowly turning until the ends are in line. Now cut off the excess wire. The output hole in the servo arm may have to be drilled out to accommodate the “Z” bend wire passing through it. Adjustment of the p
Boomerang Sprint, 3 1 2 3 Centre Wing 2.6 x12mm Screws 1 2 x 200mm Pushrod 1 Clevis 4 Self-adhesive Self-adhesive Self-adhesive Open the holes for access to the wing fixing bolts then apply the self adhesive rings. Warning! Cut away covering film. Not supplied Be sure to glue securely. This is Vital for safe flying! Apply thin Cyano glue to both sides of hinges to ensure good penetration. Typical Servo Mount Flap Servo Installation 14 29 30 Check Hatch fit Canopy fix 1 Aluminum tube Aluminum tube Drill to suit your servos. Not supplied Not supplied 2.6 x12mm TP Screw Cut away covering film. For Main Landing Gear 3mm 3mm 3mm Nut 3mm Washer 4 2.6 x12mm TP Screw 1 1 2 1 3 x 50mm Bo
Boomerang Sprint, Wingspan........ 75.5" (1920mm) Length............. 73" (1850 mm) Weight 14lb.( 6.35kg ) Dry . Radio....... 5 to 7 Channels. Designer Alan Cardash E-Mail;[email protected] Website www.boomerangjets.com TRIMMING SET UP & FLYING NOTES Boomerang SPRINT is not tricky or difficult to set up. Set the Centre of Gravity no less than 10” (255 mm.) forward of the Trailing Edge for the first flights. Start with 5/8” up and ½” down Aileron (16 & 13 mm.). Elevators 5/8” (16mm) up and down. Adjust later to your personal preferences. The flap is very effective in slowing the glide speed. Set it
Boomerang Sprint,
Black Horse Model Mustang P51 Toy Instruction manual
Mustang P51 |
Approach Engineering AH1 "W" Cobra Toy Assembly instructions manual
AH1 "W" Cobra |
Boomerang XL Toy Assembly manual & user manual
XL |
Air Hogs Vectron Wave Toy Instruction manual
Vectron Wave |
VTech Thomas & Friends Calling All Friends Phone Toy Operation & user’s manual
Thomas & Friends Calling All Friends Phone |
Laser Pegs Mosasaur Toy Assembly instruction manual
Mosasaur |
Air Hogs Saw Blade Toy Instruction manual
Saw Blade |
LEGO Star Wars 10225 Toy Assembly instructions manual
Star Wars 10225 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Sylvania | 6626LDG | Specifications | sylvania/6626ldg-Q75.pdf | 18 Oct 2022 | 2 | |
2 | Acer | Aspire AS5542-5416 | Buyer's manual | acer/aspire-as5542-5416-Q1M.pdf | 11 Feb 2023 | 3 | 0.19 Mb |
3 | FUNAI | DCVR-4800 | Service manual | funai/dcvr-4800-WL8.pdf | 21 Jun 2023 | 97 | 11.23 Mb |
4 | Andis | Promotor PM-3R | Specifications | andis/promotor-pm-3r-4M6.pdf | 12 Dec 2023 | 1 | 0.33 Mb |
5 | Yamaha | STAGEPAS 500 | Important safety instructions | yamaha/stagepas-500-N68.pdf | 16 Mar 2024 | 2 | 0.89 Mb |
6 | Goldmund | TELOS 350 | Operation & user’s manual | goldmund/telos-350-4D2.pdf | 02 Jun 2023 | 15 | 0.1 Mb |
FEBER
· IT00202250U.S.AÑOSYEARSANSANOSJAHREJAARANNIWIEKЛЕТ· EDAD RECOMENDADA:· RECOMMENDED AGE:· ÂGE RECOMMANDÉ:· IDADE RECOMENDADA:· EMPFOHLENES ALTER:· AAN TE BEVELEN LEEFTIJD:· ETÀ RACCOMANDATA:· ZALECANY WIEK:· РЕКОМЕНДОВАННЫЙ ВОЗРАСТ:3+· PESO MÁXIMO RECOMENDADO:· RECOMMENDED MAXIMUM WEIGHT:· POIDS MAX. RECOMMANDÉ:· …
My friendly Dino 12V(14 pages) |
Associated Electrics
ASSOCIATED 1:10 SCALE ELECTRIC BUGGY MANUALINSTRUCTION MANUAL FOR THE RC10B3 BUGGY KITS#9003, 9013, 9032 & 9043Masami Hirosaka’s RC10B3 won the‘99 IFMAR World Championships!©2000 Associated Electrics, Inc.ASSOCIATED’S RC10B3--6 TIMES IFMAR WORLD CHAMPION!RC10B3 TQ’d & wonthe 1999 IFMAR Worlds!RC10B3 TQ’d & wonthe 1999 IFMAR Worlds!ASSO …
RC10B3(8 pages) |
GRAUPNER
GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Änderungen vorbehalten! Keine Haftung für Druckfehler 11/2008 1 zu Best.-Nr. 9594 ANLEITUNG Heinkel He 111 Für Elektroantrieb mit 3 LiPo-Zellen oder zwei OS MAX 25 FX Es wird eine Fernsteuerung mit 6 Funktionen benötigt
…
Heinkel He 111(81 pages) |
Enabling Devices
For Technical Support: Call our Technical Service Department Monday through Friday, 9 a.m. to 5 p.m. (EST) 1-800-832-8697 [email protected] Narwhal Bubble Blower & Rainbow Switch Bundle #2336 USER’S GUIDE 50 Broadway Hawthorne, NY 10532 Tel. 914.747.3070 / Fax 914.747.3480 T …
2336(2 pages) |
BearCreeks
BearCreeks Navimate User Guide 5.8GHz BearCreeks GmbH Marie-Curie-Str. 6, 85055 Ingolstadt, Germany Tel: +49 841 Fax: www.bearcreeks.com Email: [email protected]
…
Navimate(18 pages) |
Flyzone
FLZA2100SPECIFICATIONSWingspan:8.46 in [ 215 mm]Total Length:9 in [ 230 mm]Weight:0.3 oz [8.5 g]IMPORTANTREAD THROUGH THIS MANUAL BEFORE STARTING CONSTRUCTION. IT CONTAINS IMPORTANTINSTRUCTIONS AND WARNINGS CONCERNING THE ASSEMBLY AND USE OF THIS MODEL.READ THROUGH THIS MANUAL BEFORE STARTING CONSTRUCTION. IT CONTAINS IMPORTANTINSTRUCTIONS AND WARNINGS CONCE …
Inum(8 pages) |
Zoom Computer Hardware 9030Zoom Computer Hardware Operation manual (File: zoom-9030-operation-manual-69, 02.01.2024) 9030, 69 |
AccuScreens Projection Screen ELECTRIC SCREENProjection Screen #352OS6 ELECTRIC SCREEN, 8 |
Shark Vacuum Cleaner SV729Vacuum Cleaner #B48RJI SV729, 12 |
Zimmer Medical Equipment Soleo StimZimmer Soleo Stim User Manual (Doc Type: Medical Equipment Operation & user’s manual) Soleo Stim, 104 |
Philips CRT TV 21PT5435#C3YP54 21PT5435: Philips CRT TV Owner Documentation 21PT5435, 3 |
Billion Modem BIPAC 7000BIPAC 7000 Operation & user’s manual - WI2F17 BIPAC 7000, 31 |
Whirlpool Dishwasher WDF550SAAB0Dishwasher #L22F2U WDF550SAAB0, 16 |
HP Flat Panel TV LT4700HP LT4700 Flat Panel TV Operation & user’s manual LT4700, 200 |
macaroon Wireless Router M1macaroon M1 User Guide (Manual ), @SVYB77 M1, 13 |
Roger Extender MCX402DR-BRDExtender PDF Operating manual MCX402DR-BRD, 11 |
Packet Power Gateway Ethernet Gateway Version 3User Guide: Packet Power Ethernet Gateway Version 3 (223L74, Upd.Sun 01.2024) Ethernet Gateway Version 3, 11 |
Dors Cash Register 220Dors 220 Guide (Operation & user’s manual), @895B5T 220, 14 |