Borri B400-010-B (C) Operation & User’s Manual
|
Borri B400-010-B (C), -27- Please have the following information available before calling the After-Sales Service Department: 1. Model number, serial number 2. Date on which the problem occurred 3. LCD/LED display status, Buzzer alarm status 4. Utility power condition, load type and capacity, environment temperature, ventilation condition 5. The information (battery capacity, quantity) of external battery pack if the UPS is “C” model 6. Other information for complete description of the problem www.upsdirect.com
Borri B400-010-B (C), -19- 6.2 Battery mode The LCD display for the UPS operating in battery mode is shown in the following diagram. The information about the mains power, the battery, the UPS output and the load is displayed. The “Battery” and “3” code indicate the UPS is working in the battery mode. (1) When the UPS is running in battery mode, the audible alarm beeps once every 4 seconds. If the “ON” button on the front panel is pressed for more than 1 second, the alarm will stop beeping (in silence mode). Press the “ON” button once again for more than 1 second to resume the alarm function. 2) If the UPS is running in
Borri B400-010-B (C), -12- 5. Connection and Operation 5.1 Inspection: Inspect the packaging carton and its contents for damage. Please inform the transport agency immediately should you find signs of damage. Please keep the packaging in a safe place for future use. 5.2 Connection: (1) UPS Input Connection If the UPS is connected via the supplied input power cable, please connect to a socket which has necessary protection and capacity: over 6A for B400-010-B and B400-010-C, over 7A for B400-020-B, 13A for B400-020-C, B400-030-B, and B400-
Borri B400-010-B (C), -25- Emergency supply period shorter than nominal value Batteries not fully charged / batteries defect Charge the batteries for at least 5 - 8 hours and then check capacity. If the problem still persists, consult your dealer. Fan fail Fan abnormal Check if the fan is running Battery over voltage Battery is over charged The UPS will switc to battery mode automatically, and after the battery voltage is normal and the mains is normal, the UPS would switching to Online mode automatically again. Battery low Battery voltage is low When the audible alarm is sounding every second, the battery is almost empty. Charge fail The charger is broken Not
Borri B400-010-B (C), -14- Normally close Normally the EPO connector is closed with a wire on the rear panel. Once the connector is open, the UPS would stop the output until the EPO status is disabled Enable the EPO status Disable the EPO status 5.3 Battery charge: The UPS system should be plugged in to the mains and switched on for 2 hours to ensure the batteries are fully charged. The UPS can be used before this time however the specified full backup time may not be achieved. 5.4 Turn on the UPS: (1) With mains power connected: Press and hold the “I” button to turn on the UPS, the UPS will go
Borri B400-010-B (C), -24- Overload 29 Fault Code Bus fault 05 Inverter fault 06 Overload fault 07 Over temperature fault 08 Inverter short 14 Bus short 28 If the UPS system does not operate correctly, please attempt to solve the problem using the table below. Problem Possible cause Remedy No indication, no warning tone even though system is connected to mains power supply No input voltage Check building wiring socket outlet and input cable. BYPASS LED lights up even though the power supply is available Inverter is not switched on Press On-Switch “I”. BATTERY LED lights up, and audible alarm sounding every 1 beep in every 4 secon
Borri B400-010-B (C), -33- 11. Software Free Software Download – WinPower WinPower is a new UPS monitoring software, which provides user-friendly interface to monitor and control your UPS. This unique software provides safely auto shutdown for multi-computer systems while power failure. With this software, users can monitor and control any UPS on the same LAN regardless of distance from the UPSs. Installation procedure: 1. Go to the website: http://www.borri.co.uk/softwaredownload
Borri B400-010-B (C), CONTENT 1. Safety and EMC Instructions ..............................................................1 1.1 Installation......................................................................................... 1 1.2 Operation .......................................................................................... 2 1.3 Maintenance, servicing and faults ....................................................3 1.4 Transport........................................................................................... 3 1.5 Storage ...................
Borri B400-010-B (C), -4- 1.6 Standards * Safety IEC/EN 62040-1-1 * EMI Conducted Emission..........................:IEC/EN 62040-2 Category C1 Radiated Emission.............................:IEC/EN 62040-2 Category C1 Harmonic Current...............................:IEC/EN 61000-3-2 Voltage Fluctuation and Flicker..........:IEC/EN 61000-3-3 *EMS ESD...................................................:IEC/EN 61000-4-2 Level 4 RS.....................................................:IEC/EN 61000-4-3 Level 3 EFT....................................................:IEC/EN 61000-4-4 Level 4 SURGE.............
-21- 6.4 NO output mode The LCD of the UPS display in “No output mode” is shown in the following diagram. The information about the mains power, the battery, the UPS output and the load is displayed. The “0” code indicates the UPS is working in the “No output” mode. 6.5 EPO (Emergency Power Off) It is also called RPO (Remo
-13- (2) UPS Output Connection The output of the UPS is IEC socket-type 10A for B400-010-B(C) and B400-020-B; 10A for B400-020-C and 10A & 16A for B400-030-B(C); Simply plug the load power cable to the output sockets to complete connection. Model No. Output Socket (pcs) B400-010-B(C) 3 IEC type B400-020-B(C) 6 IEC t
Borri B400-010-B (C), -16- (2) The battery connection procedure is very important. It must be followed exactly to avoid electric shock. (3) Make sure the mains input is off, if there is a battery breaker then turn it off first. (4) Remove the cover of the battery connector on the rear of the UPS, always use the Borri provided battery connection cable. (5) Pay attention to the colour of UPS battery connector: red is the “+” terminal of the battery and black is the “-” terminal of battery, the green one is the earth. Because the connector
Borri B400-010-B (C), -17- 6. Operating Mode for All Models The operating code shown on the LCD screen and explanation are listed in the table below. Under normal circumstances only one code will appear. If warnings are present the appropriate codes will scroll through. Normal operating mode Code No output mode 0 Bypass mode 1 Line mode 2 Battery mode 3 Battery test mode 4 ECO mode 5 Converter mode 6 www.upsdirect.com
Borri B400-010-B (C), -28- 8. Maintenance 8.1 Operation The UPS system contains no user-serviceable parts. If the battery service life (3~5 years at 25°C ambient temperature) has been exceeded, the batteries must be replaced. In this case please contact Borri. 8.2 Storage If the batteries are stored in a temperate controlled area, they should be charged every three months for 1~2 hours. You should shorten the charging intervals to two months at locations subject to high temperatures. 8.3 Battery Replacement If the battery
Borri B400-010-B (C), -32- 10.3 AS400 Interface (Option) Except for the communication protocol as mentioned above, this series of UPS has AS400 card (an optional accessory) for AS400 communication protocol. Please contact your local distributor for details. The following is the pin assignment and description of DB-9 connector in AS400 card. Pin # Description I/O Pin # Description I/O 1 UPS Fail Output 6 Bypass Output 2 Summary Alarm Output 7 Battery Low Output 3 GND Input 8 UPS ON Output 4 Remot
Borri B400-010-B (C), -7- 4. Panel Description The Display Panel Switch Function ON-Button Pressing this button turns on the UPS system. Pressing this button while the UPS is in battery mode will deactivate the acoustic alarm. Pressing this button while the UPS is in Line mode, ECO Mode or Converter mode will cause the UPS to perform a battery test. OFF-Button Pressing this button when mains power is normal, the UPS will switch to Bypass mode, the inverter is also switched off. If Bypass is enabled, then the outpu
6.7 Converter mode..............................................................................22 6.8 Abnormal mode...............................................................................22 7. Trouble Shooting................................................................................23 8. Maintenance......................................................
-10- Indicates the battery is over-charge, and the UPS would be transfer to Battery mode Indicates low battery and imminent shutdown of the UPS. Indicates the battery is charging Indicates the battery is discharging UPS status Information Indicates UPS operating status including the operating mode, or warnings or faults on the UPS, the codes are
Borri B400-010-B (C), -30- 9.3 Typical backup time (Typical values at 25°C in minutes :) Model No. 100 % Load 50 % Load B400-010-B 5 14 B400-020-B 9 21 B400-030-B 5 15 9.4 Dimensions and weights Model No. Dimensions W×D×H (mm) Net Weight (kg) B400-010-B 145×400×220 13 B400-010-C 145×400×220 7 B400-020-B 192×460×347 31 B400-020-C 192×460×347 13 B400-030-B 192×460×347 31 B400-030-C 192×460×347 13 www.upsdirect.com
Borri B400-010-B (C), -20- 6.3 Bypass mode The LCD display for the UPS operating in bypass mode is shown in the following diagram. The information about the mains power, the battery, the UPS output and the load is displayed. The UPS will beep once every 2 minutes while in bypass mode. The “Bypass” and “1” code indicate the UPS is working in the bypass mode. The UPS will not support the load while in bypass mode. The power used by the load is supplied from the mains power via internal filter and is unprotected. Bypass mode www.upsdirect.com
Salicru NX Series UPS User's manual, installation and start-up
NX Series |
Borri B8031 UPS Operating manual
B8031 |
Riello WinDialog 40U Plus UPS Operation & user’s manual
WinDialog 40U Plus |
Eaton Powerware 9390 UPS Installation and operation manual
Powerware 9390 |
Borri B9000FXS 60kVA UPS Product manual
B9000FXS 60kVA |
Borri B500EVO-100-B UPS Operation & user’s manual
B500EVO-100-B |
Borri B 200 UPS Operation & user’s manual
B 200 |
Borri B500-R060-C UPS Operation & user’s manual
B500-R060-C |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | MAKELSAN | Challenger Series | Operation & user’s manual | makelsan/challenger-series-HP3.pdf | 22 Dec 2022 | 72 | |
2 | Philips | HTS5590/12 | Quick start manual | philips/hts5590-12-2FC.pdf | 17 Jun 2023 | 18 | 5.35 Mb |
3 | Red Hat | ENTERPRISE LINUX 5.5 - S 2010 | Release note | red-hat/enterprise-linux-5-5-s-2010-BE9.pdf | 14 Oct 2022 | 14 | 0.19 Mb |
4 | Philips | PD7007 | Operation & user’s manual | philips/pd7007-OM2.pdf | 23 May 2023 | 27 | 1.62 Mb |
5 | Whirlpool | GJC3654RB02 | Parts list | whirlpool/gjc3654rb02-2DW.pdf | 07 Mar 2024 | 3 | 0.24 Mb |
6 | Dantherm | CDF 10 | Manual | dantherm/cdf-10-568.pdf | 08 Feb 2023 | 16 |
Powercom
U P SUninterruptible Power SystemLine Interactive Network ProtectionPure Sine Wave Output UPSRegular models600A/800A/1000A/1250A1500A/2000A/2500A/3000A&Extended Run-Time Models1000AL/2000AL/3000ALUSER’S MANUALPrinted in USAA
…
600A(20 pages) |
Tripp Lite
SMART3000RM2U Estimated RuntimeLoad in WattsUPS Battery Pack 500W 1,000W 1,100W 1,200W 1,300W 1,400W 1,500W 1,600W 1,700W 1,800W 1,900W 2,000W 2,200W 2,240WAll runtime values are in minutes.SMART3000RM2U Internal Batteries 30 12 11 9.7 8.7 7.8 7.1 6.4 5.9 5.4 5.0 4.6 4.1 4.0SMART3000RM2U 1 BP48V24-2U 105 46 40 36 33 30 27 25SMART3000RM2U 1 BP48V60RT3U 212 96 …
SMART3000RM2U(1 pages) |
Delta
Maintenance Bypass Boxfor Single UPSInstallation & Operation GuideAbout this GuideThis guide contains information about installing and operating the Delta Maintenance Bypass Box for Single UPS (MBB-S). Before you install this unit, please read the safety instructions below.Save these Instructions This guide contains instructions and warnings that should …
MBB-S(2 pages) |
PowerWalker
EN Off Line UPS PowerWalker VFD 400 IEC PowerWalker VFD 600 IEC PowerWalker VFD 800 IEC Quick Start Guide EN/DE/FR/ES/IT/GR/RU/UA/FI/HR/PL/PT/RO/SE
…
VFD 400 IEC(112 pages) |
Ablerex
1 USER’S MANUAL GR1200 This manual contains important safety instructions. Please follow all instructions during installation. Read this manual thoroughly before unpacking, installing or operating. Caution: Risk of Electric Shock • The UPS contains batteries. The output outlets may be electrically live even when the UPS is disconnected from th …
GR1200(2 pages) |
Altronix
Maximal11E- Power Supply 1: 12VDC @ 4A or 24VDC @ 3A.- Power Supply 2: 12VDC @ 4A or 24VDC @ 3A.Maximal33E- Power Supply 1: 12VDC or 24VDC @ 6A.- Power Supply 2: 12VDC or 24VDC @ 6A.Maximal37E- Power Supply 1: 24VDC @ 10A.- Power Supply 2: 12VDC or 24VDC @ 6A.Maximal75E- Power Supply 1: 12VDC @ 10A.- Power Supply 2: 24VDC @ 10A.Maxim …
Maximal series(16 pages) |
Tripp Lite Network Cable N002-005-RD#4JR7F2: N002-005-RD Network Cable Specification sheet N002-005-RD, 3 |
Panasonic Kitchen Appliances MX-SS40Kitchen Appliances Operating instructions manual (Panasonic MX-SS40) MX-SS40, 48 |
Snapper Lawn Mower 2135XPSOperator's manual supplement for Snapper 2135XPS Lawn Mower 2135XPS, 2 |
Beurer Kitchen Appliances MG 280User manual manual for Beurer MG 280 Kitchen Appliances MG 280, 80 |
Uniden Cordless Telephone WDECT3355#L131KR: WDECT3355 Cordless Telephone Owner's manual WDECT3355, 72 |
Ingersoll-Rand Power Screwdriver 41-EU SeriesIngersoll-Rand Product User Manual: 41-EU Series PDF Maintenance information - E24YR6 41-EU Series, 8 |
UNIS Arcade Game Machines JETBALL ALLEYUser Guide: UNIS JETBALL ALLEY (73XQ17, Upd.Thu 02.2024) JETBALL ALLEY, 62 |
Hanna Measuring Instruments HI 96785CInstruction manual for Hanna HI 96785C Measuring Instruments HI 96785C, 8 |
Advantech Desktop ARK-5280Operation & user’s manual for Advantech ARK-5280 Desktop ARK-5280, 88 |
Blue Rhino Outdoor Fireplace WAD808WDBlue Rhino Outdoor Fireplace WAD808WD Owner's manual WAD808WD, 12 |
auna Stereo System 388 DAB+auna Stereo System 388 DAB+ Manual 388 DAB+, 124 |
Vivax Tablet TPC-701 3GVivax Tablet TPC-701 3G Operation & user’s manual TPC-701 3G, 116 |