Manualios.com

Barco R9001300 Owner's Manual

Barco R9001300 Manual Online:

4, 791 votes
Barco R9001300 User Manual
Barco R9001300 User Guide
Barco R9001300 Online Manual

Text of Barco R9001300 User Guide:

  • Barco R9001300, a-1 Appendix A : Standard Source Set Up Files 5975948 RETRODATA 2100 210198 A Standard preprogrammed set up files STANDARD SOURCE SET UP FILES Name : name of file, contains the settings Resolution : image resolution, when followed by ...I means interlaced. FVERT Hz : vertical frequency of the source FHOR kHz : horizontal frequency of the source. FPIX MHz : pixel frequency PTOT : total pixels on one horizontal line PACT : active pixels on one horizontal line LTOT : total lines in one frame LACT : active lines in one frame NAME RESOLUTION FVERT FHOR FPIX PTOT PACT LT

  • Barco R9001300, 8-3 Random Access Adjustment Mode 5975948 RETRODATA 2100 210198 Edit file The Edit file menu makes it possible to change the settings of the file according to the real settings of the connected source. Consult the source specification before entering the data. To start up the EDIT menu, press the control disc forwards or backwards to select EDIT in the FILE menu and press ENTER. Select the file which must be edited (mostly the active file) and press ENTER. The Edit file adaptation menu will be displayed. The following items can be adjusted : Total quantity horizontal pixels Active quantity horizontal pixels Horizontal shift in pixels Horizonta

  • Barco R9001300, 6-2 Sound Control 5975948 RETRODATA 2100 210198   Mono/Stereo Key Please note that this key function is inactive (stereo only.) The Mute Key When the Mute key is pressed, the sound reproduction is stopped. The image is still displayed. To restart the sound reproduction, press the Mute key again. Balance control Adjust the balance with the + and - button until the desired balance is obtained. When TEXT is on; a bar scale and a indicator below the bar scale (between L and R) give a visual indication on the screen of the current balance setting while pressing the + and - buttons. The bar scale increase to the right while pressing the + button (higher sound level on the right box

  • Barco R9001300, 3-1 Power Connections 5975948 RETRODATA 2100 260898 3 POWER CONNECTIONS AC Power cord connection Power cord connection Fuses Projector Status LED Switching On / To Stand-By / Off Lamp Life Fuses Warning For continued protection against fire hazard : - replace with the same type of fuse. - refer replacement to qualified service personnel Fuse type : T16AH/250V Order no. : B370076 AC Power (mains) Cord Connection hard wire remote Internal mains connection permanently connected Internal power switch always to be positioned in the ’1’ ( ON ) state Ensure that the power switch is in the 'on-1' position on the re

  • Barco R9001300, Service Mode 10-7 5975948 RETRODATA 2100 210198 I 2 C Diagnosis Gives an overview of the correct working of the I²C controlled IC's. Highlight I 2 C diagnosis by pressing the control disc forwards or backwards and press ENTER to display the overview. ENTER displays the I 2 C diagnosis menu. EXIT returns to the adjustment selection menu. Select with ê or é then <ENTER> I 2 C DIAGNOSIS DCA INPUT ANALOG TDA8444 42H # # # INPUT ANALOG PCF8574A 74H # # # INPUT ANALOG PCF8574A 78H # # # INPUT ANALOG TDA8444 4EH # # # DECODER 40H # # # LAMP DRIVER PCF8574A 72H # # # AUDIO TEA6310T 80H # # # SERVICE CHANGE LANGUAGE 75 Ω TERMINATION DIMMING I²C DIAGNOSIS MORE ...

  • Barco R9001300, Service Mode 10-2 5975948 RETRODATA 2100 210198 DIMMING 100500 Select with ê or é then <ENTER> <EXIT> to return. SERVICE IDENTIFICATION CHANGE PASSWORD CHANGE PROJ. ADDRESS CHANGE BAUDRATE PC RESET LAMP RUNTIME LAMP RUN TIME HISTORY PRESET INPUT BALANCE MORE ... Select with ê or é then <ENTER> <EXIT> to return. BARCO DATA 2100 Proj. address : 001 Soft. version : 3.0 Config : front/ ceiling Baudrate PC : 9600 text : ON Serial no.: 1010200 Run time : 100 h Select with ê or é then <ENTER> <EXIT> to return. CHANGE PASSWORD Enter new password 0000 Select with ê or é then <ENTER&

  • Barco R9001300, 4-3 Input Connections 5975948 RETRODATA 2100 210198 Permanent hardwire connections allowing operation of front local control panel,internal loud speakers & front input sockets Permanent hardwire connections allowing operation of front local control panel,internal loud speakers & front input sockets 2. Connecting a S-Video source to the 4-mini DIN input (port 3) Separate Y-luma/C-chroma signals for higher quality playback of Super VHS signals.. 1 x 4 pins plug pin configuration : 1 ground luminance 2 ground chrominance 3 luminance 1.0 Vpp ±

  • Barco R9001300, a-2 Appendix A : Standard Source Set Up Files 5975948 RETRODATA 2100 210198 Source Number 90 - 99 These source numbers do not correspond to physical inputs. They can only be used when the projector is equipped with a RCVDS 05 or VS05. An additional adjustment file can be created for these source numbers. This file can contain different settings. The relationship between sources 0 - 9 and 90 - 99 is shown in the diagram below. Follow the steps below to create a second file for sources 0 to 9 : 1. Select the source between 0 and 9. 2. Select the corresponding source number between 90 and 99 with the digit keys on the RCU. 3. Enter the adjustment mode and load a corresponding file. Edit

  • Barco R9001300, 5-1 Controlling 5975948 RETRODATA 2100 210198 310a.DRW 5 fig.1 fig.2 RCU CONTROLLING Battery installation in the RCU. A new battery (not yet installed to save the battery life) is delivered inside the plastic bag with the power cord. Install the battery as follows : Remove the battery cover on the backside of the RCU by pushing the indicated handle a little to the bottom of the RCU. Lift up the top side of the cover at the same time (fig. 1). Insert the new 9 V battery (type 6F22S or equivalent) in the lower compartment and connect the battery to the contact plate. Insert the batte

  • Barco R9001300, 9-1 Installation Mode 5975948 RETRODATA 2100 210198 9 INSTALLATION MODE Starting up the Installation Mode Press the control disc forwards or backwards to highlight Instal- lation and then press ENTER. ENTER continues to the Installation mode selection menu. EXIT returns to operational mode. The following item can be selected in the Installation mode : Configuration : to set up the projector position. Internal Patterns : - outline - color bars - multi-burst - checker board - purity Select with ê or é then <ENTER> &l

  • Barco R9001300, 5-4 Controlling 5975948 RETRODATA 2100 210198 The Pause Key When the Pause key is pressed, the image projection is stopped but the projector remains with full power for immediate restart. The sound is not interrupted. The display on the front of the projector will show a 'P'. To restart the image reproduction : - press pause key, - press exit key or - select a source number. Tint Control Tint is only active for Video and S-Video Inputs. The Tint Control is effective only when using the NTSC 4.43 or NTSC 3.58 system. A bar scale gives a visual indication on the screen of the current tint setting while pressing the + or - butto

  • 8-7 Random Access Adjustment Mode 5975948 RETRODATA 2100 210198 0 2.5 07 Still Video : ON : the displayed image contains less jitter and gives a sharper image. Still Video : OFF : for moving picture. Still Video This function is only used for stationary interlaced images. Highlight Still Video by pressing the control disc forwards or backwards and press ENTER to toggle

  • Barco R9001300, 8-6 Random Access Adjustment Mode 5975948 RETRODATA 2100 210198 Delete To delete a selected file out of the list of files. Use the control disc to select DELETE and press ENTER. The delete selection menu will be displayed. A confirmation menu "Delete file 'file name'?" is displayed. When you want to delete the file, press ENTER. If you do not want to delete the file, press EXIT. Note : the active file cannot be deleted. Push the control disc forwards or backwards to select a file and pre

  • Barco R9001300, 4-4 Input Connections 5975948 RETRODATA 2100 210198 Permanent hardwire connections allowing operation of front local control panel,internal loud speakers & front input sockets Permanent hardwire connections allowing operation of front local control panel,internal loud speakers & front input sockets 4. Connecting a RGB analogue source to port 5 RGB analog input terminals with automatic sync detection. Sync can be separate Horizontal and Vertical sync (RGB-HV), Composite sync (RGB-S) or Sync signals on green (RGsB). Always use an interface when a computer and local monitor have to be connected to the projector. Recommended interfaces to be applied: Universal analog interface. O

  • Barco R9001300, 8-10 Random Access Adjustment Mode 5975948 RETRODATA 2100 210198 Zoom in -128 +1270 Zoom out -128 +1270 Press the control disc to the right or forwards to zoom in (more detail). Press the control disc to the left or backwards to zoom out (less detail). A bar scale with number indicator which can go positive (zoom in) or negative (zoom out). Size Highlight Size by pushing the control disc forwards or backwards and press ENTER to select. The size can be adjusted in a vertical or horizontal way. Pressing the control disc to the r

  • Barco R9001300, 3-2 Power Connections 5975948 RETRO DATA 2100 260898 30 hours before end of lamp lifetime, the following message will scroll over the screen for 1 minute. This message will be repeated every 30 minutes. Press EXIT to remove the message before the minute is over. When the end of lamp lifetime is reached, the following message, with the exact run time is displayed on the screen. Lamp run time is 1000 hours. Operating the lamp longer than 1000 hours may damage the projector. Please replace the lamp. When OK (ENTER) is pressed to go on, the warning will be repeated every 30 minutes. The

  • Barco R9001300, Service Mode 10-4 5975948 RETRODATA 2100 210198 SERVICE IDENTIFICATION CHANGE PASSWORD CHANGE PROJ. ADDRESS CHANGE BAUDRATE PC RESET LAMP RUNTIME LAMP RUN TIME HISTORY PRESET INPUT BALANCE MORE ... assistance. Change Projector Address Every projector requires an individual address between 0 and 255. This address can be software installed. To change that address, press the control disc forwards or backwards to highlight Change Proj. Address and press ENTER. The Change Projector Address menu will be displayed and the a

  • 2-2 Location and Function of Control 5975948 RETRO DATA 2100 121297 Rear Input Panel Description & Function 01 Power switch :Main power switch for 'on and off' control.. 02 Stby : Stand by button : - To initiate remote power up operation. - To stop projection without main power off. 03 Projector Pilot Lamp : indicates the status of the projector. - Unlit : mains (power) switch

  • 8-11 Random Access Adjustment Mode 5975948 RETRODATA 2100 210198 Select with ê or é then <ENTER> <EXIT> to return. BLANKING BLANKING [ON] TOP BOTTOM LEFT RIGHT RESET Bottom blanking Top blanking Right blanking Left blanking Blanking adjustments affect only the edges of the projected image and are used to frame the projected image on to the sc

  • Barco R9001300, 11-2 Optional Equipment 5975948 RETRODATA 2100 210198 Adapter and Communication CablesLCD Projection Control Software for Windows The LCD Projection Control Software is a highly integrated application that allows you to effectively manage and control your BARCO Retro Projectors via your PC. It includes a robust feature set that allows for direct control of all of the projector's functions via an RS232 serial cable. It allows for the simultaneous control of groups of projectors. The software is invaluable durin

Related Products and Documents (TV):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Chubb MONITOR AFx Operation & user’s manual chubb/monitor-afx-6B2.pdf 25 Apr 2023 58
2 Smeg SC35 User manual manual smeg/sc35-FFV.pdf 25 Mar 2023 6 0.59 Mb
3 Haier 21F6B-T Owner's manual haier/21f6b-t-QN3.pdf 08 Jul 2023 32 1.67 Mb
4 jWIN JX-CD935 Operation & user’s manual jwin/jx-cd935-6X8.pdf 29 Jan 2024 7
5 HP PSC 700 Brochure hp/psc-700-OZS.pdf 01 Sep 2022 1 0.06 Mb
6 Melitta CAFFEO CI Operating instructions manual melitta/caffeo-ci-CW8.pdf 19 Apr 2023 45

Similar Resources:

  • Grundig

    T70-1020(A)

    (15 pages)
    T70-1020(A)ContentsBasic TV functionsManual tuningSetting lock codeTeletext featuresFault finding guideInformation & specificationGrundig T70 1020 Av2.qxd 15/11/01 13:55 Page 1 …
  • Mitsubishi Electric

    WD-C657

    (84 pages)
    DLP® HIGH-DEFINITION TELEVISIONMODELSC SeriesWD-C657Y SeriesWD-Y577, WD-Y657733 SeriesWD-57733, WD-65733, WD-73733734 SeriesWD-57734, WD-65734, WD-73734OWNER’S GUIDEt 'PSRVFTUJPOT 7JTJUPVSXFCTJUFBUXXXNJUTVCJTIJUWDPN &NBJMVTBU.%&"TFSWJDF!NEFBDPN $BMM$POTVNFS3FMBUJP …
  • LG

    CF-21Q20EH

    (30 pages)
    COLOR TVSERVICE MANUALCAUTIONBEFORE SERVICING THE CHASSIS,READ THE SAFETY PRECAUTIONS IN THIS MANUAL.CHASSIS : MC-014AMODEL:RF-21FA20/Q/PQ MODEL:CF-21Q20EHwebsite:http://biz.LGservice.come-mail:http://www.LGEservice.com/techsup.html …
  • Toshiba

    36AX61

    (50 pages)
    Color Television36AX61Owner’s ManualReferenceReferenceWelcome toToshibaConnectingyour TVUsing theRemote ControlSetting upyour TVUsing the TV’sFeaturesAppendixIndex© 2002 TOSHIBA CORPORATIONAll Rights Reserved.® 23565247AISO14001FILENo.A9645TOSHIBAAMERICACONSUMERPRODUCTS,INC. …
  • LG

    LM61

    (86 pages)
    OWNER’S MANUALLED LCD TV / LCD TVPlease read this manual carefully before operating your set and retain it for future reference.www.lg.comLM61**LM58**LM34**LS56**CM96**P/NO : MFL67416302 (1207-REV03)Printed in Korea …
  • Toshiba

    52XV645

    (2 pages)
    LEADING THE WAY IN HOME ENTERTAINMENT INNOVATION52XV645U1080p Full HD LCD TVwith ClearFrame™ 120HzLEADING THE WAY IN HOME ENTERTAINMENT INNOVATION52XV645U 52.0” diagonal 1080p HD LCD TV with ClearFrame™ 120HzPRELIMINARYADVANTAGE• 1080p Full HD CineSpeed™ Display• ClearFrame™ 120Hz with 5:5 Pull-Down Option• 50,000:1 Dynamic Contrast Rati …

Comments, Questions and Opinions: