BeiJer T21C Installation Manual

Text of BeiJer T21C User Guide:

• BeiJer T21C, Additional Installation Tips A good solution may be to use a shielded Ethernet cable, but to connect the shield at one e nd only. One option is to break the shield, see 3 in drawing above. A more elegant method is to expand the shielded Ethernet cabling with a piece of unshielded Ethernet cable, see 4 in drawing a bove. The shield can be grounded via an external 0.1 μF/250 V plastic capacitor, see 5 in drawing above. This will connect the HF transients to ground. BeijerElectronics, MAEN084E 27

• BeiJer T21C, Foreword InstallationmanualforT21C Foreword All operator panels are developed to satisfy the demands of human-machine communication. Built-in functions such as displaying and controlling text, dynamic indication, time channels, alarm and recipe handling are included. The operator panel works primarily in an object-oriented way, making it e asy to understand and use. Configuration is carried out on a PC using the iX Developer. Theprojectcanthenbetransferredandstoredintheoperatorpanelitself. Various types of a utomation equipment such as PLCs, servos or drives can be connected to the operator panels. In this manual, the term “th

• BeiJer T21C, Hardware Replacement 3.2 Replacingthe2.5”SATAMass Storage The following is needed: • A new 2.5” SATA mass storage • A T X10 Torx screwdriver Note: MakesuretouseadequateESDprotection. Follow the steps below to replace the 2.5” S ATA mass storage: 1. Power off the operator panel. 2. Remove the front frame assembly by removing the eight M3x8 Torx screws on the back cover assembly. Caution: Duringdisassembly,itisimportanttotakecareofthecablebetweenthefrontandthe rearpart. Ifyoudisconnectacable,besurethattherightcablewillbeintheright positionwhena

• BeiJer T21C, Hardware Replacement 3.3 ReplacingaCompactFlashorCFast MemoryCard The following is needed: • A new CompactFlash or CFast memory card. • A T X10 Torx screwdriver Note: MakesuretouseadequateESDprotection. Follow the steps belowto replace a memory card: 1. Power off the operator panel. 2. Follow the instr uctions in chapter Replacing the 2.5” SATA Mass Storage to removethefrontframeassembly. 3. Install the new memory card in its intended slot illustrated in figure below. 1. 2.5” SATA mass storage 2. CompactFlash slot 3. CFast slot 4. Reassemble in reverse order. BeijerElectronics, MAEN084E 14

• BeiJer T21C, Additional Installation Tips 7.3 ToAchieveBetterEMCProtection • Use shielded cables for RS232 communication. • Use twisted pair and shielded cabling for RS422 and RS485. • Use the cabling intended for the bus type; Ethernet, Profibus, CC-Link, CAN, Device Net etc. • Install and connect according to applicable specifications for the relevant bus standard. • Use shielded cabling for Ethernet, preferably with foil and a braided shield. • D-sub covers should b e shielded, and the shield should be connected

• BeiJer T21C, Installation 4. Connect the cables in the specified order, according to the drawing and steps below. Caution: • Theoperatorpanelmustbebroughttoambienttemperaturebeforeitisstarted up. Ifcondensationforms,ensurethattheoperatorpanelisdrybeforeconnecting ittothepoweroutlet. • Ensurethattheoperatorpanelandthecontrollersystemhavethesameelectrical grounding(referencevoltagelevel),otherwiseerrorsincommunicationmay occur. • Ensurethatthevoltageandpolarityofthepowersourceiscorrect. • Separatehighvoltagecablesfromsignalandsupplycab

• BeiJer T21C, Hardware Replacement 5. Remove the hard disk drive from the hard drive connection on the CPU board. 6. Reassemble with the new hard disk drive in reverse order. 1. 2.5” SATA mass storage 2. CompactFlash slot 3. CFast slot BeijerElectronics, MAEN084E 13

• BeiJer T21C, Hardware Replacement 4. Remove the fan by removing the two M4x35 Torx screws. 5. Reassemble with ne w fan and filter in reverse order. Use a maximum torque of 0.4 Nm when fastening the fan screws. BeijerElectronics, MAEN084E 11

• BeiJer T21C, Installation 2.2.1 ConnectionstotheController For information about the cables to be used when connecting the operator panel to the controller, please refer to the help file for the driver in question. 2.2.2 OtherConnectionsandPeripherals Cables, peripheral equipment and accessories must be suitable for the application and its environment. For further details or recommendations, please refer to the supplier. BeijerElectronics, MAEN084E 9

• BeiJer T21C, Safety Precautions • Make sure that the voltage and polarity of the power source is correct before connecting the operator panel to the power outlet. • Peripheral equipment must be appropriate for the application and location. 1.3 DuringUse • Keep the operator panel clean. • Emergency stop and other safety functions may not be co ntrolled from the operator panel. • Do not use excessive force or sharp objects when operating the touchscreen. 1.4 ServiceandMaintenance • Only qualifi ed personnel should carry out repairs. �

• BeiJer T21C, Additional Installation Tips 7.6 CableandBusTerminationRS485 • If maximum transfer distance and maximum transfer speed is needed, shielded and twisted pair cable should be used. The mutual capacitance may not exceed 52.5 pF/m, and the cable area should be at least 0.25 mm 2 (AWG 24). • 0 V, the reference voltage for communication should be included in the cabling. With two-way communication use two pairs; one pair for communication and one pair for 0 V. • The shield mus t be grounded at one end. The other end is usually grounded, but with longer distances or when there is a difference in the ground potential, theshieldshouldbeconnectedtothegroundvia0.

• BeiJer T21C, Additional Installation Tips 7.7 BootPriority The boot priority is the order in which the hardware storage devices are read. Pressing F7 during boot will display a drop down menu with all available bootable devices. A change of the boot priority is only temporary. On next startup the boot priority will be restored back to the factory setting. 7.8 EnteringBIOS Caution: Unlessyouareanexpertcomputeruser,donotchangetheBIOSsettingsforthis program. Certainchangescancauseyouroperatorpaneltoworkincorrectly. Note: BeforeusingBIOSsetup,itisrecommendedtowritedownt h

• Safety Precautions 1SafetyPrecautions Both the installer and the owner and/or operator of the operator panel must read and understand this installation manual. 1.1 General • Read the safety precautions carefully. • Check the delivery for transportation damage. If damage is found, notify the supplier as s oon as possible. • The supplier is not responsible for modified,

• BeiJer T21C, Chemical Resistance 5.2.2 TouchScreenSurface The touch screen surface on the operato r panel withstands exposure to the following solvents without visible change: Solvents Time Acetone 10minutes Isopropanol 10minutes Toluene 5 hours 5.2.3 TouchscreenProtectiveFilm Autotex It is recommended to use the Autoflex EBA 180Ltouch display protection film, that can be ordered from Beijer Electronics. OutdoorUse In common with all polyester based films, Autoflex EBA 180L i snotsuitablefor use in c onditions of long-term exposure to direct sunlig ht. Note: Thelayerstructureofthetouchscreencontainsairandinrarecasesappearanceof bubblescanarise. Thisispurelycos

• BeiJer T21C, Technical Data Parameter T21C Powersupply DCinputrange: 18to32VDC(140W)ATXstandard CE:Thepowersupplymustconformwiththerequirements accordingtoIEC60950andIEC61558-2-4. ULandcUL:Thepowersupplymustconformwiththe requirementsforclassIIpowersupplies. Display TFT-LCDwithLEDbacklight. 1920×1080pixels, 16.7millioncolors VGA 1×VGA:resolutionmax. 2048×1536@75Hz DVI 1×DVI-DsingleLink: Resolutionmax. 1600×1200or 1920×1200(withreducedblanking) Activeareaof display,W×H 476.64×268.11mm Operating temperature 0°Cto+50°C Storagetemperature -20°Cto+70°C Relativehumidity <85%non-condensed Approvalsand certifications Informationisavailableonthewebsit

• BeiJer T21C, Installation 2.2 InstallationProcess The following is needed: • ATorxTX7screwdriver 1. Unpack and check the delivery. If damage is found, notify the supplier. Note: Placetheoperatorpanelonastablesurfaceduringinstallation. Droppingthepanelorlettingitfallmaycausedamage. 2. To cut a correct opening for the operator panel, use the cut out dimensions in the outline drawing. A separate cut out drawing is available for download from the Beijer Electronics web site. For more information, see sections Operator Panel Drawings and Technical Data. 3. Secure the operator panel in position by screwing the M4 Torx screw, allowing the built-in bra

• BeiJer T21C, Installation 2Installation 2.1 SpaceRequirements • Maximum installation plate thickness: 8 mm • Space requirements in millimeters when installing the operator panel: 556 mm 347 mm 50 mm 100 mm 50 mm 100 mm 100 mm Note: Thedimensionsonthedrawingare notproportional. Caution: Theopeningsontheenclosureareforairconvection. Donotcovertheseopenings. BeijerElectronics, MAEN084E 6

• Chemical Resistance 5 ChemicalResistance 5.1 MetalCasing The frame and casing material is powder-coated aluminum. This powder paint withstands exposure to the following chemicals without visible change: Aceticacid10% Phosphoricacid4% Citricacid10% Phosphoricacid10% Diesel Seawater Distilledwater Sodiumchloride2% Edibleoil Sodiumchloride20% Fueloil Sulphuricacid20% Hydrogenp e ro

• BeiJer T21C, Operator Panel Drawings 6 Opera torPanelDrawings 6.1 Connectors 12345678 9 Pos. Connector Description 1DVI Externalmonitor 2VGA Externalmonitor 3 COM3/4 CommunicationPo rts 4 COM1/2 CommunicationPo rts 5 LANPortB 1×10/100/1000Base-T(shieldedRJ45);Intel82574 6 LANPortA 1×10/100/1000Base-T(shieldedRJ45);Intel82574 7 USB 2×USBHost2.0,maxoutputcurrent500mA 8 USB 2×USBHost2.0,maxoutputcurrent500mA 9 Powersupply DCinputrange: 18-32VDC(140W)ATXstandard 6.2 CommunicationPorts Serialport,9-pinfemale Serialport,9 -pinfemale Pin COM1 COM2 COM3 COM4 1- RS422Tx+ RS485Tx+/Rx+ - RS422Tx+ RS485Tx+/Rx+ 2 RS232RxD - RS232RxD - 3 RS232TxD - RS232TxD - 4 - RS422Rx+ - RS422Rx+ 5 GND GND

• BeiJer T21C, Additional Installation Tips 7.4 AmbientTemperature The maximum ambient temperature for the operator panel is provided in the specifications. The ambient temperat ure refers to the temperature in the device cabinet which cools the operator panel’s electronics. Operator panel Power Power Power 30 °C outside To p 50 °C inside Bottom 40 °C inside Middle 45 °C inside Airflow Axial fan 120 x 120 mm Inmostcases,theambienttemperaturefortheoperatorpanelissignificantly higher than the device cabinet’s ambient temperature. If the cabinet is tall and there are a number of heat-generating devices, the temperature at the top of the cabin et will b

• Technical Data 4TechnicalData Parameter T21C Frontpanel,W×H×D 556×347×87mm Cutoutdimensions, W×H 539×331mm Mountingdepth 79mm(179mmincludingclearance) Standalonemounting VESA100×100 Note: MaximumscrewlengthforVESAmountingis5.5mm. Usageoflongerscrewsmayleadtodamage. Frontpanelseal IP65 Rearpanelseal IP20 Touchscreen material Polyeste ronglass,resistive. Overlay:

More Instructions:

BeiJer T21C Installation manual 23-10-2022 34

DOWNLOAD

Related Products and Documents (Monitor):

Comparable Devices:

Similar Resources:

• Dell S2440L (1 pages) (DELL P/N: YY96C Rev. A00)P/N: 4J.1SR01.001S2440L43561 211Dell™S2440LDRIVERS AND DOCUMENTATIONP/N HGF1Y Rev. A00 July 2012Contents:5B.1SR01.001Made in ChinaDellInc.Allrightsreserved.barcode2©012• Device drivers• Setup Guide• User’s Guide• Dell Display Manager SoftwareDell™S2440LDRIVERS AND DOCUMENTATIONP/N HGF1Y Rev. A00 July 2012Contents:5B. …

• NEC NP4000 (2 pages) © NEC Display Solutions, Ltd. 2007 Ver. 1 04/07 Printed in China Connect the projector. Schließen Sie den Projektor an. Connecter le projecteur. Connettere il proiettore. Conecte el proyector. Anslut projektorn. 프로젝터를 연결합니다. Connect the supplied power cable (A). Press the main power switch (B). Schließen Sie das mitgelieferte …

• Free The Tone LDP-1 (4 pages) OWNER’S MANUALVer 1.0 CautionDo not use or store the unit in environments where it will be exposed to:Extreme temperatures (direct rays of the sun, heat sources such as radiators or stoves.)High humidity or moisture.Excessive dust or sand.Excessive vibration or shock.Whenever leaving the unit unattended for long periods, be sure to unplug the AC adapter fr …

• Topaz SL SERIES (42 pages) Design Led – Solutions Driven 42” multimedia Full HD TOPAZ™ SL Display Hardware User Manual TOPAZ™ SL Series Hardware User Manual …

• Acura Embedded Systems ACUBRITE 15-NAV (6 pages) AcuBrite 15-NAV User Guide AcuBrite 15-NAV User Guide ACUBRITE ™ 15-NAV Sunlight Readable Marine Certified Monitor User’s Guide Ed …

• LG Flatron 795FT Plus (13 pages) A1IntroductionThank you for purchasing a high resolution monitor. It will give you highresolution performance and convenient reliable operation in a variety ofvideo operating modes.FeaturesThe monitor is a 17 inches (16.0 inches viewable ) intelligent, microprocessorbased monitor compatible with most analog RGB (Red, Green, Blue) displaystandards, including …

Comments, Questions and Opinions: