Casio QV-R62 Operation & User’s Manual

Text of Casio QV-R62 User Guide:

• Casio QV-R62, 112 PLAYBACK 4. Use the zoom controller to make the cropping boundary larger or smaller. • The size of the cropping boundary depends on the size of the image on the display. 5. Use [], [], [], and [] to move the cropping boundary up, down, left, or right until the area of the image you want to extract is within the boundary. 6. Press [SET] to extract the part of the image enclosed in the cropping boundary. • If you want to cancel the procedure at any point, press [MENU]. IMPORTANT! • Cropping an image creates a new file that contains t

• Casio QV-R62, GETTING READY 41 ■ AC Adaptor Precautions • Be sure to turn off power before connecting or disconnecting the AC adaptor. • Always turn camera power off before disconnecting the AC adaptor, even if the camera has batteries installed. If you don’t, the camera will turn off automatically when you disconnect the AC adaptor. You also run the risk of damaging the camera whenever you disconnect the AC adaptor without first turning power off. • The AC adaptor may become warm to touch after extended periods of use. This is normal and is not cause for al

• PRINTING IMAGES 156 10 . Use [왖] and [왔] to select the paper size you want to use for printing, and then press [SET]. • The following are the print sizes that are available. 3.5˝ × 5˝ 5˝ × 7˝ A4 4˝ × 6˝ By Printer • Selecting “By Printer” prints using the paper size selected on the printer. • Available paper size settings depend on the connected pr

• OTHER SETTINGS 138 Using World Time You can use the World Time screen to view a time zone that is different from the home time zone when you go on a trip, etc. World Time can display the time in one of 162 cities in 32 time zones. To display the World Time screen 1. In the REC mode or the PLAY mode, press [MENU]. 2. Select the “Set Up” tab, select “World Time”, an

• Casio QV-R62, 63 BASIC IMAGE RECORDING Changing the Flash Intensity Setting Perform the following steps to change the flash intensity setting. 1. In the REC mode, press [MENU]. 2. Use [왗] and [왘] to select the “REC” tab. 3. Use [왖] and [왔] to select “Flash Intensity”, and then press [왘]. 4. Use [왖] and [왔] to select the setting you want, and then press [SET]. IMPORTANT! • Flash intensity may not change if the subject is too far or too close to the camera. To make flash intensity: Stronger Normal Weaker Select this setting: +2 +1 0 –1 –2 Using Flash Assist Recording a subject that is outside the flash range can ca

• Casio QV-R62, QUICK START GUIDE 22 1. Press the power button to turn on the camera. 2. Use [], [], [], and [] to select the language you want. 3. Press [SET] to register the language setting. 4. Use [], [], [], and [] to select the geographical area you want, and then press [SET]. 5. Use [] and [] to select the city you want, and then press [SET]. 1 2, 3, 4, 5, 6, 7, 8, 9 To configure display language and clock settings • Be sure to configure the following settings before using the camera to record images. (See page 47 for details.) 6. Use [] and [] to select the summer time (DST) setting you want, and then

• 73 OTHER RECORDING FUNCTIONS Using the Macro Mode The Macro mode lets you focus on close up subjects automatically. The automatic focus operation starts when you press the shutter button down half way. The following are the approximate focus ranges in the Macro mode. Ranges: 10cm to 70cm (3.9˝ to 27.6˝) at wide angle 60cm to 70cm (23.6˝ to 27.6˝) at telep

• Casio QV-R62, 84 OTHER RECORDING FUNCTIONS IMPORTANT! • BESTSHOT scenes were not recorded using this camera. They are provided as samples only. • Images recorded using a BESTSHOT scene may not produce the results you expected due to shooting conditions and other factors. • After selecting a BESTSHOT scene, you can change to a different one by pressing [SET] and then using [] and [] to scroll through available scenes. When the one you want is displayed, press [SET]. • You can change the camera settings

• Casio QV-R62, INTRODUCTION 9 ■ Copyright Restrictions Except for the purpose of your own personal enjoyment, unauthorized copying of snapshot files and movie files violates copyright laws and international contracts. Distribution to third parties of such files over the Internet without permission of the copyright holder, whether for profit or for free, violates copyright laws and international contracts. Features • 6 million effective pixels The CCD provides 6.37 million total pixels of very high- resolution for crisp, clear, prints and display images. • 2.0-inch TFT color LCD mo

• Casio QV-R62, 59 BASIC IMAGE RECORDING Digital Zoom Digital zoom is activated after you reach the maximum optical zoom factor (3X). It enlarges the part of the image at the center of the image screen. The range of the digital zoom factor is shown below. Digital Zoom Factor Range: 3X to 12X (in combination with optical zoom) 1. In the REC mode, press [MENU]. 2. Use [왗] and [왘] to select the “REC” tab. 3. Use [왖] and [왔] to select “Digital Zoom”, and then press [왘]. 4. Use [왖] and [왔] to select “On”, and then press [S

• Casio QV-R62, 92 OTHER RECORDING FUNCTIONS IMPORTANT! • Before recording, compose the image so outline of the item you want to record fits entirely within the monitor screen. The camera will not be able to detect the shape of the subject correctly unless it is enclosed entirely within the monitor screen. • The camera also will be unable to detect the shape of the subject if it is the same color as the background. Make sure the subject is against a background that allows the outline of the subject to stand out. NOTE • When the camera is at an angle to a business card or document it is recording, the shape of the business card o

• Casio QV-R62, 60 BASIC IMAGE RECORDING IMPORTANT! • Digital zoom is disabled whenever the monitor screen is turned off (page 31). • When you perform a digital zoom operation, the camera manipulates the image data to enlarge the center of the image. Unlike optical zoom, an image enlarged with digital zoom appears coarser than the original. Using the Flash Perform the following steps to select the flash mode you want to use. • The approximate effective range of the flash is shown below. Wide Angle: Approximately 0.6 meters to 2.6 meters (2.0´ to

• Casio QV-R62, GETTING READY 46 To do this: Apply the setting and exit the menu screen. Apply the setting and return to feature selection in step 4. Apply the setting and return to tab selection in step 3. Perform this key operation: Press [SET]. Press []. 1. Press []. 2. Use [] to move back up to tab selection. 6. Perform one of the following operations to apply the setting you configured. • See “Menu Reference” on page 192 for more information about menus. 3. Press [] or [] to select the tab you want, and then press [SET] to move the selection cursor from the tab to the settings. 4. Use [] and [] to select the feature whose setting you want to configure, and then press [�

• Casio QV-R62, 118 PLAYBACK To specify the slideshow images 1. Use [] and [] to select “Images”, and then press []. 2. Use [] and [] to select the setting you want, and then press [SET]. 3. Use [] and [] to select “Start”, and then press [SET]. • This starts the slideshow. To do this: Include all files in file memory in the slideshow Display a single file Include all files in the FAVORITE folder (page 126) in the slideshow Select this setting: All images One Image Favorites ■ Selecting a Single Image for a Slideshow When you select “One image” as the slideshow type, the slideshow displays only one image, without changin

• 94 OTHER RECORDING FUNCTIONS 1. Enter the REC Mode, and select “ Movie” as the recording mode (page 50). • This enters the Movie Mode and causes “ ” to appear on the monitor screen. • You can use the key customization feature (page 104) to configure the camera to enter the Movie Mode whenever you press [] or [] while in the REC mode. 2. Point

• Casio QV-R62, FILE MANAGEMENT 129 To delete a file from the FAVORITE folder 1. In the PLAY mode, press [MENU]. 2. Select the “PLAY” tab, select “Favorites”, and then press []. 3. Use [] and [] to select “Show”, and then press [SET]. 4. Press [] ( ). 5. Use [] and [] to select the file you want to delete from the FAVORITE folder. 6. Use [] and [] to select “Delete”, and then press [SET]. • To exit the file delete operation without deleting anything, select “Cancel”. 7. After deleting all of the files you want, use [] and [

• Casio QV-R62, APPENDIX 200 Other Symptom Possible Cause Action All buttons and switches are disabled. Monitor screen is off. Cannot transfer files over a USB connection. Circuit problem caused by electrostatic charge, impact, etc. while the camera was connected to another device. 1) USB communication is in progress. 2) The monitor screen is turned off (in the REC mode). 1) USB cable is not connected securely. 2) USB driver is not installed. 3) Camera is turned off. Remove the batteries from the camera, reinsert them, and then try again. 1) After confirming that the computer is n

• Casio QV-R62, OTHER SETTINGS 142 Configuring [ ] (REC) and [ ] (PLAY) Power On/Off Functions You can use the following procedures to configure [ ] (REC) and [ ] (PLAY) so power turns on or off whenever they are pressed. 1. In the REC mode or the PLAY mode, press [MENU]. 2. Select the “Set Up” tab, select “REC/PLAY”, and then press []. 3. Use [] and [] to select the setting you want, and then press [SET]. IMPORTANT! • When “Power On/Off” is selected, pressing [ ] (REC) in the REC mode or [ ] (PLAY) in the

• Casio QV-R62, 96 OTHER RECORDING FUNCTIONS • When the histogram is too far to the left, it means that there are too many dark pixels. This type of histogram results when the overall image is dark. A histogram that is too far to the left may result in “black out” of the dark areas of an image. • When the histogram is too far to the right, it means that there are too many light pixels. This type of histogram results when the overall image is light. A histogram that is too far to the right may result in “white out” of the light areas of an image. • A centered histogr

• Casio QV-R62, APPENDIX 195 REC mode Operation Lamp Self-timer Lamp Green Lit Lit Pattern 3 Lit Pattern 2 Pattern 1 Red Pattern 3 Lit Pattern 1 Pattern 2 Lit Red Pattern 1 Pattern 2 Operational (Power on, recording enabled) Flash is charging. Flash charging is complete. Auto Focus operation was successful. Cannot Auto Focus. Monitor screen is off. Storing image Storing movie data / processing image data Self-timer countdown (10 to 3 seconds) Self-timer countdown (3 to 0 seconds) Cannot charge flash. Memory card problem / Memory card is unformatted. / BESTSHOT s

• INTRODUCTION 13 ■ Connections • Never plug any devices that are not specified for use with this camera into connectors. Connecting a non- specified device creates the risk of fire and electric shock. ■ Transport • Never operate the camera inside of an aircraft or anywhere else where operation of such devices is restricted. Improper use creates the risk of serious accident. ■ Smoke, a

• OTHER SETTINGS 135 Stopping the Alarm When an alarm time is reached while the camera is turned off, the alarm will sound for about one minute (or until you stop it), and then the camera will turn on. To stop the alarm after it starts to sound, press any button. IMPORTANT! • Note that the alarm does not sound if the alarm time is reached when any one of the following conditions exists

• Casio QV-R62, 50 BASIC IMAGE RECORDING BASIC IMAGE RECORDING This section describes the basic procedure for recording an image. Recording an Image Specifying the Recording Mode Your CASIO digital camera has three recording modes, each of which is described below. Before recording an image, use the procedure below to select the applicable recording mode. • (Snapshot mode) Use this mode to record still images. This is the mode you should normally use for image recording. • (BESTSHOT mode) This mode makes camera setup as easy as selecting the applicable sample scene. Simply select one of 23 sample scenes, and the camera will autom

• Casio QV-R62, USING THE CAMERA WITH A COMPUTER 183 Installing the Software from the CD-ROM Your digital camera comes bundled with useful applications for using it in combination with a computer. Install the applications you need on your computer. About the bundled CD-ROM The CD-ROM that comes bundled with the camera contains the applications described below. Installation of these applications is optional, and you should install only the ones you want to use. USB Driver for Mass Storage (for Windows) This is t

• Casio QV-R62, INTRODUCTION 15 ■ Locations To Be Avoided • Never leave the camera in any of the following types of locations. Doing so creates the risk of fire and electric shock. — Areas subject to large amounts of humidity or dust — Food preparation areas or other locations where oil smoke is present — Near heaters, on a heated carpet, in areas exposed to direct sunlight, in a closed vehicle parked in the sun, or other areas subject to very high temperatures • Never place the camera on an unstable surface, on a high shelf, etc. Doing so can cause the camera to fall, creati

• Casio QV-R62, GETTING READY 40 Using AC Power You need to purchase the optionally available AC adaptor (AD-C30) in order to be able to power the camera using AC power. 1. Connect the AC power cord to the AC adaptor. 2. Open the camera’s terminal cover and connect the AC adaptor to the port marked [DC IN 3V]. 3. Plug the AC power cord into an electrical outlet. Terminal cover [DC IN 3V] AC power cord AC adaptor Plug

• Casio QV-R62, OTHER SETTINGS 133 IMPORTANT! • Only a snapshot (JPEG) or movie (AVI) file can be used as the power down image. • Note that the power down image feature works only with images recorded with this camera. The power down image feature may not operate properly when another type of image is specified as the power down image. • Formatting the camera’s flash memory deletes the power down image (page 143). • When both a still image and a movie are present for the power down image, only the movie is used. • Note that a power down image display opera

• Casio QV-R62, OTHER SETTINGS 131 Specifying an Image for the Startup Screen You can specify an image you recorded as the startup screen image, which causes it to appear on the monitor screen for about two seconds whenever you press the power button or [ ] (REC) to turn on the camera. The startup screen image does not appear if you press [ ] (PLAY) to turn on the camera. 1. In the REC mode or the PLAY mode, press [MENU]. 2. Select the “Set Up” tab, select “Startup”, and then press []. 3. Use [] and [] to display the image you want to use as the startup image. 4. Use [] and [] to change the setting, and then press [SET]. Select this setting: On Off To do this: Use t

More Instructions:

Casio QV-R62 Settings manual 25-10-2022 1

DOWNLOAD

Related Products and Documents (Digital Camera):

Comparable Devices:

Similar Resources:

• FujiFilm FinePix AX650 (2 pages) Point and shoot simplicity The FinePix AX650 combines great image quality and intelligent, user-friendly features into a stylish, compact body. Sporting a 16 megapixel resolution sensor, a 5x FUJINON optical zoom lens, a 2.7inch LCD screen and an array of exciting features, the AX650 from FUJIFILM, is ready when you are. With a choice of 4 bright colours an …

• Alecto DC-KIT (2 pages) GEBRUIKSAANWIJZINGInstallatie:Bepaal de montageplaats van de camera.Buiten camera:Houd de montagevoet tegen deze plaats en teken de boorgaten af.Bevestig de camera met behulp van de meegeleverde schroeven.Binnen camera:Schroef twee schroeven horizontaal 80 mm uit elkaar, eventueel met pluggen, in de wand, of maak gebruik van het meegeleverde sjabloon. Zorg d …

• Epson P-2000 - Multimedia Storage Viewer (1 pages) Upgrading Your Epson P-2000To take advantage of the latest enhancements for your P-2000, you may be able to upgrade your viewer’s firmware. To find out if you have the latest firmware, turn on your P-2000, go to the Home screen, and click the Settings icon. The firmware version is located in the lower-right corner, as shown.◗ If you see Ver. 02.02, you …

• Praktica Luxmedia Z360 (6 pages) LuxmediaUser ManualPRAKTICA International Ltd, 5 Century Point, Halifax Road, High Wycombe, HP12 3SL, United Kingdom www.praktica.com | [email protected] | +44(0)344 822 9940 …

• Samsung ES10 (82 pages) This Quick Start Manual has been specially designed to guide you through the basic functions and features of your device. Please read the Quick Start Manual and User Manual carefully to ensure safe and correct use.Quick Start ManualES10For more information, refer to the User Manual included on the supplied CD-ROM.ENG / FRE / TUR / T.CHI / IND / ARA / THA / …

• Minolta Auto Meter IV F (30 pages) -HHvMINOLTNO 1991 Minolta Camera Co., Ltd. under the BerneConvention and Universal Copyright Convention9222-8054-18IDFAP I ftinteC in Japan-MINOLTNAUTOE tNsTRUcTtoN MANUAL[r.l voor D'EMPLoI …

Comments, Questions and Opinions: