Manualios.com

Bewator FH07B Series Installation Instructions Manual

  • FH07B Series Security Camera
  • maKa3zNxtu6IM
  • Installation Instructions Manual
  • PDF / Adobe Acrobat Reader
  • 24

Bewator FH07B Series Manual Online:

4.25, 862 votes
Bewator FH07B Series User Manual
Bewator FH07B Series User Guide
Bewator FH07B Series Online Manual

Text of Bewator FH07B Series User Guide:

  • Bewator FH07B Series, FH07B Series Phoenix™ 7” Flameproof Camera Housing INS00306 Page 1 of 24 Installation Instructions Manual: INS00306 Issue: 3.0

  • FH07B Series Installation Instructions Issue 3.0 INS00306 Page 2 of 24 IMPORTANT NOTE Please thoroughly read these Instructions before installing the FH07B Series Phoenix™ 7” Flameproof Camera Housing. Table of Contents About This Manual ......................................................................................

  • FH07B Series Installation Instructions Issue 3.0 INS00306 Page 3 of 24 About This Manual This manual describes the following equipment, certified to the EC (ATEX) Directive 94/9/EC as II 2 GD (EEx d IIB T85°C): FH07B-40 Phoenix™ 7” diameter, IP67, Camera Housing (420 x114 x 93mm internal) c/w sunshield, demister ~ 23

  • Bewator FH07B Series, FH07B Series Installation Instructions Issue 3.0 INS00306 Page 4 of 24 • The mounting surface must be sufficiently solid and strong to take the complete weight of the assembly and take into account environmental aspects such as exposure to strong wind. • It is recommended that the bracket and column spacers detailed on Page 21 should be used, where appropriate. • As the mounting surface to which this housing could be attached is site dependent, Bewator Ltd. does not supply fixings for securing the base of the unit to its mounting surface. It is the responsibility of installers to

  • Bewator FH07B Series, FH07B Series Installation Instructions Issue 3.0 INS00306 Page 5 of 24 Introduction General Description Hazardous Areas The Phoenix™ 7” FH07B Series Flameproof Camera Housing is certified to the EC (ATEX) Directive 94/9/EC for use in hazardous areas. A hazardous area is defined as an area in which explosive atmospheres are, or may be expected to be, present in quantities such as to require special precautions for the construction and use of electrical equipment. An explosive atmosphere consists of a mixture of flammable substances with air in the form of gas, vapour, mi

  • Bewator FH07B Series, FH07B Series Installation Instructions Issue 3.0 INS00306 Page 6 of 24 Certification EC (ATEX) Directive 94/9/EC Certification is to :- CE Marking. Bewator Ltd. Declaration Of Conformity. Bewator Ltd. Quality System certified to ISO9001. Specific explosion protection mark. II Equipment group II. Group II comprises equipment intended for use in places liable to be endangered by explosive atmospheres, other than mining applications. 2 Equipment category 2. Equipment in this category is intended for use in areas in which explosive atmospheres caus

  • FH07B Series Installation Instructions Issue 3.0 INS00306 Page 7 of 24 Equipment Marking The equipment has a special yellow label attached to the outside of the Rear Cap Assembly. The label includes the following: 1180 II 2 GD EEx d IIB T85°C Equipment Description • The housing is manufactured using a 7” external diameter extruded a

  • Bewator FH07B Series, FH07B Series Installation Instructions Issue 3.0 INS00306 Page 8 of 24 Figure 1 Typical Flameproof Camera Housing Figure 2 Detail Showing Flame Path Zone Locations

  • Bewator FH07B Series, FH07B Series Installation Instructions Issue 3.0 INS00306 Page 9 of 24 Contents of Package The product should reach you in perfect working order. If the unit is damaged in any way or if the supplied kit is incomplete, please contact Bewator Ltd. immediately. 1 x FH07B Series Camera Housing, including Sunshield, fitted with optional accessories. 1 x General Packing Kit comprising: 4 x M5 x 16 Hex Socket Button Head Screw. 4 x M5 Nylon Washer. 3 x M5 x 60mm M5 Hex Head Special - Rear Cap Removal Screw. 2 x M6 x 70 Cap Head - Rear Cap Fitting Guide Screw. 4 x Cable Gland (Hawke Cable Gland Type 501/421). 1 x Installation Instructions INS00306.

  • Bewator FH07B Series, FH07B Series Installation Instructions Issue 3.0 INS00306 Page 10 of 24 Suggested Tools The following tools are suggested for the installation of a FH07B Series Flameproof Camera Housing: • 3mm A/F (across flats) Allen key • 5mm A/F (across flats) Allen key • 10mm A/F (across flats) Allen key • No 1 ‘Posidrive’ screwdriver • Torque wrench set to 4.5Nm • Rubber hammer • 8mm A/F (across flats) ring spanner • Small flat bladed (electrical) screwdriver.

  • FH07B Series Installation Instructions Issue 3.0 INS00306 Page 11 of 24 Ordering the FH07B Series Unit Certification Requirements For The Camera/Lens To ensure compliance with the certification to the EC ‘ATEX’ Directive 94/9/EC Equipment- group II, Category 2, the Camera/Lens to be fitted into the FH07B Series Camera Housing MUST adhere with the maximum re

  • Bewator FH07B Series, INS00306 Page 12 of 24 Installing the FH07B Series Unit Removing The Rear Cap Assembly 1. This procedure should ONLY be performed in the workshop. 2. NOTE: It is recommended that the Front Cap Assembly is NOT removed at any time. 3. Remove the Rear Cap Assembly. a) If the Wiper Unit Kit (FH07W) is fitted, ensure that the wiper arm is resting in the PARK position. (See Figure 1.) b) Remove the 6 off M6 x 25 Cap Head A4-80 stainless steel screws and star washers from around the periphery of the Rear C

  • Bewator FH07B Series, FH07B Series Installation Instructions Issue 3.0 INS00306 Page 13 of 24 Pre-installation Wiring General 1. This procedure should ONLY be performed in the workshop. 2. Note: Use only cable suitable for the application and that meets the standards required by the installation. 3. Ensure that the maximum cable distances are not exceeded. Cable Diameter Impedance Maximum Distance 0.50mm 2 50.4 Ohm/km 67 metres 0.75mm 2 32.3 Ohm/km 100 metres 1.00mm 2 19.9 Ohm/km 167 metres 4. Phoenix™ FH07B Series housings are supplied with four cable entries (M20 x 1.5 threaded) in the Rear Cap Assembly. Each threaded entry hole MUST be fitted either

  • Bewator FH07B Series, INS00306 Page 14 of 24 Wiring Requirements for FH07B Series Housings supplied WITHOUT any optional accessories fitted 1. Confirm that the special Earth wire is connected between the Earth Stud on the inside of the Rear Cap Assembly and the SUPPLY INPUT earth (E) terminal on the Terminal Block Assembly. 2. Confirm that the Heater cable is connected to the HEATER (N L) terminals on the Terminal Block Assembly. The L wire is connected via. the Thermostat, which is mounted on the inside of the Rear Cap Assembly. 3. The user supplied mains input c

  • Bewator FH07B Series, FH07B Series Installation Instructions Issue 3.0 INS00306 Page 15 of 24 Wiring Requirements for FH07B Series Housings supplied fitted with a Wiper Unit Kit (FH07W Series) 1. Confirm that the special Earth wire is connected between the Earth Stud on the inside of the Rear Cap Assembly and the SUPPLY INPUT earth (E) terminal on the Terminal Block Assembly. 2. Confirm that the Heater cable is connected to the HEATER (N L) terminals on the Terminal Block Assembly. The

  • Bewator FH07B Series, FH07B Series Installation Instructions Issue 3.0 INS00306 Page 16 of 24 Wiring Requirements for FH07B Housings supplied fitted with a 10 - function Telemetry Receiver Kit (FH07-RX210) 1. Note: All electrical connections to any external equipment (e.g. a PTZ unit) are via. the 10 - function Preset Receiver Assembly (RX210). The receiver is securely fitted to an integral mounting plate fixed on the Monorail. 2. Note: The 10 - function Preset Receiver offers both coaxial (“C” Type) and twisted pair (“D” Type) telemetry options, using plug-in modular circuit boards, as detailed in the Bewator Ltd. Installation Instructions (INS00054).

  • Bewator FH07B Series, FH07B Series Installation Instructions Issue 3.0 INS00306 Page 17 of 24 Wiring Requirements for FH07B Housings supplied fitted with a 17 - function Receiver Kit (FH07-RX217) 1. Note: The fitting of a 17 – function Receiver Kit (FH07-RX217) creates space limitations for the fitting of other items into the housing, which must be addressed. It is recommended that the 17 – function Receiver Kit should ONLY be fitted to a –40 (420mm) version of the Housing. 2. Note: The 17 - fu

  • FH07B Series Installation Instructions Issue 3.0 INS00306 Page 18 of 24 Refitting The Rear Cap Assembly And Fitting The Sunshield 1. Refitting the Rear Cap Assembly. Note: Before refitting the Rear Cap Assembly, test the Camera functions and check that the lens dust cover is removed! a) Take care that the ‘O’ ring seal is free from grit and dirt. Lightly

  • Bewator FH07B Series, FH07B Series Installation Instructions Issue 3.0 INS00306 Page 19 of 24 Figure 15 Fitting the Sunshield 2. Fitting the Sunshield. a) Carefully place the Sunshield in position on the Body, ensuring that the front of the Sunshield is at the front of the Body. b) Fit the 4 off M5 nylon washers and the 4 off M5 x 16 hex socket button head screws. (See Figure 15.) Locating The Unit 1. Please ensure that all equipment is suitable for the application and the environment for which it is intended. 2. Please take particular care that the inter-connec

  • Bewator FH07B Series, FH07B Series Installation Instructions Issue 3.0 INS00306 Page 20 of 24 Maintenance The following guidelines for maintenance should be observed: 1 Month After Installation All external fastenings and cables should be thoroughly checked for tightness, security and wear. 6 Monthly Checks All external fastenings and cables should be thoroughly checked for tightness, security and wear. Perform checks to ensure that cables are not fouling on any obstruction. Check cables for signs of wear. Replace as necessary. I

  • Bewator FH07B Series, FH07B Series Installation Instructions Issue 3.0 INS00306 Page 21 of 24 Specifications Mechanical Application Hazardous (Explosive) Atmospheres EC Directive 94/9/EC Certification: II 2 GD (EEx d IIB T85°C) EN 60529 Certification: IP67 Mounting a) Static: Wall mount using (optional) Wall Bracket, with or without Column Spacers: e.g. BH100 + BS100 b) Moving: Pan and Tilt (PTZ) Unit: e.g. FP50B Series FH07B-30 Series FH07B-40 Series Dimensions With Sunshield Weight Housing o

  • Bewator FH07B Series, FH07B Series Installation Instructions Issue 3.0 INS00306 Page 22 of 24 Mechanical Dimensions The physical dimensions for the FH07B Series Phoenix™ 7” Flameproof Camera Housing are shown below. All measurements are given in millimetres. Note: All specifications are subject to change without prior notice.

  • Bewator FH07B Series, FH07B Series Installation Instructions Issue 3.0 INS00306 Page 23 of 24 Wiring Diagram Note: These circuits are example layouts only. Refer to Bewator Ltd. for further detail.

  • Bewator FH07B Series, FH07B Series Installation Instructions Issue 3.0 INS00306 Page 24 of 24 Notes The Declaration of Conformity for this product range is available from Bewator Ltd., see below. It is also available for download from the Bewator Ltd. web site ( www.bewator.co.uk). Bewator Ltd. Albany Street, Newport, South Wales, United Kingdom, NP20 5XW. Telephone: +44 (0) 1633 821000, Fax: +44 (0) 1633 850893 Email: [email protected] : Internet: http://www.bewator.co.uk/ Customer Support Tel: +44 (0) 1633 820615 Whilst every effort has been made to ensure that all information contained in this document is correct at the time of publication, due to our policy of co

Related Products and Documents (Security Camera):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 FSR SPC-15X Owner's manual fsr/spc-15x-DKU.pdf 25 Dec 2022 5
2 ESCALADE LS2005 Owners assembly manual & operating instructions escalade/ls2005-C7M.pdf 12 Nov 2022 11
3 HP D5060 Setup manual hp/d5060-71N.pdf 09 Jul 2023 2
4 Sterling Plumbing 14619-3 Specification sheet sterling-plumbing/14619-3-G34.pdf 16 May 2023 2 0.05 Mb
5 Chevrolet Sonic 2012 Getting to know manual chevrolet/sonic-2012-CB6.pdf 12 Dec 2022 16 2.21 Mb
6 Accusplit AX625 Operating instructions accusplit/ax625-HOQ.pdf 07 May 2023 1 0.13 Mb

Similar Resources:

  • D-Link

    DCS-7110

    (60 pages)
    DCS-7110Documentation also available on CD and via …
  • Astrel Instruments

    AST16200-B

    (21 pages)
    Astrel Instruments AST8300-B / AST16200-B Astrel InstrumentsAST8300-B / AST16200-BGETTING STARTEDrev AGetting Started 1/21 rev A …
  • Digital Watchdog

    MEGAPIX DWC-MT94WI36T

    (2 pages)
    Default Login InformationUsername: admin Password: adminQuick Start Guide Quick Start GuideWHAT’S IN THE BOXQuick setup and Installation Guides1 setTapping Screws – 3pcs1 setMounting Template1Plastic Plugs– 3pcs1 setWaterproof Cap1 set Rubber Plug 1Hexagonal Wrench 0.07” (2mm)1DWC-MT94Wi28T DWC-MT94Wi36TSTEP 1 – PREPARING TO MOUNT THE CAMERASTEP 2 …
  • Lilin

    iMEGAPRO IPD2220-IVS

    (13 pages)
    IPD2220-IVSIPD2220ES/LD2222E1080P HD IVS Dome IP Camera1080P HD Dome IP Camera66-LD2222CSMQuick Installation GuideIPD6220ES (M12 MODEL)SD2222E1080P HD IVS Dome IP Camera1080P60 HD Dome IP CameraIPD6222ES (RJ-45 MODEL)1080P HD IVS Dome IP Camera …
  • Moog

    RHW7CN-3 SERIES

    (13 pages)
    www.videolarm.comR H W 7 C N - 3SView™ Vandal-Resistant Rugged (Outdoor Dome Housing)Installation and Operation Instructions for the following models:RHW7CN-3 7” Vandal-Resistant Outdoor dome housing with wall mount, rugged cast aluminum top and polycarbonate clear dome, with 24Vac input, heater/blower, with a SView network pan/tilt.RHP7CN …
  • Oxford Instruments

    ANDOR Zyla

    (2 pages)
    Unpack the CameraInstall Software (Solis or SDK)231Prepare your FacilityZyla Quick Start Guide - USB 3.0 ModelsHandle the camera and accessories with care. Use correct power supply and cables.Observe anti-static precautions when installing the controller card and camera.Store between -10°C and 50°C.Ensure 100 mm clearance around camera and power supply ven …

Comments, Questions and Opinions: