Audio bit Ten Advanced Manual

Text of Audio bit Ten User Guide:

• Audio bit Ten, ADVANCED MANUAL / bit Ten / 4 How to install the DRC (optional) DRC Warning: do not use aggressive cleaning agents or abrasive cloth to clean the display. Simply use a soft cotton cloth lightly damped with water. 4,2x20mm / 0,16”x0,78” 3. bit Ten D and DRC INSTALLATION External dimensions Mounting dimensions 68 mm / 2.68” 90 mm / 3.54” 35 mm / 1.38” Ø 2 mm / 1/8” 50 mm / 2” 16 mm / 0.63” 17 mm / 0.67” 12.5 mm / 0.49” 43.5 mm / 1.71” 13.5 mm / 0.53” 3.5 mm / 0.14” 6 mm / 0.23” 3 183.6 mm / 7.22” 80 mm / 3.14” 191 mm / 7.51” 121 mm / 4.76” 34 mm / 1,33” 183.6 mm / 7.22” 80 mm / 3.14” 191 mm / 7.51” 121 mm / 4.76

• ADVANCED MANUAL / bit Ten / 20 Procedure 1 To uninstall the bit Ten PC software you can use the link listed on the following menu: Start / All Programs / bit Ten / uninstall. Procedure 2 To uninstall the bit Ten PC software you can also follow the standard procedure: Start / Control Panel / Applications Installation / bit Ten / uninstall. 7.3 bit Ten SOFTWARE UN

• Audio bit Ten, ADVANCED MANUAL / bit Ten / 48 12. TECHNICAL SPECIFICATIONS POWER SUPPLY Voltage 11 ÷ 15 VDC Idling current 0.4 A Switched off without DRC 2.5 mA Switched off with DRC 4 mA Remote IN voltage 7 ÷ 15 VDC (1.3 mA) Remote OUT voltage 12 VDC (130 mA) SIGNAL STAGE Distortion - THD @ 1 kHz, 1V RMS Output 0.005 % Bandwith @ -3 dB 10 ÷ 22k Hz S/N Ratio @ A weighted Master Input 95 dBA AUX Input 96 dBA Channel Separation @ 1 kHz 85 dB Input sensivity (Speaker In) 2 ÷ 15 V RMS Input sensivity (AUX In) 0.6 ÷ 5 V RMS Input sensivity (PHONE) 2 ÷ 15 V RMS Input impedance (Speaker In) 2.2 kΩ Input

• Audio bit Ten, ADVANCED MANUAL / bit Ten / 16 6.3 AMPLIFIERS SENSITIVITY CALIBRATION 6.4 HOW TO CALIBRATE THE PHONE AND AUX IN INPUT SENSITIVITIES Once the bit Teninputcalibrationorde-equalization(ifany)proceduresarecomplete,youcancalibrateamplifierssensitivity. •Settheamplifierscrossoverfiltersasdesiredandthenconnectthemtothespeakers.  •Connectthebit Ten PRE outputs (Front - Rear - Sub outputs) to the amplifiers inputs using high quality RCA cables.  •Set�

• ADVANCED MANUAL / bit Ten / 30 2. Save Setup: saves the entire bit Ten configuration in a file (e.g. “bitTenConfig.dip”) that you can load again to the bit Ten a second time through the Load Setup function. This feature is available both in TARGET and in OFF LINE modes. 3. FINALlZE to bit Ten: loads all the parameters selected while configuring the bit Ten into the internal

• Audio bit Ten, ADVANCED MANUAL / bit Ten / 21 8. bit Ten INSTALLATION GUIDE USING A PC. To configure the bit Ten inputs, outputs, equalizations and time delays, the processor must be connected to a PC after calibrating the input levels. At that point, you need to have in mind the system you want to realize, since from this moment if you want to change any of the settings, you will have to go through the guided procedure all over again. More specifically the guided procedure will ask for: - What kinds of specialization the main inputs channels use. The guided procedure changes according

• Audio bit Ten, ADVANCED MANUAL / bit Ten / 29 The following chapters detail the system adjustments and acoustic tuning features. WARNING: We recommend that you do not modify the settings of your bit Ten to explore its features. Take your time to get familiar with the possibilities this software offers. If you decide to leave the amplifiers connected to the bit Ten, remember to perform the adjustments keeping the general volume at a level that does not damage the speakers in your system. This window indicates whether the bit Ten

• Audio bit Ten, ADVANCED MANUAL / bit Ten / 10 1. SPEAKERS IN HI-LEVEL STEREO FRONT+REAR (see 8.1) * To disable the Speaker Turn on function on the Front Left channel, move the indicated switch to the left to “OFF” position. 2. SPEAKERS IN HI-LEVEL MULTICHANNEL (see 8.2) 5.3 PERSONAL COMPUTER AND DIGITAL REMOTE CONTROL (DRC) 5.4 HIGH-LEVEL INPUT SIGNALS (optional) 5 USB cable (provided) FRONT REAR AMPLIFIED RADIO DECK OEM - ORIGINAL AMPLIFIER SOURCE FRONT HI MAX: 4 AMPLIFIED CHANNELS FRONT LOW OK NO DRC/ACLink cable (provied) * *

• ADVANCED MANUAL / bit Ten / 35 This setting automatically calculates the time speaker sound takes to get to the listener’s ear (Fig.1). Preliminary Remarks Sound moves through the air at a speed of 343 mt/sec (1.125 ft/sec) at a temperature of 20°C (68°F). If you know the distance from the sound emission point, you can then calculate the time sound takes to get to the listener�

• ADVANCED MANUAL / bit Ten / 31 If you click on the Config tab, a drop-down menu appears listing the entries shown in the image on the right: 1. I/O Configuration Wizard: sets up the system and puts the bit Ten in the required conditions (see 8.1.5). 2. Working Mode - Standard Expert : the software can work in two modes, acting on the crossover filter.  •Standa

• Audio bit Ten, ADVANCED MANUAL / bit Ten / 24 9. How to calibrate the bit Ten IN Level inputs. This procedure is delicate and requires particular attention. Improper execution can invalidate the final acoustic results. The bit Ten outputs must be disconnected from the amplifiers.  •Whileplayingtrack1oftheCD,turnthefirstknobtowardsthehighestsensitivity(position+).  •WhentheorangeLEDlightsuporflashes,stopturningandgobackslightlyuntiltheLEDturnsoff. •It

• Audio bit Ten, ADVANCED MANUAL / bit Ten / 34 5. Cut-off frequencies - Hi-P Hz 10 ÷ 20000: filter High-Pass - Lo-P Hz 10 ÷ 20000: filter Low-Pass If you select the Band-Pass filter, both Hi-P Hz and Lo-P Hz boxes will be available to set the band frequency. You can select the cut-off frequency by: - clicking on the corresponding drop-down menu, selecting the frequency range that includes the value to be set, and then the actual value; - clicking on the corresponding drop-down menu, selecting the frequency range and then moving from value to value with the arrow keys (up /

• Audio bit Ten, ADVANCED MANUAL / bit Ten / 40 9. TROUBLESHOOTING 1. bit Ten functioning problems - If, while tuning the system with a laptop PC, the bit Ten shows some problems functioning, try to disconnect the laptop PC power supply cable. This way, with the laptop PC working on battery power, you avoid a possible voltage difference in USB ground between car ground (bit Ten) and earth (PC). 2. The bit Ten does not connect to the PC software - If, while tuning the system with a laptop PC, the bit Ten is switched off and then on again, the connection is lost and the software can not “finalize” the selected setup. If you don’t want to lose the modifications and setup pr

• Audio bit Ten, ADVANCED MANUAL / bit Ten / 44 10. DRC - DIGITAL REMOTE CONTROL The DRC is the bit Ten remote control system. It is a microprocessor digital system that also controls and monitors the amplifiers equipped with the ACLink bus control, if present. When it is turned on the first time, the display will show the firmware version installed in the DRC. When the bit Ten is setup through the PC, the DRC can stay connected but its display will show the message “PC control - DRC is disabled”. The DRC features are: - bit Ten power on / off; - Main volume control; - Subwoofer volume control; - Front / Rear fader contro

• Audio bit Ten, ADVANCED MANUAL / bit Ten / 42 7. Before starting the bit Ten update, the software will present the following warnings: - do not disconnect the bit Ten from the PC; - do not disconnect the bit Ten from power supply; - temporarily disable the PC stand-by and energy saving features; - temporarily disable the PC screen saver; - close all running applications; - temporarily disable anti-virus and anti-spyware systems. 8. Once you have clicked OK, the Firmware update starts. The updating process will last from 30 seconds to 1

• Audio bit Ten, ADVANCED MANUAL / bit Ten / 37 The bit Ten software features a 31-band, ± 12 dB graphic equalizer for each system channel. In compliance with ISO requirements, frequencies are equally spaced at 1/3 Oct. from 20 to 20 kHz. The equalizer works according to the functioning mode chosen. So we have: - one equalizer for the Front. - one equalizer for the Rear. - one equalizer for the Subwoofer. Eg.: if examining the system described so far there would be: - one equalizer for the Front Mid-Tweeter. - one equalizer for the Front Woofer. - one equalizer for the Subwoofer.

• Audio bit Ten, ADVANCED MANUAL / bit Ten / 8 3. KEY MEM To turn the processor on and off when the vehicle ignition is turned on / off. Remark: This signal is memory-dependent: if the processor was turned off by a car sub-key connected to the KEY MEM, it will turn on again by turning the ignition key. If the processor was turned off by a different method (e.g. DRC) while the KEY MEM was still active, it will not turn on again through the KEY MEM and you will have to turn it on through either the DRC or REM IN. 4. MUTE IN: To mute the bit Ten outputs when starting the engine by connecting the terminal to the starter turn-on input or other devices. This control works by jumping

• Audio bit Ten, ADVANCED MANUAL / bit Ten / 26 18. Through a real-time progress bar and specific messages, the software shows how the procedure is being executed. Once the procedure is complete, you will see “Press Next to Continue”. Press BACK to go back to the previous step. Press NEXT to go ahead with the setup procedure. Press CANCEL to exit the procedure. 19. System configuration successfully completed. Stop playing the Test track, remove the supplied Setup CD from the CD player of your head unit and then click OK. Once the de-equalization is complete, the bit Ten DE-EQ CH

• Audio bit Ten, ADVANCED MANUAL / bit Ten / 25 13. Source equalization analysis. Sourcede-equalization(De-Eq)isonlyrequiredifthesourceisequalized. OEM sources (installed as standard by the car manufacturer) often have a high output  level(speakeroutput)withpresetequalizationthatcannotbedeleted.  Byreplacingthefactoryaudiosystem(speakersand/oramplifiers),thisequalization is harmful. The bit Tenhasanautomaticproceduretoverifyequalizationand,i

• Audio bit Ten, ADVANCED MANUAL / bit Ten / 33 The bit Ten has five crossover filters, one per each output channel. Each filter allows you to set the parameters of a single output channel. 1. Xover L/R Link: modifications applied to one of the channels (right or left) will also automatically be applied to the other one. To do so, click on the blue flashing light. Xover L/R Link affects all Filter Setting adjustments except Set Distance (Delay). 2. Invert Phase: inverts the phase of the channel under examination by 180°. This can be done by selecting the green light which will turn on. This can be useful t

• Audio bit Ten, ADVANCED MANUAL / bit Ten / 14 4. How to IN LEVEL calibrate the MASTER inputs. This procedure is delicate and requires particular attention. Improper execution can invalidate the final acoustic results. The bit Ten outputs must be disconnected from the amplifiers.  •Whileplayingtrack1oftheCD,turnthefirstknobtowardsthehighestsensitivity(position+).  •WhentheorangeLEDlightsuporflashes,stopturningandgobackslightlyuntiltheLEDturnsoff. 

• ADVANCED MANUAL / bit Ten / 32 This window is active. You can click the speakers or the speaker system to manage each single channel that, once selected, will be shown highlighted. If you keep the CTRL key pressed and click on another channel, this other channel will be selected and highlighted as well, similarly to what happens with the Channel Map (see 8.8). Listening point visual indicat

• Audio bit Ten, ADVANCED MANUAL / bit Ten / 11 5.5 LOW-LEVEL INPUT SIGNALS 5.6 CONNECTION WITH HANDS-FREE PHONE KIT PHONE +/- Input compatible with the hands-free kit speaker output (see 4.2.3). Sensitivity adjustable from 2 to 15 V RMS. PHONE MUTE: bit Ten ON. This gives priority to the phone conversation, allowing you to resume audio reproduction when the phone call is finished. PHONE MUTE: bit Ten OFF. This turns the bit Ten on. When a phone call is received, the ring tone is audible after around 5 seconds. Once the phone call is finished, the bit Ten

• Audio bit Ten, ADVANCED MANUAL / bit Ten / 19 1. Turn the bit Ten on. 2. Connect the USB cable to the appropriate port on the bit Ten and to an available USB slot on the PC. WARNING When connecting a PC laptop via USB cable to the bit Ten while the device is turned on, the laptop has to work with its own battery and stay disconnected from the mains adapter (external power supply). Once the connection between the PC laptop and the bit Ten is established, you can immediately connect the computer

• Audio bit Ten, ADVANCED MANUAL / bit Ten / 22 4. If synchronization is successful, a dialog box will show the data exchange between processor and software. Wait a few seconds and, finally, confirm by clicking the OK button. At this point you need to have in mind the system you want to realize beforehand, since from this moment if you want to change any of the settings you will have to go through the guided procedure all over again. More specifically the guided procedure will ask for: - Which auxiliary inputs will be used (e.g. AUX PHONE). - Which kind of signals will be allocated to the main inputs (e.g. Front Left or Front Right etc.). - Which speakers you are using for

• Audio bit Ten, ADVANCED MANUAL / bit Ten / 13 3. Turn on the device and play track 1 of the CD supplied with the bit Ten. • Setalltonecontrolstozero(flat). • Setbalanceandfadertocenter. • Adjusttheheadunitvolumetothemaximumundistortedoutputlevel. • Iftheheadunitprovidesanadjustableequalizer,makesurethatthecontrolsaresettozero(flat). WARNING: the head unit level must be elevated to the maximum undistorted level. If the head unit distortion level can not be tested in advance, bring the volume to approximately 80% of its maximum. If

• Audio bit Ten, ADVANCED MANUAL / bit Ten / 6 1. AUX IN L - R; auxiliary low-level stereo input. The bit Ten comes with an auxiliary stereo signal input to connect an external source, mp3 player, audio sources. Input sensitivity is adjustable from 0.6 to 5 V RMS. 2. INPUTS; RL - FL - FR - RR. Hi-level MASTER inputs (SPEAKERS). The bit Ten comes with 4 HI-LEVEL signal inputs to connect amplified signal cables coming from the main analog source. Input sensitivity is adjustable from 2 to 15 V RMS. Remark: If a low-level output source (PRE OUT)

Related Products and Documents (Car Stereo System):

Comparable Devices:

Similar Resources:

• Grundig Advance CC (39 pages) CarAudio Service ManualBtx * 32700 # • Materialnummer/Part Number 72010 760 4000Änderungen vorbehalten/Subject to alteration • Printed in GermanyE-BS 36 1099http://www.grundig.deAdvance CC(G.HK 0500)Zusätzlich erforderliche Unterlagen für den KomplettserviceAdditionally required Service Documents for the Complete ServiceServiceManualGrundig ServiceHot …

• Sony MEX-BT38UW - Bt Slot Usb 1wire (2 pages) MEX-BT38UWCD Receiver MP3/WMA/AAC Player Multi-format playback lets you play CDs, CD-Rs, or CD-RWs loaded with hundreds of MP3 or WMA songs .1 The 1-line 13 segment LCD display makes it easy to read song information and the front auxiliary input lets you connect almost any portable audio device to your car's sound system.The MEX-BT38UW features Bl …

• JVC CDA-5755 (32 pages) CASSETTE RECEIVER KS-FX621ENGLISHINSTRUCTIONS !"§”·π–π”GET0113-001A[U] !"#$ KS-FX621For installation and connections, refer to the separate manual. !"#$%&'()*+,-./0°√ÿ≥“¥Ÿ§ŸË¡◊Õ∑’Ë·¬°µË“ßÀ“° „π°“√µ‘¥µ—Èß·≈–°“√‡™◊ËÕ¡µËÕ«‘∑¬ÿ‡� …

• Sony XS-L1200B Marketing (1 pages) ø145(5Design and Specifications subject to change without notice.XS-L1200BSubwoofer2003 SONY MOBILE PRODUCT GUIDESpecificationsSpeaker Woofer 30 cm (12 in.), cone typePeak power 800 wattsRated power 200 wattsImpedance 4 ohmsSensitivity 89 dB/W/mFrequency response 22  2,500 HzMass Approx. 4.3 kg (9 lb. 8 oz.) per speakerSupplied accessory Parts …

• Sony DSX-MS60 (4 pages) The DSX-MS60 Marine Digital Media Receiver by Sony® features a USB5 1-wire Tune Tray that lets you protect, connect, charge and control your iPod®2 while boating. Make the most of your time on the water enjoying your music library with Sony audio technologies like DM+, Quick-BrowZer® and ZAPPIN™.DSX-MS60DSX-MS60 Marine Digital Media ReceiverBullets• …

• Sony XS-R4644 (1 pages) HOP Woofer ConeHighly Oriented Polyolen Woofer cone produces clear mid-bass frequencies.PEN mid-rangePEN mid-range for great linearity and smooth response with low distortion.Piezo Dome tweetersPiezo dome tweeters deliver clear highs.Ferrite / Neodymium magnetsHigh Energy Ferrite and Neodymium magnets provide controlled output at high volume levels.Power …

Comments, Questions and Opinions: