Siemens TC35 Operation & User’s Manual
|
34 Compatibility Compatibility withthe predecessor, the M20Terminal The direct predecessor of the TC35 Terminal is the M20 Terminal. The antenna connector is not compatible. The modified version (passive version) of the Votronic handset must be operated at the audio interface in accordance with HH-SI-30.3/V1.1/0. The following table shows the compatibility: Hardwar
Siemens TC35, 12 Interface description Purpose of the connectors/connections Use and operation The power supply is implemented by the +- and the GND wire. To switch the TC35 Terminal on, proceed as follows: – Either activate the DTR control line via the RS232 interface – Or connect IGT_IN to +. This connection has already been set up in the specified plug-in power supply unit below, see "Connectible plug-in power supply unit" on page14. Signal name PIN I/O Description Parameters + 1 I Positive supply voltage connection +8V...+30V max. 33V for 1min 2 Free PD_IN 3 I Reset input high active U IH >+5V (>3.5s) U IL <+2V IGT_IN
Siemens TC35, 13 Interface description Polarity reversal protection Polarity reversal protection is implemented by means of a power diode. The diode has a reverse voltage of 400V. Overvoltage protection Overvoltages are suppressed by a Zener diode after the polarity reversal protection diode. Fuses A permanently installed, non-replaceable fuse in the TC35 Terminal ensures electrical safety in the event of faults. Connect a fast 1.25A fuse to the supply line of the positive supply voltage for general protection of the Terminal, see "Safety and installation information" on page9.
Siemens TC35, 30 Operating states / LED Note: Usually, the network search takes only a fewseconds till the Terminal is registered. If the flashing continues, this means that no SIM card is inserted, no PIN number is entered or no GSM network is available. POWER DOWN Once the operating voltage is applied (+ and GND), the TC35 Terminal is in the POWER DOWN state. The operating voltage for the GSM module is disconnected (the switching regulator is off). In other words, the software of the GSM module is not active. A transition to the POWER DOWN state al
Siemens TC35, 21 Interface description The Bootbox BB35 enables software to be updated via the SIM interface. The Bootbox is connected instead of a SIM card (see "Bootbox BB35" on page33). Interference immunity Electrostatic discharge requirements in accordance with ETS 300-342-1 Antenna connector FME (male) A dual band antenna (GSM 900/1800) can beconnected to the RF interface. The connection is implemented as a 50 Ω FME (male) coaxial jack. Antenna connector Purpose of the connectors/connections Outer Inner Signal
Siemens TC35, 3 Contents Operating states / LED ........................ 29 POWER DOWN ............................... 30 Network search ............................... 31 Standby............................................ 31 Talk .................................................. 31 AT command control .......................... 32 SW update ........................................... 33 Compatibility ....................................... 34 Compatibility withthe predecessor, the M20Terminal ............................ 34 Certification / maintenance .........
Siemens TC35, 31 Operating states / LED Network search (no SIM card, no PIN number, no GSM network) In the network search state, the TC35 Terminal searches for a GSM network. All the components in the GSM Terminal (module) that are not required are shut down in several stages by the energy-saving software. This state is reached: • From the POWER DOWN state: by an active ignition (on) signal at the power supply connection or • From the TALK or STANDBY state: when the network is lost (out of range) Standby In the STANDBY state, the TC35 Terminal is ready to send and receive and registered in
Siemens TC35, 10 Installation Mounting kit for top-hat rail installation The TC35 Terminal can be attached to a 35mm top-hat rail using this mounting kit. There are two screws that are used tofix the top-hat rail adapter to the TC35 Terminal. The TC35 Terminal can be inserted onto the top-hat rail using this adapter.
Siemens TC35, 25 Interface description Interference immunity • The connecting cable must not exceed 1.8m in length. • Nominal signal range: ±15V • Max. load current 1A • Electrical fast transient burst requirements not specified • Surge immunity requirements not specified • Electrostatic discharge requirements in accordance with ETS 300-342-1 • Immunity RF common mode 0.15–80MHz in accordance with ETS300-342-1 Connectible RS232 connecting cable Item Order no. Supplier RS232 connecting cable 9-pin D-Sub extension 1:1 300574 Tecline Behrener Str. 8 D-66117 Saarbrücken Tel.:+49(0)6819267
8 Features Supplementary services • Phone book • Multiparty • DTMF (Dual Tone Multi Frequency) External interfaces • Connector for plug-in power supply unit • Handset audio interface • Mini-SIM card holder • Antenna connector FME (male) • RS232 interface (V.24/V.28 on the Sub-D socket) Accessories Antennae, SIM cards, power supply units, RS232 cab
Siemens TC35, 11 Interface description The following interfaces are available on the TC35Terminal: • Connector for the plug-in power supply unit • Handset connector • Mini-SIM card holder • Antenna connector FME (male) • RS232 interface (V.24/V.28 on the D-Sub socket) Plug-in power supply unit The TC35 Terminal receives its power supply in a wide voltage range (+8 V ... +30 V) via the power supply connectors. Two additional control lines are used for switching the Terminal on/off (resetting). The connection is implemented by a 6-pin Mini- Western connector. Connector for the plug-in power supply unit 3 2 1 4 5 6 1 + 2 free 3 PD_IN 4 IGT_IN 5 free 6
Siemens TC35, 6 Product description Highlights • Dual-band EGSM900 / GSM1800 • Data, voice, SMS and fax • R&TTE approval, GCF approval • Easy to integrate • Industrial interfaces • LED display • Wide input voltage range • Highly compact, light and powerful Applications • Fleet management • Teleservice • Security systems • Telematics • Telemetry • Remote monitoring • Remote meter reading • Vending machines
Siemens TC35, 7 Features Product data • Dual-band EGSM900 and GSM1800 • Certified in accordance with GSM phase2/2+ • Output performance: – Class 4 (2 W) for EGSM900 – Class 1 (1 W) for GSM1800 • Control via AT commands • Input voltage range +8V ... +30V • Dimensions: 65 x 74 x 33mm • Weight: approx. 130g Certification • R&TTE approval • GCF approval Audio • Half rate (HR) • Full rate (FR) • Enhanced full rate (EFR) SMS • Point-to-point MT and MO • SMS cell broadcast • Text and PDU mode Data • CSD up to 14.4kbps • USSD • Non-transparent mode • V.110, V.32 Fax • Group 3, classe
Siemens TC35, 36 Index A Accessories 8 Antenna connector 4, 11, 21 AT command control 32 Audio 7 B Bootbox 33 C Certification 7, 35 Compatibility 34 D Data 7 E External interface 8 F Fax 7 Features 7 Fuses 13 H Handset connector 4, 11, 15 I Installation 9 Interface description 11 L LED 4, 29 M Maintenance 35 Mini-SIM card holder 4, 11 N Network search 31 O Operating state 29 Overview 4 Overvoltage 13 P Package contents / scope of delivery 9 Plug-in power supply unit 4, 11 Polarity reversal 13 Power down 30 Product data 7 Product description 5 R RS232 interface 11, 23 S Safety and installation information 9 Sa
Siemens TC35, 32 AT command control The TC35 Terminal is controlled and programmed by means of AT commands. The AT command structure corresponds to the TC35 module used. The AT commands can be obtained from the ICM WM home page: www.siemens.com/wm.
Siemens TC35, 2 Contents Safety information ................................ 1 Contents ................................................. 2 Overview ................................................ 4 Front view.......................................... 4 Rear view ........................................... 4 Product description............................... 5 Highlights ........................................... 6 Applications ....................................... 6 Features.................................................. 7 Product data....................................... 7 Certification........................
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Harbor Freight Tools | 90980 | Assembly & operating instructions | harbor-freight-tools/90980-1HO.pdf | 27 May 2023 | 5 | 2.12 Mb |
2 | Pfaff | select 1520 | Instruction manual | pfaff/select-1520-4ZN.pdf | 06 Oct 2023 | 82 | 1.68 Mb |
3 | Husqvarna | Platinum 730 | Operation & user’s manual | husqvarna/platinum-730-E86.pdf | 24 Apr 2023 | 38 | |
4 | SEVERIN | RETRACTABLE STYLER 0436 | Dimensions | severin/retractable-styler-0436-4D8.pdf | 31 Jan 2023 | 1 | 0.68 Mb |
5 | Miele | HG05 | Operating instructions manual | miele/hg05-4HJ.pdf | 23 Nov 2022 | 84 | |
6 | Sony | NW-HD3 | Operating instructions manual | sony/nw-hd3-9M5.pdf | 11 Jun 2023 | 458 | 11.9 Mb |
Liquid Controls
Set-up and Connection GuideAn IDEX Energy & Fuels BusinessLC_IOM_ONTHEGOWIFIADAPTER V1: 05/17L I Q UID C O N T R O L SLC-ON THE GOTM Wireless WiFi AdapterP/N 81538
…
81538(12 pages) |
Maestro
MAESTRO 100EVO SERIESQUICK START GUIDE & USER MANUAL REV. 0.8WWW.MAESTRO-WIRELESS.COMEMAIL: [email protected]: 852 2869 0688FAX: 852 2525 4701ADDRESS: ROOM 3603-3609, 36/F, 118 CONNAUGHT ROAD WEST, SHEUNG WAN, HONG KONG
…
100EVO SERIES(32 pages) |
Edimax
USB ADSL ModemUSB ADSL ModemUSB ADSL Modem USB ADSL Modem Provides Panda Platinum for system anti virusProvides Panda Platinum for system anti virusAR-7025UmADescriptionsAR-7025UmA USB-ADSL Modem is an external ADSL modem connecting broadband ADSL line to USB connector of PC system.AR-7025UmA uses advanced ADSL chipset solution with complete set of industry …
AR-7025Um(2 pages) |
Sierra Wireless
AirCard® USB 306/307 MODEMAirCard® USB 308/309 MODEMAirCard® 310U MODEMwww.sierrawireless.comQUICK START GUIDEGUIDE DE DÉMARRAGE RAPIDEGUÍA DE INICIO RÁPIDO
…
306(24 pages) |
NETGEAR
Quick StartHigh Speed Cable ModemModel CM400Package ContentsCable modemEthernet cable Power adapterCoaxial cable(not included)Power adapterCable modemEthernet cableAttachable feet4. Connect the power adapter.Connect the power adapter to the cable modem and plug the power adapter into an electrical outlet.When the startup procedure is completed, the Power LE …
CM400(2 pages) |
TC Communications
Notice!Although every effort has been made to insure that this manual is currentand accurate as of date of publication, no guarantee is given or impliedthat this document is error free or accurate with regard to any specifica-tion. TC Communications, Inc. reserves the right to change or modifythe contents of this manual at any time without prior notificatio …
TC1631R(22 pages) |
Lennox Hearth Products Indoor Fireplace LMBV-42RMNPDF User Manual (@419HH9), Lennox Hearth Products LMBV-42RMN Indoor Fireplace (18/08/2023) LMBV-42RMN, 26 |
Aiphone Intercom System GF SystemAiphone GF System Intercom System Installation & maintenance GF System, 32 |
AEG Drill PM10EDrill #4Y77V8 PM10E, 39 |
Britton Stroller ShopperBritton Shopper User Manual (Doc Type: Stroller Instruction manual) Shopper, 44 |
Hamamatsu Photonics Security Camera C9100-02Security Camera #BM5S16 C9100-02, 30 |
Audison Processor bit Ten DProcessor #582KHB bit Ten D, 50 |
Thermaltake Desktop GTS VO3000 SeriesThermaltake GTS VO3000 Series User Guide (Doc Type: Desktop Operation & user’s manual) GTS VO3000 Series, 18 |
I-Tech Digital Signage SG SERIESI-Tech Digital Signage SG SERIES Operation & user’s manual SG SERIES, 30 |
Miller Welding System Summit Arc 1000Miller Summit Arc 1000 Welding System Owner's manual Summit Arc 1000, 48 |
LG Cell Phone 441G441G Operation & user’s manual - 696Y6A 441G, 186 |
Perel Saw PCS18501#T9HO75: PCS18501 Saw Operation & user’s manual PCS18501, 26 |