arf AVENSIS Instruction Manual Book

Text of arf AVENSIS User Guide:

• arf AVENSIS, 9 AVENSIS - Item code: BH137. Instruction Manual Installing the flap linkages as pictures below. Flap control horn 2x10mm. Secure. Flap A+B Epoxy PLUS glue 2.INSTALLING THE FLAP CONTROL HORN. Flap control horn. 3. INSTALLING THE FLAP LINKAGES. 3.INSTALLING THE FLAP LINKAGES. 100mm Repeat the procedure for the other wing half. Snap keeper.

• arf AVENSIS, 3 AVENSIS - Item code: BH137. Instruction Manual Caution: this model is not a toy! If you are a beginner to this type of powered model, please ask an experienced model flyer for help and support. If you attempt to operate the model without knowing what you are doing you could easily injure yourself or somebody else. Please keep your safety and well-being in mind at all times. Important: before you start construction Even if you have already built a large number of RC models please read right through these instructions and check all the kit components against the parts list

• arf AVENSIS, 5 AVENSIS - Item code: BH137. Instruction Manual 1) Install the rubber grommets and brass eyelets onto the aileron servos. I. AILERON. 1.INSTALLING THE AILERON SERVOS. Top side. Temporary pin to keep hinge centered. Assemble then apply drops of thin C/A to center of hinge,on both sides. Cut the covering away from the slot. Bottom side Flap Aileron Remove covering Servo tray.  2) Using a modeling knife, remove the cov- ering at possition show below. Secure

• arf AVENSIS, 12 AVENSIS - Item code: BH137. Instruction Manual INSTALLING THE ENGINE. Locate the long piece of wire used for the throttle pushrod. One end of the wire has been pre-bend in to a “Z” bend at the factory. This “Z” bend should be inserted into the throttle arm of the engine when the engine is fitted onto the engine mount. Fit the engine to the engine mount using the screws provided. Install the nose gear and secure it. Secure 120mm Mark point Drill a hole 3.5mmdiameter.

• arf AVENSIS, 17 AVENSIS - Item code: BH137. Instruction Manual secure.  1. Install one adjustable metal connector through the third hole out from the center of one servo arm, enlarge the hole in the servo arm using a 2mm drill bit to accommodate the servo connector. Remove the excess mate- rial from the arm. After installing the adjustable metal con- nector apply a small drop of thin C/A to the bottom nut. This will prevent the con- nector from loosening during flight. INSTALLING THE THROTTLE SERVO. Secure PARTS REQUIRE

• arf AVENSIS, 16 AVENSIS - Item code: BH137. Instruction Manual 3 x 12mm Install the spinner backplate, propeller and spinner cone. The spinner cone is held in place using two 3mm x 12mm wood screws. INSTALLING THE SPINNER. Left side. Secure. Drill a hole 2.5mm diameter Right side. Machine screw. Secure. 3x 12mm Front view.

• arf AVENSIS, 14 AVENSIS - Item code: BH137. Instruction Manual  6. When satisfied with the alignment of the stopper assembly tighten the 3mm x 20mm machine screw until the rubber stopper ex- pands and seals the tank opening. Do not over tighten the assembly as this could cause the tank to split.  7. Using a modeling knife, cut 3 lengths of fuel line 150mm long. Connect 2 lines to the 2 vent tubes and 1 line to the fuel pickup tube in the stopper.  8. Feed three lines through the fuel tank compartment and through the pre-drilled hole in the firewall.

• arf AVENSIS, 18 AVENSIS - Item code: BH137. Instruction Manual  2) Using the hardware provided, mount the main landing gear to the fuselage. Secure.  1) Assemble and mounting the wheel pants as shown in the following pictures. 5x35mm.

• arf AVENSIS, Instruction Manual book SPECIFICATION Made in Vietnam.    Wingspan : 1,700mm. 66.93 in.    Length : 1,400 mm. 55.12 in.    Weight : 3,3 kg. 7.26lbs Parts listing required (not included)    Engine : 55 -61 2stroke 72 4 stroke 10cc gas   Motor side : Power 46 Recommended Motor Battery : 14.8V 4S 4.000mAh LIPO    Radio : 05 channels.    Servo :

• arf AVENSIS, 30 AVENSIS - Item code: BH137. Instruction Manual *If possible, first attempt to balance the model by changing the position of the receiver bat- tery and receiver. If you are unable to obtain good balance by doing so, then it will be nec- essary to add weight to the nose or tail to achieve the proper balance point.  With the wing attached to the fuselage, all parts of the model installed ( ready to fly), and empty fuel tanks, hold the model at the marked balance point with the stabilizer level. Lift the model. If the

• arf AVENSIS, 7 AVENSIS - Item code: BH137. Instruction Manual Aileron control horn. 3.INSTALLING THE AILERON LINKAGES.  1. Working with the aileron linkage for now, thread one clevis onto one of the threaded wires.  2. Attach the clevis to the outer hole in the control horn. Install a silicone tube on the clevis. Attach the clevis to the outer hole in the con- trol horn.  3. Plug the aileron servo into the receiver and center the servo. Install the servo arm onto the servo. The servo arm should be perpen- dicular to the servo and point toward the mid- dle of the wing.  4. Locate one nylon servo arm, and usin

• arf AVENSIS, 24 AVENSIS - Item code: BH137. Instruction Manual  1) Using a modeling knife, remove the covering from the top of the fuselage and the covering from over the precut hinge slot cut into the lower rear portion of the fuselage This slot accepts the lower vertical.  2. Slide the rudder into the fuselage as same as picture below.  3. Mark the shape of the vertical on the left and right side on the rudder using a felt-tip pen.  4. Now, remove the rudder and using a modeling knife, carefully cut just inside the marked lines and remove the film of the rud- der. Just as you did with the horizontal stabi

• arf AVENSIS, 13 AVENSIS - Item code: BH137. Instruction Manual 3x20mm INSTALLING THE STOPPER ASSEMBLY  1. The stopper has been pre-assembled at the factory.  2. Using a modeling knife, cut one length of silicon fuel line (the length of silicon fuel line is calculated by how the weighted clunk should rest about 8mm away from the rear of the tank and move freely inside the tank). Connect one end of the line to the weighted clunk and the other end to the nylon pick up tube in the stop- per.  3. Carefully bend the second nylon tube up at a 45 de

• arf AVENSIS, 4 AVENSIS - Item code: BH137. Instruction Manual REPLACEMENT LARGE PARTS B. Wing panel. C. Fuselage. A. Cowling. D . Horizontal stabilizer. F. Aluminium wing dihedral brace. REPLACEMENT SMALL PARTS 2. Wheels 5. Plastic - enginemount. 6. Spinner. 8. Fuel Tank. 7.Tie wrap 4. Nose gear 3.Steering arm. 1. Aluminium landing gear. E. Vertical stabilizer

• arf AVENSIS, 29 AVENSIS - Item code: BH137. Instruction Manual  3.Insert two wing panels as pictures be- low. Left side. Secure. Secure. See picture wing attach to fuselage. Installing the fuselage hatch as same as pic- ture below. Top side Top side.

• 2 AVENSIS - Item code: BH137. Instruction Manual This instruction manual is designed to help you build a great flying aeroplane. Please read this manual thoroughly before starting assembly of your AVENSIS. Use the parts listing below to identify all parts. WARNING. Please be aware that this aeroplane is not a toy and if

• arf AVENSIS, 10 AVENSIS - Item code: BH137. Instruction Manual Bottom side. INSTALLING ENGINE MOUNT. Repeat the procedure for the other wing half. Drill a hole 4mm diameter. bend cut See pictures below: 3x20mm. 4x25mm Front view.

• arf AVENSIS, 15 AVENSIS - Item code: BH137. Instruction Manual  1. Slide the fiberglass cowl over the en- gine and line up the back edge of the cowl with the marks you made on the fuselage. COWLING.  2. While keeping the back edge of the cowl flush with the marks, align the front of the cowl with the crankshaft of the engine. The front of the cowl should be positioned so the crankshaft is in nearly the middle of the cowl opening. Hold the cowl firmly in place using pieces of masking tape.  3. Slide the cowl back over the engine and secure it in place using four wood screws. See picture

• 20 AVENSIS - Item code: BH137. Instruction Manual  1. Using a modeling knife, cut away the covering from the fuselage for the stabilizer and remove it.  2. Draw a center line onto the horizontal stabilizer. Then slide the horizontal into the fuselage.  3. Mark the shape of the vertical on the left and right

• 6 AVENSIS - Item code: BH137. Instruction Manual  4) Drill 1,6mm pilot holes through the block of wood for each of the four mounting screws provided with the servo.  5. Instal servo tray with aileron servo into the wing as same as picture below. 2.INSTALLING THE AILERON CONTROL HORN. Aileron control horn  3) Us

• arf AVENSIS, 27 AVENSIS - Item code: BH137. Instruction Manual Cut. Secure.    1. Cut out the switch hole using a modeling knife. Use a 2mm drill bit and drill out the two mounting holes through the fuselage side.     2. Secure the switch in place using the two machine screws provided with the radio system. INSTALLING THE SWITCH. Switch Switch Rudder pushrod Cut.

• arf AVENSIS, 8 AVENSIS - Item code: BH137. Instruction Manual Aileron II. FLAP. 1.INSTALLING THE FLAP SERVOS. Flap Servo tray Flap Repeat the procedure for the other wing half. Electric wire thread

• arf AVENSIS, 22 AVENSIS - Item code: BH137. Instruction Manual  Elevator pushrod install as same as the way of aileron pushrod. ELEVATOR PUSHROD INSTALLATION. Elevator control horn M2 M2 lock nut. Bend. Cut. Cut. A+B Epoxy PLUS glue Bottom side Elevator pushrod

• 26 AVENSIS - Item code: BH137. Instruction Manual  Rudder pushrod install as same as the way of aileron pushrod. RUDDER PUSHROD INSTALLATION. Rudder control horn. M2 M2 lock nut. Rudder pushrod Top side. bend. A+B Epoxy PLUS glue.

• arf AVENSIS, 28 AVENSIS - Item code: BH137. Instruction Manual    3. Position the battery pack and receiver behind the fuel tank. Use sing to two tie wraps to hold the battery and receiver securely in place as picture below. Do not permanently secure the receiver and battery until after balancing the model.    4. Using a 2mm drill bit, drill a hole through the side of the fuselage, near the receiver, for the antenna to exit. Tie wrap. 1.Locate

• arf AVENSIS, 11 AVENSIS - Item code: BH137. Instruction Manual NOSE GEAR INSTALLATION. Installing steering arm as follow Steering arm. Attach the pushrod wire to the steering arm. Bottom side.

Related Products and Documents (Toy):

Comparable Devices:

Similar Resources:

• Eduard Bismarck Part 2 (9 pages) detail set for 1/350 TRUMPETER kitsada detailů pro stavebnici 1/350 TRUMPETERREMOVEODSTRANITOPTIONVOLBAREPLACENAHRADITBENDOHNOUTGRINDOBROUSITSYMETRICAL ASSEMBLYSYMETRICKÁ MONTÁŽDRILL HOLEVRTAT OTVORAPPLY EXPRESS MASK AND PAINT BEFORE GLUINGPOUŽÍT EXPRESS MASK NABARVIT PRED SLEPENÍMCOLORED ETCHED PARTSLEPTANÉ BAREVNÉ DÍLYETCHED PARTSLEPTANÉ NEBAREV …

• DICKIE TOYS RC TURBO RACER SIDESWIPE (16 pages) D: Bedienungsanleitung GB: Operating instructions F: Mode d’emploiNL: Bedieningshandleiding I: Istruzioni per l’uso E: Instrucciones de usoP: Instruções de utilização S: Bruksanvisning N: BruksanvisningDK: Betjeningsvejledning FIN: Käyttöohje TR: Kullanım TalimatnamesiGR: Όδηγίες λειτουργίας BG: Инструкция …

• REVELL Austrian Airbus A340 Wiener Philharmoniker (14 pages) AUSTRIAN AIRBUS A 340WIENER PHILHARMONIKERA 04209-0389 2007 BY REVELL GmbH & CO. KG PRINTED IN GERMANYAUSTRIAN AIRBUS A 340 WIENER PHILHARMONIKER AUSTRIAN AIRBUS A 340 WIENER PHILHARMONIKERAm 10. Januar 2006 setzte Austrian Airlines mit einem eindrucksvollenSonderdesign eines kompletten Langstrecken-Jets wieder einmalbesondere Akzente.Die öst …

• Mattel M8416 (2 pages) BATTERY REPLACEMENTFor longer life use only alkaline batteries. Requires 3 AA alkaline batteries. Toy uses 3 replaceable AA (LR6) alkaline batteries. Replace batteries when sounds become garbled or faint. To replace batteries, use a Phillips head screwdriver (not included) to open battery door. Remove and set aside. Insert 3 replaceable AA or LR6 alkaline ba …

• Faller Central post office (12 pages) Vor Beginn des Bastelns sollten Sie sich mit den Spritzlingen und der Anleitung vertraut machen.Sollte es einmal vorkommen, daß ein Teil im Bausatz fehlt, kreuzen Sie bitte das fehlende Teil inder Anleitung an und schicken Sie diese bitte an Fa. Gebr. FALLER GmbH, Abt. Kundendienst,Kreuzstraße 9, 78148 Gütenbach. Sie erhalten dann umgehend Ersatz.In diese …

• Eduard F/A-18E interior (4 pages) detail set for 1/32 REVELL kit • sada detailů pro stavebnici 1/32 REVELL1/432948REMOVEODSTRANITOPTIONVOLBAREPLACENAHRADITBENDOHNOUTGRINDOBROUSITSYMETRICAL ASSEMBLYSYMETRICKÁ MONTÁŽDRILL HOLEVRTAT OTVORAPPLY EXPRESS MASK AND PAINT BEFORE GLUINGPOUŽÍT EXPRESS MASK NABARVIT PRED SLEPENÍMCOLORED ETCHED PARTSLEPTANÉ BAREVNÉ DÍLYETCHED PARTSLEPTANÉ NE …

Comments, Questions and Opinions: