Akasa Freedom Force VC05 Installation Manual
|
Akasa Freedom Force VC05, 1 2 Warning Improper Installation will result in damage to the VGA card. Never switch on the computer system until the fan is connected. Electrostatic discharge (ESD) can damage system components. Use an ESD controlled workstation. If such a workstation is not available, wear an antistatic wrist strap or touch an earthed surface before handling any PC components. If the VGA card and its components interfere with the installation of this product, stop the installation. Refer to the akasa website for the full list of akasa VGA coolers and their latest compatibility list. i
Akasa Freedom Force VC05, 3 4 COMPATIBILIY LIST INSTALLATION PROCEDURE VGA card preparation 1. Unplug the stock cooler fan connector. 2. Undo all screws or pins securing the original cooler and remove from the card. 3. Clean the surface of RAM and GPU chips. Note: Use Isopropyl or Akasa Timclean to remove thermal grease residue. Freedom Force cooler installation 1. Attach the aluminium heatsinks (part A) to each RAM chip (on the GPU side of the VGA card) by removing protective liner from the heatsinks and gently pressing it down once located correctly o
5 6 a b 3. Note: The cooler’s mounting is pre-set to Type B (see Product Compatibility). If your VGA card has Type A or C mounting follow the next step otherwise proceed to step 4. To adjust the mounting dimensions unscrew the metal clips from the base (a), pull the four standoffs (Part D) out or the rubber seals (Part F) and place them in the required holes
Akasa Freedom Force VC05, 8 7. Once the card with the new cooler is installed in the motherboard slot connect the 3-pin fan connector to the motherboard fan header or directly to the PSU using the adapter (part G). Note: If you connect the VGA cooler directly to the motherboard, ensure any smart/auto fan control for the connector used has been disabled in BIOS (if applicable). 7 AVERTISSEMENT Une mauvaise installation endommagera la carte VGA. N’allumez jamais votre ordinateur tant que le ventilateur n’est pas connecté. Des décharges électrostatiques (ESD) peuvent endommager les composants du système. Utilisez une station de travail protégée contre les décharges électro
Akasa Freedom Force VC05, 9 10 LISTE DE COMPATIBILITÉ COMPATIBILITÉ DU PRODUIT Le refroidisseur Freedom Force est compatible avec trois types de dimensions de montage: Type A 61.5mm entre les centres des trous de montage Type B 53.2mm entre les centres des trous de montage Type C 43.2mm entre les centres des trous de montage Emplacement du trou de montage ATI NVIDIA 61.5 x 61.5 Geforce GTX 285 Geforce GTX 280 Geforce GTX 260 53.2 x 53.2 Radeon HD 4870 Radeon HD 4850 Radeon HD 4830 Radeon HD 3870 Radeon HD 3850 Radeon 2900 XT Radeon 2900 Pro Radeon X1950 XTX Radeon X1950 Pro Radeon X190
Akasa Freedom Force VC05, 11 12 a b 3. Remarque: Le montage du refroidisseur est prédéfini sur le type B (voir la Compatibilité du produit). Si le type de montage de votre carte VGA est un montage de type A ou C, continuez l’étape suivante sinon allez à l’étape 4. Pour ajuster les dimensions de montage, dévissez les attaches en métal de la base (a), retirez les quatre chevilles (composant D) ou les joints en caoutchouc (composant F) et placez-les dans les trous requis (b). Fixez les chevilles avec les anneaux en caoutchouc et attachez de nouveau les plaques en métal. 4. Positionnez le refroidisseur sur la carte VGA, en alignant les chevilles avec les quatr
Akasa Freedom Force VC05, 13 14 5. Tout en supportant le refroidisseur d’une main, faites pivoter doucement la VGA. Identifiez les quatre chevilles du refroidisseur d’Akasa et placez les rondelles d'isolation en plastique (composant B) sur chacune des quatre vis. 6. Fixez le refroidisseur à l’aide des écrous à embase (composant E), un pour chaque vis, en serrant les écrous progressivement de manière diagonale. Remarque: Ne serrez pas trop fort les vis car cela risque d’endommager la carte VGA. Certaines cartes VGA ont des puces mémoire sur les deux côtés de la c
Akasa Freedom Force VC05, 15 16 WARNUNG Eine nicht sachgerechte Installation führt zu einer Beschädigung der VGA card. Schalten Sie das Computer System nicht ein, bevor der Lüfter angeschlossen wurde. Die Systemkomponenten können durch elektrostatische Entladung beschädigt werden. Benutzen Sie einen for ESD schützenden Arbeitsplatz. Sollte ein solcher Arbeitspaltz nicht verfügbar sein, tragen Sie ein antistatisches Armband or berühren Sie eine geerdete Oberfläche vor dem hantieren mit PC Komponenten. Wenn bei der Installation dieses Produkts d
Akasa Freedom Force VC05, 17 18 KOMPATIBILITÄTSLISTE INSTALLATION Vorbereiten der VGA-Karte 1. Trennen Sie den Lüfteranschluss des original Kühlers. 2. Lösen Sie alle Schrauben oder Stifte, mit denen der ursprüngliche Kühler befestigt ist und entfernen Sie ihn von der Karte. 3. Reinigen Sie die Oberfläche des RAM- und GPU-Chips. Hinweis: Reste des Thermalfetts können Sie mit Isopropyl-Alkohol oder Akasa Timclean entfernen. Installation des Freedom Force-Kühlers 1. Befestigen Sie die Aluminium-Heatsinks (Teil A) auf allen RAM-Chips (an der GPU-Seite der VGA-Karte), indem Sie die
Akasa Freedom Force VC05, 19 20 a b 3. Hinweis: Die Montage des Kühlers ist auf Typ B eingestellt (siehe Produktkompatibilität). Wenn Sie eine VGA-Karte mit den Montagetypen A oder C haben, führen Sie den nächsten Schritt aus. Anderenfalls können Sie bei Schritt 4 fortfahren. Um die Montagemaße anzugleichen, lösen Sie die Metallklammern von der Basis (a), ziehen Sie die vier Abstandsbolzen (Teil D) aus den Gummidichtungen (Teil F) heraus, und setzen Sie sie in die erforderlichen Löcher ein (
Akasa Freedom Force VC05, 22 7. Sobald die Karte mit dem neuen Kühler im Motherboard-Steckplatz installiert ist, schließen Sie den 3-poligen Lüfteranschluss an den Motherboard-Lüfterheader oder mit dem Adapter (Teil G) direkt an die PSU an. Hinweis: Wenn Sie den VGA-Lüfter direkt an das Motherboard anschließen, stellen Sie sicher, dass im BIOS alle Einstellungen für eine intelligente (Smart) oder automatische (Auto) Lüftersteuerung deaktiviert ist (wenn zutreffend). 21 Aviso Instalação imprópria resultará em danos à placa VGA. Nunca ligue o computador até que o ventilador esteja conectado. D
Akasa Freedom Force VC05, 23 24 LISTA DE COMPATIBILIDADE COMPATIBILIDADE DO PRODUTO O Cooler Freedom Force é compatível com três tipos de montagem e dimensões: Tipo A 61.5 mm de distância entre os centros dos furos de montagem Tipo B 53.2 mm de distância entre os centros dos furos de montagem Tipo C 43.2 mm de distância entre os centros dos furos de montagem. Tipo de Furação ATI NVIDIA 61.5 x 61.5 Geforce GTX 285 Geforce GTX 280 Geforce GTX 260 53.2 x 53.2 Radeon HD 4870 Radeon HD 4850 Radeon HD 4830 Radeon HD 3
Akasa Freedom Force VC05, 25 26 a b 3. Nota: A montagem do cooler está pré-configurada para o Tipo B (veja a compatibilidade do produto). Caso sua placa VGA seja da montagem Tipo A ou C siga as próximas etapas, caso contrário siga a etapa 4. Para ajustar o tamanho na montagem, solte os clips de metal da base (a), puxe os quatro parafusos (Parte D) e as arruelas de borracha (Parte F) e coloque-os na furação correspondente (b). Fixe os parafusos com as arruelas de borracha e encaixe as placas de metal. 4. Posicione o cooler sobre a placa
Akasa Freedom Force VC05, 27 28 5. Enquanto segura o cooler com a sua mão, vire suavemente a VGA. Localize os quatro parafusos do cooler akasa e coloque as arruelas de plástico (parte B) sobre cada um dos quatro parafusos. 6. Fixe o cooler com as porcas (parte E), sendo uma para cada parafuso, aperte as porcas gradualmente de forma transversal. Nota: Não aperte demais os parafusos, isto pode danificar a placa VGA. Algumas placas VGA possuem chips de memória em ambos os lados da placa. Para resfriar os chips no verso ou reguladores de voltagem, utilize o dissipador de memória, akasa AK-VMC-01BK. 1 4 2 3 7. Com a placa de vídeo e o novo cooler instalados no slot da pla
Akasa Freedom Force VC05, 29 30 AVISO Una instalación inadecuada puede dañar la tarjeta VGA. Nunca encienda el ordenador hasta que el ventilador este conectado. Descargas Electrostáticas (ESD) pueden dañar los componentes de su sistema. Si una estación de trabajo con protección antiestática no esta a su disposición, use una pulsera antiestática o toque una superficie que haga tierra antes de manipular cualquier componente de su ordenador. Si la tarjeta VGA y sus componentes no le permiten instalar este producto de manera adecuada, interrumpa la instalación. Consulte con la página Web d
Akasa Freedom Force VC05, 31 32 LISTA DE COMPATIBILIDADES PROCEDIMIENTO DE INSTALACIÓN Preparación de la tarjeta VGA 1. Desconecte el conector del ventilador del disipador original que viene con la tarjeta grafica. 2. Afloje todos los tornillos o contactos de seguridad del disipador original y quítelos de la tarjeta. 3. Limpie la superficie de la memoria RAM y de los chips GPU. Nota: Utilice alcohol isopropílico o Akasa Timclean para quitar los residuos de grasa térmica. Instalación del disipador Freedom Force
Akasa Freedom Force VC05, 33 34 a b 3. Nota: El montaje del disipador está predefinido para el Tipo B (ver Compatibilidad de productos).Si su tarjeta VGA tiene un montaje Tipo A o C, siga el paso siguiente, de no ser así, vaya al paso 4. Para ajustar las dimensiones del montaje afloje los clips de metal de la base (a), saque los cuatro soportes (Parte D) de las juntas de goma (Parte F) y colóquelos en los agujeros requeridos (b). Fije los soportes con los anillos de goma y vuelva a colocar las placas de metal. 4. Coloque el
7. Una vez instalada la tarjeta con el nuevo disipador en la ranura de la placa madre, conecte el conector del ventilador de 3 pines en el cabezal del ventilador en la placa base o directamente a la fuente de alimentación usando el adaptador proporcionado (parte G). Nota: Si conecta el disipador VGA directamente a la placa base, asegúrese
AEG SANTO C 7 18 40-4I Freezer Operation & user’s manual
SANTO C 7 18 40-4I |
Samsung Refrigerator Freezer Operation & user’s manual
Refrigerator |
AEG Electrolux ERB 8643 Freezer Instruction book
ERB 8643 |
Amana BX521VE Freezer Owner's manual
BX521VE |
Delfield F13BC44 Freezer Specifications
F13BC44 |
Frigidaire FFU12C2CW Freezer Factory parts catalog
FFU12C2CW |
Zanussi ZCUF 41 Freezer Instruction book
ZCUF 41 |
Electrolux ER2342B Freezer Instruction booklet
ER2342B |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Craftsman | 358.745270 | Instruction manual | craftsman/358-745270-1LF.pdf | 21 Nov 2023 | 19 | 0.88 Mb |
2 | Daewoo | FR-143R-DS | Instruction manual | daewoo/fr-143r-ds-T6I.pdf | 03 Oct 2022 | 4 | 0.08 Mb |
3 | Philips | DC220 | Quick start manual | philips/dc220-Z9U.pdf | 21 Nov 2023 | 2 | 4.13 Mb |
4 | Honeywell | 7850LP-I1-5210E - Hand Held Products Dolphin 7850 | Operation & user’s manual | honeywell/7850lp-i1-5210e-hand-held-products-dolphin-7850-J8M.pdf | 09 Feb 2023 | 36 | 0.34 Mb |
5 | Hitachi | RAS-X10HAK | Installation manual | hitachi/ras-x10hak-HTG.pdf | 22 Oct 2023 | 2 | 0.93 Mb |
6 | Craftsman | 944.609040 | Owner's manual | craftsman/944-609040-621.pdf | 17 Mar 2023 | 52 | 2.22 Mb |
Frigidaire
PRODUCT NO. BASE MODEL NO. SERIES COLOR VOLTSFFU17F9GW3 FFU17F9G 134A white 115MARKETNorth AmericaPublication No.5995326922990824-EN/SERVICE /ECL365FREEZERModel No.FFU17F9G©1999 White Consolidated Industries, Inc.All rights reservedFACTORY PARTS CATALOGFREEZERWIRING DIAGRAM - # 216569300OWNER’S GUIDE - # 216657700SERVICE DATA SHEET - #216569300101 Masters …
FFU17F9G(7 pages) |
Crosley
Use & Care GuideManual de Uso y CuidadoCrosley Corporation916 Copperfield Blvd NE.Concord, NC 28025www.crosley.comUpright Freezer Congelador Vertical Models/Modelos: VFUD15TW, VFUD18TW,VFUD21TW
…
Conservator(34 pages) |
LINDR
LINDR FLOW-THROUGHCONTACT COOLINGNumber 009-2020 REV00 Valid 2020-03-09INSTRUCTION MANUALENGLISH KONTAKT 300/K TWIN POWER GREEN LINE KONTAKT 300 TWIN POWER GREEN LINE
…
KONTAKT 300/K(24 pages) |
Fisher & Paykel
Operating instructionsDetails many of the operating instructions and information regarding temperature control, sabbath mode, and refrigeratorsounds.635 mm wide E331T, E381T, E411T, E415H680 mm wide E440TModels:790 mm wide E521T, RF521TTemperature control• When the refrigerator is first turned on, the powerful cooling system will automatically cool both re …
E331T(4 pages) |
Felix Storch
Write the Serial Number here ______________________ Instruction Manual 7 Cubic Foot Chest Freezer Model CF07L BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS Felix Storch, Inc. Summit Appliance Division 770 Garrison Avenue Bronx, NY 10474 www.summitappliance.com
…
CF07L(12 pages) |
Tecnolec
FP)ULGJH-)UHH]HU 7&:8INSTRUCTION MANUALMODEL: 7&6/87&%.8
…
TC145W-U(15 pages) |
Ningbo Tractor Benye 40 Series#MKXH15 Benye 40 Series: Ningbo Tractor Owner Documentation Benye 40 Series, 61 |
Hitachi Grinder G 10SR2Handling instructions manual for Hitachi G 10SR2 Grinder G 10SR2, 41 |
Optiview DVR HDVR4/8/16-Q2#NB9E32 HDVR4/8/16-Q2: Optiview DVR Owner Documentation HDVR4/8/16-Q2, 342 |
Apple Laptop MacBook ProApple Product User Manual: MacBook Pro PDF Service source - 57NOSG MacBook Pro, 199 |
Lincoln Electric Welding System WELDMARK 225Lincoln Electric WELDMARK 225 Welding System Operator's manual WELDMARK 225, 36 |
S&S Northern Gas Detectors Merlin#7E4JE8: Merlin Gas Detectors Operation & user’s manual Merlin, 8 |
Haier TV K15PFCD2602TXTPDF Manual (@ZVAC6V), Haier K15PFCD2602TXT TV (Sunday 28-01-2024) K15PFCD2602TXT, 36 |
Browning Other BUCK MARK 22Manual for Browning BUCK MARK 22 Other BUCK MARK 22, 29 |
CHIEF Racks & Stands FHB3036User Guide: CHIEF FHB3036 (8GW4F7, Upd.18/11/2023) FHB3036, 4 |
System Sensor Smoke Alarm DH200RPLSystem Sensor DH200RPL Guide (Doc Type: Smoke Alarm Installation and maintenance instructions manual) DH200RPL, 8 |
Sony Stereo Receiver STR-K685Sony Product Manual: STR-K685 PDF Service manual - 94J237 STR-K685, 52 |
Electrolux Refrigerator RF 502Refrigerator #7HYCDQ RF 502, 24 |