Manualios.com

MasterCraft 8 U.S. GALLON (30.3 L) AIR COMPRESSOR Instruction Manual

  • 8 U.S. GALLON (30.3 L) AIR COMPRESSOR Air Compressor
  • maF2jNBEkzbaw
  • Instruction Manual
  • PDF / Adobe Acrobat Reader
  • 33

MasterCraft 8 U.S. GALLON (30.3 L) AIR COMPRESSOR Manual Online:

3.5, 1289 votes
MasterCraft 8 U.S. GALLON (30.3 L) AIR COMPRESSOR User Manual
MasterCraft 8 U.S. GALLON (30.3 L) AIR COMPRESSOR User Guide
MasterCraft 8 U.S. GALLON (30.3 L) AIR COMPRESSOR Online Manual

Text of MasterCraft 8 U.S. GALLON (30.3 L) AIR COMPRESSOR User Guide:

  • WARRANTY 29 8 U.S. GALLONS (30.3 L) AIR COMPRESSOR 058-9316-0 H. this warranty will not apply to normal deterioration of the exterior finish, such as, but not limited to, scratches, dents, paint chips, or to any corrosion or discolouring by heat, abrasive and chemical cleaners; I. this warranty will not apply to component parts sold by and identified as the product

  • MasterCraft 8 U.S. GALLON (30.3 L) AIR COMPRESSOR, SAFETY GUIDELINES 8 8 U.S. GALLONS (30.3 L) AIR COMPRESSOR 058-9316-0 Extension cords As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drip in voltage, resulting in loss of power and possible product damage. Refer to the table to determine the required minimum wire size. Recommended Minimum Wire Gauge for Extension Cords* (120 V) * Based on limiting the line voltage drop to five volts at 150% of the rated amperes. The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14-gauge cord ca

  • MasterCraft 8 U.S. GALLON (30.3 L) AIR COMPRESSOR, ASSEMBLY INSTRUCTIONS 13 8 U.S. GALLONS (30.3 L) AIR COMPRESSOR 058-9316-0 Assembly • Unpack the air compressor unit. Inspect the unit for damage. If the unit has been damaged, contact the retailer immediately. • Check the air compressor’s identification label to ensure that you have purchased the intended model and that it has the required pressure rating for its intended use. Packaging contents Description Qty. Illustration Air compressor 1 Owner’s manual 1 Air filter 1 Removable handle 1 Thumbscrews 1 Wheel kit 1

  • MasterCraft 8 U.S. GALLON (30.3 L) AIR COMPRESSOR, MAINTENANCE 23 8 U.S. GALLONS (30.3 L) AIR COMPRESSOR 058-9316-0 Clean the air filter A dirty air filter will reduce air compressor performance and life. To avoid contaminating the pump, the filter should be cleaned frequently and replaced on a regular basis. Clean the foam filter by immersing it in warm, soapy water. Dry thoroughly after. Test for leaks Check that all connections are tight. Small leaks in the tank, hoses, connections or transfer tubes will substantially reduce the air compressor and tool performance. Spray a small amou

  • MasterCraft 8 U.S. GALLON (30.3 L) AIR COMPRESSOR, OPERATING INSTRUCTIONS 17 8 U.S. GALLONS (30.3 L) AIR COMPRESSOR 058-9316-0 5. Set the pressure switch (1) to the ON position. The compressor will start. Run the compressor for 30 minutes. If it fails, turn it off immediately and call the toll- free helpline at: 1-800-689-9928. Please note that breaking-in the unit is only required prior to first use (fig I) . 6. After 30 minutes, turn off the pressure switch. 7. Close the tank drain valve (I) by turning it clockwise (fig J) . 8. Set the pressure switch to the ON position. The air receiver will fill to cut

  • ASSEMBLY INSTRUCTIONS 14 8 U.S. GALLONS (30.3 L) AIR COMPRESSOR 058-9316-0 Tools required for assembly (not included): Wheel kit Qty. Illustration Axle 2 Wheel 2 Washer 2 Lock washer 2 Nut 2 Accessory Qty. Illustration 11/16" open end wrench or 1 Adjustable wrench 1

  • OPERATING INSTRUCTIONS 18 8 U.S. GALLONS (30.3 L) AIR COMPRESSOR 058-9316-0 Start-up procedure 1. Set the pressure switch (1) to the OFF position (fig K) . 2. Turn the air pressure regualtor knob counter-clockwise until it stops. 3. Attach hose (1) and accessories (fig L) . WARNING! Potential hazard that could result in serious injury or loss of life. • Risk of bur

  • SAFETY GUIDELINES 7 8 U.S. GALLONS (30.3 L) AIR COMPRESSOR 058-9316-0 • The compressor must be located in a well-ventilated area for cooling, and must be a minimum of 12” (31 cm) away from the nearest wall. • Protect the air hose and the power cord from damage and puncture. Inspect them for weak or worn spots every week, and replace them if necessary.

  • MasterCraft 8 U.S. GALLON (30.3 L) AIR COMPRESSOR, TECHNICAL SPECIFICATIONS 3 AIR COMPRESSOR 8-GALLON (30.3 L) 058-9316-0 *CFM: Cubic feet per minute (The volumetric flow rate of a gas corrected to standardized conditions of temperature and pressure). RUNNING HORSEPOWER 1.5 HP TANK SIZE 8 U.S. gallons (30.3 L) AIR DELIVERY (CFM*) @ 40 PSI 4.8 AIR DELIVERY (CFM*) @ 90 PSI 3.5 CUT-IN PRESSURE 105 PSI CUT-OUT PRESSURE 135 PSI PUMP DESIGN Oil-less, direct-drive, single-stage MOTOR 3,400 RPM POWER 120 V, 60 Hz, 12 A WEIGHT 57 lb 3 oz (26 kg) POWER CORD SJT 16 AWG / 72" (1.83 m) EXTENSION CORD SJT 12 AWG / Maximum 30' (9.1 m)

  • MasterCraft 8 U.S. GALLON (30.3 L) AIR COMPRESSOR, OPERATING INSTRUCTIONS 19 8 U.S. GALLONS (30.3 L) AIR COMPRESSOR 058-9316-0 4. Close the tank drain valve (1). Plug in the power cord (2) (fig M) . 5. Set the pressure switch to the ON position and allow the tank pressure to build. Motor will stop when tank pressure reaches cut-out pressure. 6. Turn the air pressure regulator knob clockwise until desired pressure is reached. WARNING! Potential hazard that could result in serious injury or loss of life. • High temperatures are generated by the electric motor and the pump. To prevent burns or other injuries, DO NOT touch the air compressor while it is runni

  • MasterCraft 8 U.S. GALLON (30.3 L) AIR COMPRESSOR, IMPORTANT INFORMATION 12 8 U.S. GALLONS (30.3 L) AIR COMPRESSOR 058-9316-0 Tool Compatibility Chart Inflation/Recreation Air tool Operates Tool Continuously Operates Tool Intermittently Not Recommended Finishing Nailer (16-gauge) Framing Nailer Flooring Nailer Die Grinder Angle Grinder Air Ratchet Cut-off Tool DIY Paint Sprayer Brad Nailer (18-gauge) 3-in-1 Brad/Finishing/Stapler Roofing Nailer Impact Wrench Drill Hammer Chisel Shears Sander Polisher Grease/Caulking Gun Tool Compatibility Chart

  • MasterCraft 8 U.S. GALLON (30.3 L) AIR COMPRESSOR, TROUBLESHOOTING 25 8 U.S. GALLONS (30.3 L) AIR COMPRESSOR 058-9316-0 The regulator does not regulate the pressure. The regulator or its internal parts are dirty or damaged. Replace the regulator. The pressure is low or there is not enough air. 1. There is a leak at one of the fittings. 2. The tank drain valve is open. 3. The air intake is restricted. 4. Prolonged excessive use of air. 5. There is a hole in the air hose. 6. The tank leaks. 7. The valve is leaking. 1. Check the fittings with soapy water. Tighten or reseal leaking fittings (apply plumber’s tape on threads). Do not overtighten. 2. Close the dra

  • MasterCraft 8 U.S. GALLON (30.3 L) AIR COMPRESSOR, SAFETY GUIDELINES 4 8 U.S. GALLONS (30.3 L) AIR COMPRESSOR 058-9316-0 Safety guidelines This manual contains information that relates to PROTECTING PERSONAL SAFETY and PREVENTING EQUIPMENT PROBLEMS. It is very important to read this manual carefully and understand it thoroughly before using the product. The symbols listed below are used to indicate this information. Note : The word “Note” is used to inform the reader of something the user needs to know about the tool. SAFETY RECOMMENDATIONS These precautions are intended for the personal safety of the user and others work

  • MasterCraft 8 U.S. GALLON (30.3 L) AIR COMPRESSOR, ASSEMBLY INSTRUCTIONS 15 8 U.S. GALLONS (30.3 L) AIR COMPRESSOR 058-9316-0 Positioning of the air compressor 1. Position the air compressor (1) near an electrical outlet (2) (fig A) . 2. The compressor must be at least 12" (31 cm) from any wall (3) or obstruction, in a clean, well-ventilated area to ensure sufficient air flow and cooling (fig A). 3. Place the air compressor on the floor or a hard, level surface. The air compressor must be level to ensure proper drainage of the moisture in the tank. Wheel assembly 4. Insert the axle (1) through one of the wheels (fig B) . 5. Insert axle (1) through the bracket on the bottom of the tank assembly. Slide on washer (2), lock

  • MasterCraft 8 U.S. GALLON (30.3 L) AIR COMPRESSOR, 8 U.S. GALLON (30.3 L) AIR COMPRESSOR 058-9316-0 Quick Start Guide If any parts are missing or damaged, or if you have any questions, please call 1-800-689-9928. Read and understand this instruction manual thoroughly before using the product. It contains important information for your safety as well as operating and maintenance advice. Keep this instruction manual for future use. Should this product be passed on to a third party, then this instruction manual must be included.

  • MasterCraft 8 U.S. GALLON (30.3 L) AIR COMPRESSOR, IMPORTANT INFORMATION 11 8 U.S. GALLONS (30.3 L) AIR COMPRESSOR 058-9316-0 Pressure switch This switch turns the compressor on and off. It is operated manually and when it is in the ON position, it allows the motor to start if the pressure in the air tank is below the factory set cut-in pressure, and allows the motor to stop if the pressure in the air tank reaches the factory set cut-out pressure. Be sure to set this switch to the OFF position when the compressor is not being used and before unplugging the compressor. Safety valve This valve is used to prevent system failure by draining pressure from the s

  • MasterCraft 8 U.S. GALLON (30.3 L) AIR COMPRESSOR, MAINTENANCE 21 8 U.S. GALLONS (30.3 L) AIR COMPRESSOR 058-9316-0 General maintenance Draining the air tank Through normal operation of your air compressor, condensation water will accumulate in the tank. To prevent corrosion of the tank from the inside, condensation must be drained at the end of every workday. Note: Allow unit to cool before draining tank. Drain valve (I) becomes hot during operation. • Set the pressure switch to the OFF position. • Unplug the power cord. • Turn air pressure regulator knob counter-clockwise to set the outlet pressure to zero. • Pull and hold rin

  • MasterCraft 8 U.S. GALLON (30.3 L) AIR COMPRESSOR, TABLE OF CONTENTS 2 8 U.S. GALLONS (30.3 L) AIR COMPRESSOR 058-9316-0 QUICK START GUIDE TECHNICAL SPECIFICATIONS 3 SAFETY GUIDELINES 4–8 KEY PARTS DIAGRAM 9 IMPORTANT INFORMATION 10–12 ASSEMBLY INSTRUCTIONS 13–15 OPERATING INSTRUCTIONS 16–20 MAINTENANCE 21–23 TROUBLESHOOTING 24–25 EXPLODED VIEW 26 PARTS LIST 27 WARRANTY 28–29

  • MasterCraft 8 U.S. GALLON (30.3 L) AIR COMPRESSOR, TROUBLESHOOTING 24 8 U.S. GALLONS (30.3 L) AIR COMPRESSOR 058-9316-0 PROBLEM POSSIBLE CAUSES SOLUTIONS The motor will not run or start. 1. The power cord is not plugged in. 2. The pressure switch is in the OFF position. 3. The extension cord is the wrong wire gauge or is too long. 4. The motor’s thermal overload protection has tripped. 5. A fuse has blown or a circuit breaker has been tripped. 6. The air tank pressure exceeds the preset pressure switch limit. 7. The safety valve is stuck open. 8. Electrical connect

  • MasterCraft 8 U.S. GALLON (30.3 L) AIR COMPRESSOR, IMPORTANT INFORMATION 10 8 U.S. GALLONS (30.3 L) AIR COMPRESSOR 058-9316-0 This Mastercraft ® Air Compressor is ideal for a wide range of applications, from fastening to greasing and engine cleaning. The 8-gallon (30.3 L) design provides optimum pressure. It features a 1.5 HP induction motor for quiet operation and a cast-iron, oil-free pump for long-lasting, reliable performance. The procedures described in this manual are solely for this 8-gallon (30.3 L) air compressor at a maximum of P=135 PSI. The device has been designed / constructed for household use only. Compatible compresso

  • MasterCraft 8 U.S. GALLON (30.3 L) AIR COMPRESSOR, STEP 3 Connect the air hose (1) to the compressor’s air outlet (2) with the quick connector (3). STEP 4 Close the tank drain valve (1), located on the bottom of the air tank. page 17, step 7 MC-589316-03 3 1 2 1 MC-589316-04

  • MasterCraft 8 U.S. GALLON (30.3 L) AIR COMPRESSOR, 27 PARTS LIST 8 U.S. GALLONS (30.3 L) AIR COMPRESSOR 058-9316-0 If any parts are missing or damaged, or if you have any questions, please call our toll-free helpline at 1-800-689-9928. No. Description Qty. No. Description Qty. 1 Nut M10 4 20 Fan 1 2 Rubber foot 2 21 Air filter 1 3 Bolt M10x20 2 22 Back shroud 1 4 Drain valve 4 23 Bolt M5x18 4 5 Air tank 1 24 Self-tapping screw ST3.9x17 4 6 Handle 1 25 Bolt M8x25 4 7 Thumbscrew 2 26 Washer Ø8 4 8 Check valve 1 27 Cushion pad 4 9 Regulator 1 28 Bolt M5x10 2 10 Relief valve 1 29 Lock washer 2 11 Quick coupler 1 30 Transfer tube 1 12 Pressure gaug

  • MasterCraft 8 U.S. GALLON (30.3 L) AIR COMPRESSOR, MAINTENANCE 22 8 U.S. GALLONS (30.3 L) AIR COMPRESSOR 058-9316-0 Check the valve Pull/activate the safety valve daily to ensure that it is operating properly and to clear the valve of any possible obstructions. 1. Before starting compressor, pull the ring on the safety valve to make sure that the safety valve operates freely. If the valve is stuck or does not operate smoothly, contact a trained service technician. WARNING! Potential hazard that could result in serious injury or loss of life. • Be sure to wear protective goggles. • Relieve the air pressure in the system and open the drain

  • KEY PARTS DIAGRAM 9 8 U.S. GALLONS (30.3 L) AIR COMPRESSOR 058-9316-0 No. Description No. Description 1 Air tank 7 Outlet pressure gauge 2 Air tank drain valve 8 Tank pressure gauge 3 Power cord 9 Pressure switch 4 Air outlet 10 Electric motor 5 Air pressure regulator 11 Air compressor pump 6 Safety valve MC-589316-07 1 2 3 4 5 6 7 8 9 10 11

  • MasterCraft 8 U.S. GALLON (30.3 L) AIR COMPRESSOR, QUICK START GUIDE 8 U.S. GALLONS (30.3 L) AIR COMPRESSOR 058-9316-0 STEP 1 Set the pressure switch (1) to the OFF position. page 16, step 1 STEP 2 Turn the air pressure regulator knob (1) counter- clockwise unti l it stops. page 16, step 3 1 MC-589316-01 1 MC-589316-02

  • MasterCraft 8 U.S. GALLON (30.3 L) AIR COMPRESSOR, STEP 5 Plug in the power cord (1). page 16, step 4 and page 17, caution STEP 6 Set the pressure switch (1) to the ON position. Turn the air pressure regulator knob (2) clockwise until desired pressure is reached. MC-589316-05 1 1 2 MC-589316-06

Related Products and Documents (Air Compressor):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 DeWalt DW293 Original instructions manual dewalt/dw293-PE9.pdf 12 Jun 2023 16
2 Telex BTR-700 Supplementary manual telex/btr-700-C5A.pdf 17 Sep 2022 1 0.08 Mb
3 Dell B5465dnf Mono Laser Printer MFP Manual  dell/b5465dnf-mono-laser-printer-mfp-53Q.pdf 14 Nov 2022 2 3.81 Mb
4 Canon EOS-1Ds Mark III Instruction manual canon/eos-1ds-mark-iii-2WA.pdf 27 Aug 2023 116 12.89 Mb
5 MECNOSUD IM 5-8 Operating manua mecnosud/im-5-8-777.pdf 11 Sep 2022 29
6 GeoSafari Tuff Scope 5292 Operation & user’s manual geosafari/tuff-scope-5292-KD1.pdf 05 May 2023 2

Similar Resources:

  • Streetwize

    SWAC12

    (2 pages)
    Operating instructionsThe 12V Air Compressor has been engineered to service even the largest tyres used on trucks, vans, 4X4’setc., but will equally as well on passenger cars. Please read the entire instruction manual before use and retain for future reference.IMPORTANT Your battery may not be at full strength. It is essential therefore that you keep your …
  • Power Fist

    8670978

    (20 pages)
    V4.0 8670978 Please read and understand all instructions before use. Retain this manual for future reference. User Manual Portable 12V Air Compressor with LED Light …
  • RIDGID

    OF45150B

    (36 pages)
    © 2004 RIDGID, INC.Numéro de pièce IN610303AV 7/06 Nº de formulaire IN610303AV Imprimé aux États-Unis 7/06GARANTIE LIMITÉE DE TROIS ANS DE COMPRESSEUR D'AIR RIDGID Ce produit est fabriqué par Campbell Hausfeld. La marque de commerce et souslicence de Ridgid, Inc. Toutes les communications sous garantie doivent êtreadressées au service techniqu …
  • California Air Tools

    8010SPC

    (15 pages)
    ULTRA QUIET & OIL FREEAIR COMPRESSOROwnER'S MAnUALCALIFORnIA AIR TOOLS8010SPC*** #%"%'## &#!B@A<:2?&B==<?A …
  • Emerson

    Copeland ZR16

    (22 pages)
    Application Engineering B U L L E T I N AE4-1374 R1 July 2013 ZR16 to ZR54K5E R-22 and R-407C 1.5 to 5 Ton Copeland Scroll™ Compressors TABLE OF CONTENTS Section Page Section Page Safety Suction & Discharge Fittings ....................................10 Safety Instructions .................................................... 2 Safet …
  • Murphy

    S14E-92229N

    (2 pages)
    Information for Four Stage ENGINEDriven Compressor Applications Attachment to Installation and Operation Manual for SELECTRONIC®Annunciator Series 1400 ®S14E-92229NRevised 06-93TYPICAL WIRING DIAGRAM101 COMPRESSOR OIL PRESSURE (LOW) B SHUTDOWN02 COMPRESSOR OIL LEVEL (LOW) A SHUTDOWN03 LUBRICATION NO–FLOW – B SHUTDOWN04 LOW SUCTION PRESSURE (LOW/HIGH) B …

Comments, Questions and Opinions: