Aplex AHM-6XX6A Operation & User’s Manual
|
Aplex AHM-6XX6A, AHM-6XX6A User Manual 81 Plot Calibration Data Check this function and a touch panel linearity comparison graph appears when you have finished Advanced Calibration. The blue lines show linearity before calibration and black lines show linearity after calibration. Turn off EEPROM storage The function disable for calibration data to write in controller. The default setting is Enable. Setting Touch Mode This mode enables and disables the mouse’s ability to drag on-screen icons-useful for configuring POS terminals Beep Sound Enabled Beep Sound – turns beep function on and off Beep on Pen Down – beep occurs when pen comes down Beep on Pen Up –
Aplex AHM-6XX6A, AHM-6XX6A User Manual 55 Example x86 assembly code: mov dx, 4Eh mov al, 0E5h ;GPIO data reg. out dx, al mov dx, 4Fh in al, dx ;Bit[3::0] = GPI[3::0] value Example C code: outportb(0x4E, 0xE5); //GPIO data reg. GP = inportb(0x4F); //Bit[3::0] = GPI[3::0] Write GPIO value Example x86 assembly code: ;Set GPO62 mov dx, 4Eh mov al, 0E5h ;GPIO data reg. out dx, al mov dx, 4Fh in al, dx or al, 00000100b ;Bit2 = GPO62 out dx, al ;Clear GPO62 mov dx, 4Eh mov al, 0E5h ;GPIO data reg. out dx, al mov dx, 4Fh in al, dx and al, not 00000100b out dx, al Example C code: //Set GPO62 outportb(0x4E, 0xE5); //GPIO data reg. Outportb(0x4F, (inportb(0x4F)|0x4)
Aplex AHM-6XX6A, AHM-6XX6A User Manual 58 //Select the logical device 9, GP2 SELETDEV(9) //Read GPIO Value outportb(INDEXP, 0xE5); cGP2 = inportb(DATAP); cGP2 = cGP2 & 0xF; //Exit the super I/O chip programming EXITPRG return cGP2; } //Write GPIO Port6 int WriteGP6(unsigned char cGP6) { //Start the super I/O chip programming ENTERPRG //Select the logical device 8, GP6 SELETDEV(8) //Write GP1 value WRITEREG(0xE5, cGP6) //Exit the super I/O chip programming EXITPRG re
Aplex AHM-6XX6A, AHM-6XX6A User Manual 54 Example C code: outportb(0x4E, 0x30); //Logic device activation control outportb(0x4F, (inportb(0x4F)|0x2)); //Set bit[1] to enable GPIO Port2 if LDN=9 Or outportb(0x4E, 0x30); //Logic device activation control outportb(0x4F, (inportb(0x4F)|0x4)); //Set bit[2] to enable GPIO Port6 if LDN=8 Configure GPIO register Example x86 assembly code: mov dx, 4Eh mov al, 0E6h ;GPIO inversion reg. out dx, al mov dx, 4Fh mov al, 000h ;0 – normal, 1 - inverted out dx, al mov dx, 4Eh mov al, 0E4h ;GPIO I/O selection reg. out dx, al mov dx, 4Fh m
Aplex AHM-6XX6A, AHM-6XX6A User Manual 36 [Device] 3.4.3 Super IO Configuration Serial Port3 Type: COM3 Options: [RS232 Type] or [RS485 Type] [RS232 Type] for RS232 Mode [RS485 Type] for RS485 or RS422 Mode WatchDog Setting: [Disable] Options: [10sec, 20sec, 30sec, 40sec, 1,min, 2min, 4min] 3.4.4 Hardware Health Configuration
Aplex AHM-6XX6A, AHM-6XX6A User Manual 24 of the said tables. Any inconformity may cause system down and even hard ware damages. 7. JCOM: (2.0mm Pitch 2x6 Pin Header) COM1 and COM3 setting jumper, pin 1~6 are used to select signal out of pin 9 of COM1 port; pin 7~12 are used to select output type for COM3 port (RS232 type or RS422 type or RS485 type). JCOM Pin# Function CLOSE 1-2 COM1 Pin9=RI (default) CLOSE 3-4 COM1 Pin9=+5V (option) CLOSE 5-6 COM1 Pin9=+12V (option) JCOM Pin# Function CLOSE 7-9 COM3 FOR RS232 FROM COM3 (default) CLOSE 8-10 COM3 FOR RS485 FROM
Aplex AHM-6XX6A, AHM-6XX6A User Manual 51 Save Changes and Exit: Save configuration changes and exit setup? (F10 key can be used for this operation) [OK] [Cancel] Discard Changes and Exit: Discard Changes and Exit setup? (ESC key can be used for this operation) [OK] [Cancel] Discard Changes: [Discard changes? (F7 key can be used for this operation) [OK] [Cancel] Load Optimized Defaults: Load Optimized Defaults? (F9 key can be used for this operation) [OK] [Cancel] Load Fail-Safe Defaults: Load Fail-Safe Defaults? (F9 key
Aplex AHM-6XX6A, AHM-6XX6A User Manual 70 Click FINISH; A Driver Installation Complete. 4.4 Realtek HD Audio Driver Installation To install the Realtek High Definition (HD) Audio driver, please follow the steps below. Select Audio from the list
Aplex AHM-6XX6A, AHM-6XX6A User Manual 60 Chapter 4 Installation of Drivers This chapter describes the installation procedures for software and drivers under the windows XP. The software and drivers are included with the motherboard. The contents include Intel chipset driver, VGA driver, LAN driver, Audio driver, Touch Panel driver Installation instructions are given below. 4.1. Intel Chipset Driver To install the Intel chipset driver, please follow the steps below. Important Note: After installing your Windows operating system (Window
Aplex AHM-6XX6A, AHM-6XX6A User Manual 85 3. If you change the resolution of display or screen address, you have to redo Map Touch Screens so the system understands where the displays are. 4. If you more monitor mapping one touch screen, Please press ‘S’ to skip mapping step. Tools Draw Tests or demonstrates the PenMount touch screen operation. Advanced Calibration Enable Advanced Calibration function Right Button Icon Enable right button function. The icon can show on Desktop or System Tray (menu bar).
Aplex AHM-6XX6A, AHM-6XX6A User Manual 83 Multiple Monitors Multiple Monitors supports from two to six touch screen displays for one system. The PenMount drivers for Windows 2000/XP support Multiple Monitors. This function supports from two to six touch screen displays for one system. Each monitor requires its own PenMount touch screen control board, either installed inside the display or in a central unit. The PenMount control boards must be connected to the computer COM ports via the RS-232 interface. Driver installation procedures are the same as for a single monitor. Multiple Monitors supports the following modes: Windows
Aplex AHM-6XX6A, AHM-6XX6A User Manual 39 Extended Tag Field: [Auto] [Disabled] [Enable] No Snoop: [Auto] [Disabled] [Enable] Maximum read Request Size: [Auto] [128/256/512/1024/2048/4096 Bytes] Set Maximum Read Request Size of PCI Express Device or allow System BIOS select the value. Active State Power management: [Disabled] [Enable] Extended Synch: [Auto] [Disabled] [Enable] 3.4.9 Smbios Configuration Simbios Smi Support: [Enable] [Disabled]
AHM-6XX6A User Manual 5 Chapter 5 Touch Screen Installation 5.1 Introduction to Touch Screen Controller Board………....73 5.2 Windows 2000/XP USB Driver Installation………………….73 Appendix A Panel Mounting and VESA Mounting 88 Figures
Aplex AHM-6XX6A, AHM-6XX6A User Manual 17 Step 4 Push into the HDD bracket as shown in the picture AHM-6156A. Step 5 Tighten the 2 screws as shown in the picture. That’s how it should look after it has been installed.
Aplex AHM-6XX6A, AHM-6XX6A User Manual 31 Chapter 3 BIOS Setup 3.1 Operations after POST Screen After CMOS discharge or BIOS flashing operation, the system will display the following screen for your further operation. Press F2 key to continue or F1 key to enter CMOS Setup. After optimizing and exiting CMOS Setup, the POST screen displayed for the first time is as follows and includes basic information on BIOS, CPU, memory, and storage devices.
Aplex AHM-6XX6A, AHM-6XX6A User Manual 21 Watchdog Timer Software programmable 1 – 255 second by Super I/O External I/O port 1 x COM Port (COM1) 4 x USB 2.0 Ports (stack) 2 x RJ45 GbE Port (10/100/1000Mbps) 1 x VGA Port 1 x VGA 2x8 Pin Header VGA function is not available for 17” and 19” (AHM-6176A and AHM-6196A) Temperature Operating: 0℃–60℃ Storage: -20℃–70℃ Humidity 5% - 95%, non-condensing, operating Power Consumption 12V /1.6A (Intel D525 processor with 2GB DDR3 DRAM) 12V /1.3A (Intel N455 processor with 2GB DDR3 DRAM) EMI/EMS Meet CE/FCC class A
Aplex ADP-1151W Monitor Operation & user’s manual
ADP-1151W |
Aplex ADP-1174 Monitor Operation & user’s manual
ADP-1174 |
Aplex ADP-1194 Monitor Operation & user’s manual
ADP-1194 |
Aplex ADP-1156 Monitor Operation & user’s manual
ADP-1156 |
Aplex OPD-1086B Monitor Operation & user’s manual
OPD-1086B |
Aplex ADP- 11x6 Monitor Operation & user’s manual
ADP- 11x6 |
ASA Electronics AOM713WP Monitor Troubleshooting manual
AOM713WP |
Aplex ADP-1101 Monitor Operation & user’s manual
ADP-1101 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Haier | LW-120HB | Operation & user’s manual | haier/lw-120hb-R3Q.pdf | 05 Feb 2024 | 28 | 3 Mb |
2 | ViTiny | PRO10 | Operation & user’s manual | vitiny/pro10-MPZ.pdf | 23 Oct 2023 | 25 | |
3 | Zephyr | Breeze I | Use & care and installation manual | zephyr/breeze-i-8Z2.pdf | 21 Nov 2022 | 23 | |
4 | Sony | FCBEH3150 | Technical manual | sony/fcbeh3150-M6D.pdf | 19 Feb 2024 | 61 | |
5 | Custom Audio Electronics | JOHN DEERE 425 | Mounting instructions | custom-audio-electronics/john-deere-425-1UF.pdf | 14 Oct 2022 | 14 | |
6 | Playskool | Humbah | Instructions | playskool/humbah-AD2.pdf | 31 Jul 2023 | 2 |
Sharp
LCD AV MONITORLCD-AV-MONITORMONITEUR AV ÀCRISTAUX LIQUIDESMONITOR AV LCDMONITOR AV LCDLCD-BILDSKÄRMLCD AV-MONITORLC-20M4ELC-20M4EOPERATION MANUALBEDIENUNGSANLEITUNGMODE D’EMPLOIMANUALE DI ISTRUZIONIMANUAL DE MANEJOBRUKSANVISNINGGEBRUIKSAANWIJZINGENGLISHDEUTSCHFRANÇAISITALIANOESPAÑOLSVENSKANEDERLANDSPrinted in JapanJapan in GedrucktImprimé au JaponStam …
LC-20M4E(51 pages) |
OPTICOM
Features19” LCD MonitorSpecificationsLCD MonitorLCDI-19High Resolution TFT LCD PanelHigh Impact Case with Attractive Styling VGA and Analog (BNC Type) Video InputsDual Built-In Speakers with RVA Audio Input60,000 Hour Lamp Life2 Year Warranty19” LCD PanelResolution: 1280 x 1024Brightness: 300 cd/m2Contrast Ratio: 800:1View Angle: 80/80/80/80System: NTSC …
LCDI-19(1 pages) |
Winmate
Please read these instructions carefully before using this product, and save this manual for future use PT Series Multi-Touch Chassis HMI Intel® Celeron® Bay Trail-M N2930, 1.83 GHz Model No. R15IB3S-PTC3 W15IB3S-PTA3 User Guide Part No. 91521110101T Document Version 1.2
…
W15IB3S-PTA3(44 pages) |
Gator
USER MANUALGRV127KTgatordriverassist.comFor more information on the Gator range go to our websiteMirror monitor, Butterfly mount camera, 5.5M RCA extension cable,Adhesive mount, Suction mount, Mirror monitor harness, Camera harness.
…
GRV127KT(12 pages) |
Endress+Hauser
Products Solutions ServicesOperating InstructionsRIA15Loop-powered 4 to 20 mA process display unitwith HART® communicationBA01170K/09/EN/05.1571300896Valid as of FW version:01.04.xx
…
RIA15(64 pages) |
HP
15-inch Color Displays13.9 inch Viewable ImageUser’s Guide15-Zoll-Farbbildschirme13.9 Zoll BildanzeigeBenutzerhandbuchMoniteurs couleur 15 poucesAffichage 13,9 poucesGuide de l’utilisateurPantallas de color de 15 pulgadas13.9 pulgadas de imagen visualizadaManual del Usuario Léase esto primeroVideo a colori da 15 pollici13.9 effetivi per l’immagineManu …
D2830A(20 pages) |
Western Digital Storage Blue WD7500AZEXWestern Digital Storage Blue WD7500AZEX Product features Blue WD7500AZEX, 3 |
Adaptif Photonics Multimeter A1XXXGuide: Adaptif Photonics A1XXX (29O626, Upd.09.09.2023) A1XXX, 133 |
Makita Power Screwdriver BFR540Instruction manual for Makita BFR540 Power Screwdriver BFR540, 52 |
Snapper Lawn Mower 1690785User Guide: Snapper 1690785 (7AUQ7X, Upd.03/09/2023) 1690785, 5 |
Simplicity Automobile Accessories 1693756Simplicity Automobile Accessories 1693756 Operator's manual 1693756, 22 |
Hama Power Pack 00173221 SlimUser Manual: Hama 00173221 Slim (543XBS, Upd.29/10/2023) 00173221 Slim, 18 |
SOMMER Garage Door Opener SG1#61K21Y SG1: SOMMER Garage Door Opener Owner Documentation SG1, 28 |
Phoenix Tablet VEGA TAB 7Phoenix VEGA TAB 7 User Guide (Operation & user’s manual), @9P93OU VEGA TAB 7, 23 |
Toshiba Telephone DKT 2000-seriesDKT 2000-series Quick reference manual - 6ENNI4 DKT 2000-series, 12 |
Curtis Flat Panel TV LCD3215Curtis LCD3215 User Manual (Doc Type: Flat Panel TV Specification sheet) LCD3215, 1 |
HP Desktop TouchSmart IQ524HP Desktop Quick setup (File: hp-iq525-touchsmart-4-gb-ram-quick-setup-1, 29th Oct 2023) TouchSmart IQ524, 1 |
Roadmaster Car Stereo System RM-DVD9001RM-DVD9001 Operation & user’s manual - 1NY994 RM-DVD9001, 29 |