Manualios.com

Aerotech G-Force Assembly And Operation Instructions Manual

Aerotech G-Force Manual Online:

4, 712 votes
Aerotech G-Force User Manual
Aerotech G-Force User Guide
Aerotech G-Force Online Manual

Text of Aerotech G-Force User Guide:

  • Aerotech G-Force, 1 19921-0100 Rev. 8/12/04 COMPLETED G-FORCE™ ADVANCED MODEL ROCKET Read And Follow All Instructions Designed By Ed LaCroix BEFORE YOU BEGIN • Study the illustrations and sequence of assembly. The sequence of assembly is important. Review the parts list and become familiar with all parts before assembly. If any parts are missing or damaged, contact RCS at 1-435-865- 7100 or email at [email protected]. • DO NOT MODIFY THE DESIGN OF THIS ROCKET . Changes to the design of the rocket such as, but not limited to, reducing the fin

  • 2 LOCATION GUIDE 1/4" 6 mm 1/2" 13 mm FIN-LOK™ ASSEMBLY 1. Cement the thrust ring flange (1/16"/1.6 mm thick) to the thrust ring (7/16"/11 mm long). Set the thrust ring assem- bly aside to dry. 2. Find the line drawn along the side of the motor tube. Using the Location Guide printed along the top edge of this instruction sh

  • Aerotech G-Force, 3 FIN-LOK™ ASSEMBLY (CONT.) Screw Eye Front Centering Ring Baffle Flange Motor Tube Permanent Cooling Mesh (Stretch Out - 6") Ejection Gas Baffle Shoulder DO NOT ALLOW CEMENT TO GET IN THE FIN LOCKS Front End DO NOT CEMENT COOLING MESH INTO MOTOR TUBE LABYRINTH™ ASSEMBLY Middle Centering Ring Fin Locks Cement Beads 1/4"/6mm Cuts the finlocks where the front FIN-LOK™ ring meets the middle AERO-FIBRE™centering ring and the motor tube. 6. Without getting cement into any of the fin locks, apply cement only to the areas BETWEEN the fin locks where on

  • Aerotech G-Force, 4 LOWER BODY AND FIN ASSEMBLY 1. Screw the other screw eye all the way into the hole in the bulkhead (3/32"/2.4 mm thick). Apply a bead of cement where the screw eye meets the bulkhead. 2. Pass the free end of the shock cord through the coupler tube (6"/15 cm long) and securely tie it to the screw eye attached to the bulkhead with a square knot. (CAUTION: Do not put cement on the knot or the shock cord. Cement will weaken the shock cord.) 3. Cement the bulkhead to the end of the coupler tube. Fin FIN-LOK™ Tab Fin Slot Launch Lug Slots Motor Tube Assembly Body Tube Launch Lugs 1. Using a hobby knife, carefully remove any body tube material that ma

  • Aerotech G-Force, 5 bowl with warm water and put one or two drops of a dishwashing detergent into the water. 6. Carefully peel a decal off its backing, dip it into the detergent solution and apply the decal to the rocket. The detergent solution prevents the adhesive on the decal from "grabbing" the rocket surface too quickly and allows accurate positioning of the decal. 7. Gently press any air bubbles out from under the decal and then dab the decal dry. 8. Apply the rest of the decals in the same manner. 1. Reference the photograph of the completed G-Force rocket on the first page of these instructions for proper decal pos

  • Aerotech G-Force, 6 OPERATION INSTRUCTIONS 1. RECOMMENDED MOTORS: Only use AEROTECH composite model rocket motors when flying your AEROTECH rocket. See enclosed chart for recommended motors and projected altitudes. 2. RECOVERY SYSTEM PREPARATION: Roll the parachute and shroud lines. Start from the canopy peak and roll the parachute and shroud lines into a tight cylinder that will easily slide into the tube coupler assembly. Place this parachute into the tube coupler assembly followed by the shock cord. Insert the remaining shock cord length into the body tube and

Related Products and Documents (Toy):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 JGC RRMP-3400 Operation & user’s manual jgc/rrmp-3400-461.pdf 18 Sep 2022 28
2 LG HM031M Engineering product data book lg/hm031m-M4X.pdf 27 Jun 2023 76
3 Lorex SHS-2S7LD Quick setup manual lorex/shs-2s7ld-H2M.pdf 25 Aug 2022 2
4 Behringer Ultratone K1800FX Specifications behringer/ultratone-k1800fx-89F.pdf 20 Jun 2023 3 1.72 Mb
5 Ninebot miniPRO Operation & user’s manual ninebot/minipro-Q5P.pdf 13 Mar 2024 12
6 RMG PGC 9300 Maintenance manual rmg/pgc-9300-3LY.pdf 18 Oct 2023 85

Similar Resources:

  • Eduard

    Bismarck 1/350 railings and turrets

    (4 pages)
    ORIGINAL KIT PARTSPŮVODNÍ DÍLY STAVEBNICEPHOTO-ETCHED PARTSLEPTANÉ DÍLYPARTS TO BE REMOVEDDÍLY K ODSTRANĚNÍFILLTMELITREMOVEODSTRANITOPTIONVOLBA?REPLACENAHRADITBENDOHNOUTGRINDOBROUSITSYMETRICAL ASSEMBLYSYMETRICKÁ MONTÁŽDRILL HOLEVRTAT OTVORAPPLY EXPRESS MASK AND PAINT BEFORE GLUINGPOUŽÍT EXPRESS MASK NABARVIT PŘED SLEPENÍMTURRET ATURRET DTURRET …
  • Fisher-Price

    M5644

    (6 pages)
    www.fisher-price.comPlease keep this instruction sheet for future reference, as it contains important information.Requires three “AA” (LR06) alkaline batteries (not included).Adult assembly is required. Tool required for battery installation: Phillips screwdriver (not included).M5644 …
  • Eduard

    M-4A3 Sherman 1/48

    (5 pages)
    G201/5M-4A3 Sherman 1/4828 05528 0551/48 scale detail set for kit • sada detailù pro model Hobby Boss 84803Hobby Boss 84803 1/48ORIGINAL KIT PARTSPÙVODNÍ DÍLY STAVEBNICEPHOTO-ETCHED PARTSLEPTANÉ DÍLYPARTS TO BE REMOVEDDÍLY K ODSTRANÌNÍFILLTMELITeduardREMOVEODSTRANITOPTIONVOLBA?REPLACENAHRADITBENDOHNOUTGRINDOBROUSITSYMETRICAL ASSEMBLYSYMETRICKÁ MO …
  • Reely

    Northern Light

    (36 pages)
    BedienungsanleitungHafenschlepper „Northern Light“Best.-Nr. 1527286Fischkutter „Borkum II“Best.-Nr. 1527285 Seite 2 - 18Operating InstructionsTug boat „Northern Light“Best.-Nr. 1527286Fishing cutter „Borkum II“Best.-Nr. 1527285 Page 19 - 35 …
  • LEGO

    Architecture

    (20 pages)
    Empire State BuildingNew York City, New York, USABooklet available on: Livret disponible sur:Folleto disponible en: Architecture.LEGO.com21002_BI.indd 1 01/03/2011 6:27 PM …
  • Black Horse Model

    Thermal 3.0

    (19 pages)
    SPECIFICATION Wingspan : 3,000 mm 118.1 in. Length : 1,600 mm 62.99 in. Weight : 2.2 kg 4.84 Lbs. Radio : 05 channels. Servo : 06 servos. Electric Motor: BOOST 40 Battery : …

Comments, Questions and Opinions: