Acoustic Image Ten2 EX Owner's Manual

Text of Acoustic Image Ten2 EX User Guide:

• Ten2 Clarus Coda Corus IMPORTANT SAFETY INSTRUCTIONS FCC COMPLIANCE NOTICE 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with a dry cloth. 7) Do not block any ventilation openings. Install in accordance with manufacturer’s instructions. 8) Do not install n

• Acoustic Image Ten2 EX, Welcome The Basics 1 Operation--Electronics 3 Power 3 Preamp 3 Inputs 3 Controls 4 5 Stereo Operation 6 9 Headphone Output 9 Limiter Switch 9 Power Amp 10 Connecting a Speaker 10 Operation with No Speaker 10 Operation--Speaker Cabinets 11 Docking System 11 Speaker Placement 11 Tilt Mechanism 11 Connection an Extension Speaker 12 Presence Switch 12 Description of the Corus Combo 12 Tweeter Level Control 13 Room Coupling Control 13 Description of the Ten2 EX 13 Care 16 Warranty And Repair 16 Low Cut Filter/Phase Reverse Effects Loop 5 Direct Out 6 Mute Switch 6 Control Panel Drawings

• Acoustic Image Ten2 EX, mute switch. The two-channel preamp has a switch that allows the second channel to be disconnected from the main amp and connected to a satellite power amp to create a stereo system. The Coda, Corus and Ten2 combo amps use either the one channel or two channel Clarus head mounted in a speaker cabinet via the docking system. The Coda and Corus use the same cabinet and speaker configuration: a 10 inch downfiring woofer and a 5 inch front firing extended range driver with a presence control. The difference between the two is the woofer.

• Acoustic Image Ten2 EX, 4 optimized to get the best sound from piezo pickups. The XLR input is a low impedance balanced input with sufficient gain to allow microphones to be plugged into it. There is a switchable 10 dB pad to attenuate the mic level when it is too “hot.” Phantom power is available through the connector for powering a mic or outboard preamp and can be activated using the push button switch located next to the connector. To avoid an audible “pop”, set the input level control all the way off when switching on the phantom power. An LED indicates when phantom power is on. In the two channel versions, each channel is identical and can be blended to mix two instruments, 2 micropho

• Acoustic Image Ten2 EX, 6 Direct Out Mute Switch If you are not getting any sound out of the amp, check to make sure that the mute switch is off. Stereo Operation Note that channel 2 will not be heard through the speaker system unless the Ch 2 switch is in the depressed or on position. If you are not hearing channel 2 in the output, check to be sure that the switch is on. An XLR jack is provided for a Direct Out connection that allows the system’s output to be fed to mixing boards of house PA systems or recording studios. As a result, the instrument amplified by the unit can be recorded or further amplified by the house PA system. In the two channel amps and combos, the Direct Out signal is the c

• Acoustic Image Ten2 EX, 8 BYP FX FX BYP CH 2 SWITCHFX CH 1 SWITCHFX CH 2 RETURNFX RTN LEVEL FX HEADPHONE OUTPUT H/P AMP CH 1 RETURNFX RTN LEVEL FX Two Channel Control Panel Input Level Bass Mid Treble Level Input Level Bass Mid Treble Level Channel 1 Channel 2 Send Return Freq Direct Out Master Power Level Effects Phantom Phantom Hall Room Plate Delay Ambient Chorus Flange Off On Off On Off On Low Cut Send Return Ch 1 Ch 2 Post EQ Mute Ch 2 Ground lift Off On 30 60 400 Effects Loop Effects Loop 30 400 60 Phase Inv Freq Low Cut Phase Inv Off On Off On Mic Atten Mic Atten 9 Effects Headphone Output There is a short delay between removal of the plug and the amp coming back on, so expect a pause before you will hear

• Acoustic Image Ten2 EX, 10 to operate under these conditions with lower distortion or without having the overcurrent circuit kick in. The limiter reduces the peak signal that is driving the power amp, thereby reducing its peak output with the result of lower distortion. If you find yourself having to play in extreme conditions that cause the amp or combo to have too much distortion or even signal interruption, engage the limiter and see if that helps the situation. Speakers are connected via Neutrik Speakon connectors (“twist lock” type) located on the rear panel. These connectors are used because of their lo

• Acoustic Image Ten2 EX, 12 the tilt stand at all times in order to aim the high frequency output of the speaker toward your ear so that you can better hear the amp. An extension speaker (ideally, one of our cabinets which is matched to the specific combo unit) can be connected to the amp to increase its output level using the jack provided on your amp’s rear panel. Speakers are connected via Neutrik Speakon connectors (“twist lock” type). These connectors are used because of their low contact resistance and non-shorting operation. The output of each Speakon connector is wired to pole “1”. Ma

• Acoustic Image Ten2 EX, System (all models) Amp Head Frequency Response 30 Hz-18 kHz (40-14 kHz ±3 dB) 50 Hz- kHz (60-1 kHz ) Corus Max SPL >112 dB at 1 meter, (Corus), >118 dB/m (Ten2) AC Power 100-115V/50/60 Hz or 220-240V/50 Hz, switchable, Size 12”Hx15”Wx13”D (Coda, Corus, EX) Weight 22 lbs (Coda, Corus, 19 lbs (EX) 32 lbs (Ten2), 25 lbs (EX) 4 lbs (Clarus) Frequency Response 20 Hz - 20 kHz ( Mic Input 600 ohm balanced, XLR connector, switchable 10 dB pad Phantom Power 48 volts, on/off switch w/LED indicator Instrument Input 1 M impedance, 1/4 inch jack Direct Out +4

• Care Warranty and Repair Acoustic Image combos and cabinets are made from injection molded polymer materials. Alittle care will keep yours looking new for years to come. Use a clean, dry cloth to clean the cabinet and metal parts of the amplifier. We stand behind our products with a full warranty of five years from the date of purchase. Speaker components are

More Instructions:

	Acoustic Image Ten2 EX Owner's manual 28-09-2022 8	DOWNLOAD
	Acoustic Image Ten2 EX Owner's manual 22-03-2024 12	DOWNLOAD

Related Products and Documents (Speakers):

Comparable Devices:

Similar Resources:

• Iluv Aud Mini 6 (2 pages) Pulse o repetidamente para ajustar el volumen. Pulse y mantenga pulsado para cambiar de pista.Appuyez plusieurs fois sur ou pour régler le volume. Appuyez et maintenez enfoncé pour changer de piste.反复按动 或 以调节音量。按住转换曲目。QSG100%(Apple device shown as an example)(Dispositif …

• Sony LF-S50G (2 pages) Wireless SpeakerLF-S50G Operating InstructionsLF-S50G_UC (GB)_4-727-167-14(1)Setup How to use1Connect the AC adaptor. Talk to your Google Assistant. Touch-free Gesture Control Volume Operations2Install the Google Home app.3 Set up Wi-Fi with App.Install the Google Home app on a smartphone/iPhone. Follow the directions in the app to set up your speaker with W …

• Clay Paky C61330 (32 pages) 1C61330C613311INSTRUCTION MANUALENGLISH ALPHA PROFILE 1500ALPHA PROFILE 1500 STINDEXPage Contents2 Safety Information3 Unpacking and preparation4 Installation and start-up5 Control panel7 Menu setting16 Maintenance24 Technical information24 Cause and solution of problems25 Channel functionsCongratulations …

• Audio Note Speaker Kit (14 pages) Copyright © 2006 Audio Note (UK) Limited Website www.audionote.co.uk E-Mail [email protected] Telephone +44 (0) 1273 731498 Page 1 Manual Version 1.4 - February 2007 …

• Philips HSB4383/98 (2 pages) HDMI IN13521Register your product and get support atwww.philips.com/welcomeHSB43834FM ANTZH-TWᇼ஥஄ZZZSKLOLSVFRPVXSSRUW˞ͶͿ੬ؿԚ͂ʹ˫yENPrint your user manual at www.philips.com/support3AV I N …

• Valcom V1220 (2 pages) DUAL INPUT AMPLIFIED CEILING SPEAKERMODEL V-1220DESCRIPTION:Ceiling flush mount dual input 8" speaker assembly, complete with speaker, amplifier, 2 separate built-involume controls and round grille.SPEAKER ELEMENTCone Diameter: 8" (20.32 cm)Voice Coil Impedance: 45 OhmsINPUTSImpedance: > 600 Ohms nominalSignal Level : -10 dBm line levelOUTP …

Comments, Questions and Opinions: