ACTi KCM-5211 Hardware Manual

Text of ACTi KCM-5211 User Guide:

• ACTi KCM-5211, www.acti.com KCM-5211 Hardware Manual 2 Table of Contents Precautions 3 Safety Instructions ........................................................................... 4 Introduction 6 Package Contents ............................................................................. 6 Physical Description ........................................................................ 7 Basic Connections ......................................................................... 10 Serial Port Connection .............

• ACTi KCM-5211, www.acti.com KCM-5211 Hardware Manual 3 Precautions Read these instructions You should read all the safety and operating instructions before using this product. Heed all warnings You must adhere to all the warnings on the product and in the instruction manual. Failure to follow the safety instruction given may directly endanger people, cause damage to the system or to other equipment. Servicing Do not attempt to service this video device yourself as opening or removing

• ACTi KCM-5211, www.acti.com KCM-5211 Hardware Manual 4 Safety Instructions Don’t use the power supply with other voltages This device is likely to be damaged or damage other equipments / personnel, if you use a power supply with different voltage than the one included with this device. All warranty of this product will be voided in the situations above. Don’t open the housing of the product Cleaning Disconnect this video product from the power supply before cleaning. Attachments Do not use attachments not recommen

• ACTi KCM-5211, www.acti.com KCM-5211 Hardware Manual 5 operation. Safety Check Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks to determine if the video product is in proper operating condition.

• ACTi KCM-5211, www.acti.com KCM-5211 Hardware Manual 6 Introduction Package Contents KCM-5211 QIG Product CD Terminal Blocks for Power, DI/O and Serial Port Accessories Warranty Card *For the mounting block, please attach the flat side towards the front of camera. There are two types of mounting blocks, and this device uses the black version.

• ACTi KCM-5211, www.acti.com KCM-5211 Hardware Manual 7 Physical Description 1) Digital Input / Output Used in applications like motion detection, event triggering, time lapse recording, alarm notifications, etc., the I/O terminal connector provides the interface to: • 2 Transistor Outputs - For connecting external devices such as relays and LEDs. Connected devices can be activated by Output buttons on the Live View page or through video management software. Connect DO1 and DO2 to their closest 12V pin to activate. • 2

• ACTi KCM-5211, www.acti.com KCM-5211 Hardware Manual 8 2) Serial Port This port connects to serial devices via RS-485 or RS-422 protocols. Use the supplied serial port terminal block to connect the wires from the camera to the serial device. See Serial Port Connection on page 11 for connection details. 3) Ethernet Port The IP device connects to the Ethernet via a standard RJ45 connector. Supporting NWAY, this IP device can auto detect the speed of local network segment (10Base-T/100Base-TX Ethernet). 4) Reset Button Step 1: Switch off IP device by disconnecting the power cable Step 2: Press and continue to hold the Reset B

• ACTi KCM-5211, www.acti.com KCM-5211 Hardware Manual 9 On (3s) On 1s Power On About 20 Seconds Stay On Off (about 15s) Off (10~15s) Restore to Default Complete 5) Audio Input / Output The IP device supports audio input and output with earphone jack 6) Micro SDHC Card Slot Insert your Micro SDHC card here for local recording on camera 7) Power LED This LED light will indicate current camera status. 8) Power Input If you use Power Adaptor to run the device, please connect the power adaptor to the terminal block in the way shown below.

• www.acti.com KCM-5211 Hardware Manual 10 Basic Connections Follow the procedures below to connect the IP device to the respective apparatuses. If you have a PoE(Power over Ethernet) supported switch or injector: 1) Connect your IP Box Camera to the Switch / Injector by CAT5 or CAT6 cables with RJ45 connector. 2) Connect

• www.acti.com KCM-5211 Hardware Manual 11 Serial Port Connection The zoom camera can be connected to a Pan-Tilt (PT) Scanner (Pan-Tilt Head) using the serial port connector. This allows the zoom camera to do pan and tilt using the Pelco-D protocol. Most PT scanners accept Pelco-D and Pelco-P protocol commands via RS-485 or RS-422 connec

• ACTi KCM-5211, www.acti.com KCM-5211 Hardware Manual 12 For more information on connecting PT scanners, please refer to the Knowledge Base article: Pan and Tilt Scanner for ACTi Zoom Cameras (http://www.acti.com/support/KnowledgeBase/outside/detail.asp?KB_ID=KB20110120001) available on the website.

• www.acti.com KCM-5211 Hardware Manual 13 Accessing the Camera Configure the IP Address In order to be able to communicate with the camera from your PC, both the camera and the PC have to be within the same network segment. In most cases, it means that they both should have very similar IP addresses, where only the last number of the IP address is different from eac

• ACTi KCM-5211, www.acti.com KCM-5211 Hardware Manual 14 If you work with our cameras regularly, then there is even a better way to discover the cameras in the network – by using IP Utility. The IP Utility is a light software tool that can not only discover the cameras, but also list lots of valuable information, such as IP and MAC addresses, serial numbers, firmware versions, etc, and allows quick configuration of multiple devices at the same time. The IP Utility can be downloaded for free from http://www.acti.com/IP_Utility When you launch IP Utility, the

• www.acti.com KCM-5211 Hardware Manual 15 Use the default IP address of the camera If there is no DHCP server in the given network, the user may have to manually assign the IP addresses to both the PC and the camera to make sure they are in the same network segment. When the camera is plugged into the network and it does not detect any DHCP services, it will

• ACTi KCM-5211, www.acti.com KCM-5211 Hardware Manual 16 Manually adjust the IP addresses of multiple cameras If there are more than one camera to be used in the same local area network and there is no DHCP server to assign unique IP addresses to each of them, all of the cameras would then have the initial IP address of 192.168.0.100, which is not a proper situation for network devices – all the IP addresses have to be different from each other. The easiest way to assign cameras the IP addresses is by using IP Utility: With the procedure sh

• ACTi KCM-5211, www.acti.com KCM-5211 Hardware Manual 17 Access the Camera Now that the camera and the PC both have their unique IP addresses and are under the same network segment, you can use Microsoft Internet Explorer on the PC to access the camera. Note: Only Microsoft Internet Explorer is supported by the camera at the time of writing this documentation. Please refer to our website (www.acti.com) for future upgrades. Internet Explorer supports the following functionalities: Functionality Internet Explorer Live Video Yes Live Video Area Re

• ACTi KCM-5211, www.acti.com KCM-5211 Hardware Manual 18 Upon successful connection to the camera, the user interface called Web Configurator would appear together with the login page. The HTTP port number was not added behind the IP address since the default HTTP port of the camera is 80, which can be omitted from the address for convenience. Before logging in, you need to know the factory default Account and Password of the camera. Account: Admin Password: 123456 For further operations, please refer to the Firmware User Manual.

More Instructions:

ACTi KCM-5211 Operation & user’s manual 15-09-2022 18

DOWNLOAD

Related Products and Documents (IP Camera):

Comparable Devices:

Similar Resources:

• VADDIO RoboSHOT 12 (44 pages) © 2015 Vaddio - All Rights Reserved. RoboSHOT QSR Systems - Document Number 342-0794 Rev C VADDIO™ ROBOSHOT™ SERIES CAMERAS RoboSHOT 12 and RoboSHOT 30, HD Robotic PTZ Camera Systems featuring the Quick-Connect™ SR Interface System Model and Part Numbers RoboSHOT 12 QSR System, 999-9905-000 (North America), …

• Grandstream Networks GXV3672_HD (39 pages) Grandstream Networks, Inc. GXV3672_HD/GXV3672_FHD Outdoor Day/Night IP Camera VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299 …

• Vitek VTC-TNB42R3F (8 pages) VITEKVITEKFEATURES• 1/3” 3.0 Megapixel Progressive Scan CMOS image sensor• Up to 30fps live view @ 1920x1080 (2MP) / 15fps live view @ 2048x1536 (3MP)• 2.8~12mm Varifocal Lens (VTC-TNB36R3V) / 3.6mm Fixed Iris Lens (VTC-TNB42R3F)• 42 Infrared LED’s with 150’ IR Range (VTC-TNB42R3F) / 36 Infrared LED’s with 120’ IR Range (VTC-TNB36R3V) • W …

• Velleman CAMIP5N1 (114 pages) CAMIP5N1 WIRELESS IP COLOUR CAMERA DRAADLOZE IP KLEURENCAMERA CAMÉRA COULEUR IP SANS FIL CÁMARA IP INALÁMBRICA A COLOR DRAHTLOSE IP-FARBKAMERA BEZPRZEWODOWA KOLOROWA KAMERA SIECIOWA CÂMARA IP SEM FIOS A CORES USER MANUAL 3 GEBRUIKERSHANDLEIDING 18 MODE D’EMPLOI 33 MANUAL DEL USUARIO 49 BEDIENUNGSANLEITUNG 65 INSTRUKCJA OBSLUGI 81 MANUAL DO U …

• urmet domus 1092/258H (8 pages) DS1092-558 MICROCAMERA AHD 1080P DAY & NIGHT OTTICA FISSA 3,6MM 1080P AHD MICROCAMERA 3,6MM FIXED LENS BUILT-IN 1080P AHD MICROKAMERA FESTOBJEKTV 3,6 MM MICROCAMÉRA 1080P AHD DAY & NIGHT FESTOBJEKTV 3,6 MM MICROCÁMARA DÍA/NOCHE AHD 1080P CON LENTE FIJA 3,6 MM INTEGRADA Sch./Ref./Typ/Réf. 1092/258H GUIDA RAPIDA QUICK GUIDE SCHNELLANLE …

• Lorex Vantage LBC7051 (2 pages) FOR SUPPORT AND INFORMATION, VISIT WWW.LOREXTECHNOLOGY.COMProduct InformationUser ManualsQuick Start GuidesSpecification SheetsSoftware UpgradesFirmware UpgradesContents•Weatherproof IR camera•Mounting screws x 4 / 2 x Allen key•Mounting template x 1•60ft BNC / power extension cable•BNC female / RCA male adapter•Power adapter255 …

Comments, Questions and Opinions: