Manualios.com

a2b Obree Owner's Manual

a2b Obree Manual Online:

3.7, 1682 votes
a2b Obree User Manual
a2b Obree User Guide
a2b Obree Online Manual

Text of a2b Obree User Guide:

  • a2b Obree, 65 Remounting the rear wheel Carry out the steps of removal (7-1) in reverse order. A. Remount the torque support. Otherwise, the frame may be damaged. B. Ensure that the rear wheel is centred in the frame before safely tightening the hub axle nuts using 60 Nm. C. Make sure that the brake disk has correct fit between the brake calipers and the wheel is turning freely without the brake blocks dragging on it. If such installation and adjustment of the brake is not completely clear, ask your A2B specialist dealer to adjust the brakes of your A2B for you. Incorrectly adjusted brakes

  • 76 Owner’s manual No. Step inspection 7 8 9 10 11 Date Signature / stamp of the A2B specialist workshop Steering head • Check bearing play of steering head and adjust or replace, if necessary Component assembly: Derailleur system • Clean and lubricate derailleur mechanism and derailleur. • Check derailleur system cord and outer

  • a2b Obree, 43 • Has the sMMI lock been activated by the specialist dealer? If so, the sMMI only operates with the designated motor (see section 3.2.14 - Anti-theft measures). • Do the sMMI contacts on the dock spring back properly? Press the 8 pins into the dock one after the other using your finger. Check if the pins spring back. If the pins are stuck, use contact spray. The battery cannot be charged • Are there any deposits (such as metal filings) on the magnetic plug of the charger? Carefully check the charger plug and the battery socket for deposits. • Is the ambient temperature <0°C? The battery ca

  • a2b Obree, 49 6.2.4 Safety instructions and warnings on the transport and dispatch of the battery Lithium-ion cells are used in the A2B neodrives battery. Therefore, relevant statutory provisions are applicable to the transport and dispatch of the battery which have to be strictly complied with. For instance, a defective battery pack must never be transported in planes as a basic principle. If your battery is defective, please take it to your specialist dealer in person since dispatch of lithium-ion batteries by post or other forwarders is stricly regulated. We recommend to contact your specialist dealer also in t

  • 28 Owner’s manual Important notes If the battery is fully charged, the braking assistant may be activated, but not actively used. This is only possible if the battery charge level is <90%. Therefore, the symbol of the fully charged battery (a) instead of the activated braking assistant (b) symbol is shown in field [11] of the display. Now, the sMMI's software waits for the ba

  • a2b Obree, 42 Owner’s manual 5.6.2 sMMI • The contacts of the sMMI dock are spring loaded and should be cleaned from time to time using a contact spray to ensure they operate flawlessly and for a long time. • The sMMI casing must only be cleaned using a damp (not wet) cloth. 5.7. Transport The following information has to be observed when transporting the Pedelec by car: • Protect all components of your Pedelec from moisture and dirt by taking appropriate measures. • Remove the battery and sMMI from the bicycle before attaching the Pedelec to the

  • a2b Obree, 11 3.5 Adjustment of the handlebars 1. Loosen the screws A using an appropriate Allen key. 2. Align the handlebars centrically with respect to the stem. 3. Turn the handlebars to achieve the desired angular position. 4. Tighten the screws A evenly using 5 Nm. 3.6 Adjustment of the variable stem Alignment of the handlebars stem 1. Loosen the screws B using an appropriate Allen key. 2. Align the stem with respect to the front wheel. 3. Tighten the screws evenly using 15 Nm. Angle adjustment of the stem 1. Loosen the screw C using an appropriate Allen key. 2. Position the stem i

  • a2b Obree, 57 7.0 Important safety instructions before your first tour Make sure that you and your A2B are prepared for a safe and pleasant ride. ALWAYS wear an approved bicycle helmet. If you lend your A2B to some else, you should always lend an approved helmet, too. NEVER transport another person on your A2B. Overloading your A2B by transporting another person may cause severe or even fatal injuries. FOLLOW all traffic rules. Always ride on the correct side of the road, in the direction of the traffic and not in the opposite direction. Beware of vehicle doors. Remember that doors of vehicles in front of you might be opened.

  • a2b Obree, 71 No. Step inspection 1 2 3 4 5 6 Component assembly: Frame-handlebars-stem-saddle post-saddle • Check components for cracks and replace, if necessary • Check screws on handlebars/stem/saddle • Clean & lubricate saddle post pipe Front fork • Completely clean suspension fork, espec. sliding surfaces of the standpipes • Check standpipes for damage, replace, if necessary Rear wheel slot • Clean TMM4 sensor using air, without demounting it • Check firm fit & state of the sensor plate • Check axle

  • a2b Obree, 64 Owner’s manual Removing the rear wheel 1. Ensure that the battery is not connected to the system any more. To that end, remove the battery from the vehicle. 2. Remove the cable holders (on the back of the dropout and on the bottom side of the left chain stay) using an appropriate Allen key. 3. Disconnect the plug connectors for the power and control cables leading to the motor. 5 3 2 4 7 6 1 4. Loosen and remove the hub axle nuts using a 19-mm wrench. 5. Loosen and remove the retaining screw of the torque support on the left-hand side of the dropout. 6. Remove the torque s

  • a2b Obree, 18 Owner’s manual Smart MMI Display control * Monochrome Display diagonal size, resolution 2.4 inches, 240 X 320 pixels Dimensions sMMI without dock 53 mm x 85 mm x 14 mm (W X L X H) Connectivity Micro-B 1.1 USB, 5-volt power supply, 500 mA connection to PC, incl. diagnostic and parameterisation software Mechanical/electrical contacting Twist-to-lock, corrosion-proof contacts, spring loaded Lighting LED Backlight, 70 – 350 cd/ m² Display plate Scratchproof, quenched and tempered acrylic glass plate Weight sMMI (detached) 55 g 5.1.6 Technical data Drive Range* Up to 120 km Speed 25 km/h Rated power (peak) 250 watts (650 watts) Operating voltage 36 volts

  • a2b Obree, 4 Owner’s manual 1.0 Introduction Welcome and congratulations on buying your new A2B Obree, the electric bike that’s taking transport in a whole new direction. It’s the revolutionary way to get to work, visit the shops or just get some fresh air. Compared to jumping in the car, an ebike is a lot more fun, easier to park and will reduce your fuel costs as well as your impact on the environment… as you’ll soon find out! Feeling energetic? You can ride your new A2B Obree powered off and then switch the assistance on for hills and he

  • a2b Obree, 9 3.4 Adjustment of the seat height The seat height may have to be adjusted. Please ask your A2B specialist dealer to adjust the seat height before your first tour. You may also adjust the seat height on your own as indicated below: Determination of the correct driver's seat height There are several ways of determining the correct seat height; the method which can be carried out without any further auxiliary means is described in the following: Sit on the saddle and stretch one leg. Put your foot&apos

  • a2b Obree, 1.0 Introduction 4 2.0 Important information 5 3.0 Your A2B 6 4.0 Please familiarise with the functions of your A2B before your first tour 12 5.0 Operating instructions display and motor 16 5.1.1 Important instructions – please observe in any case! 16 5.1.2 Intended use of the neodrives components 16 5.1.3 Admissible operating conditions / places of use 17 5.1.4 Standard scope of supply 17 5.1.5 Technical data 18 5.2. Controller 20 5.3. smart Man-Machine Interface (sMMI) 20 5.3.1 Fitting and removing the sMMI 22 5.3.2 Functions of the sMMI 23 5.3.2.1 Switching on and off 23 5.3.2.2 S

  • a2b Obree, 77 No. Step inspection Date Signature / stamp of the A2B specialist workshop Date Signature / stamp of the A2B specialist workshop Date Signature / stamp of the A2B specialist workshop Date Signature / stamp of the A2B specialist workshop Date Signature / stamp of the A2B specialist workshop Date Signature / stamp of the A2B specialist workshop Date Signature / stamp of the A2B specialist workshop Date Signature / stamp of the A2B specialist workshop Date Signature / stamp of the A2B specialist workshop Further maintenance: every 2,000 km after 4,000 km after 6,000 km after 8,000 km after 10,000 km after 12,000 km after 14,000 km after

  • a2b Obree, 59 Tyre pressure. Your A2B is equipped with very durable bicycle tubes to prevent punctures. Bicycle tyres, however, usually lose pressure over time. Poorly inflated tyres might fail prematurely and mean that you have to use more power (pedalling power and motor power) to move your A2B forward. Low tyre pressure reduces the range which is possible per battery charge. The recommended tyre pressure for the front and rear wheel tyre is 2.8 bar. Quick release. Ensure that the quick releas

  • 37 Whenever a motor is operated beyond the optimum operating point, its efficiency decreases. This results in the energy not being optimally converted any longer, but a part of the supplied energy is converted into heat. In this way, the range decreases and the heat must be discharged. In the neodrives motors this heat is discharged through a large contact surface inside the

  • 54 Owner’s manual 6.5. Charging the battery Completely charge the battery before using it for the first time. The battery's state of charge in general is 30% upon delivery. The battery may be charged in every state of charge without affecting the life cycle. The battery reaches its maximum life cycle if charged at an ambient temperature between 10°C and 30°C

  • a2b Obree, 25 5.3.2.3 Dynamo function and switch-on routine "light“ (optional) The neodrives motor features a dynamo function and supplies the headlamp on your Pedelec with power even if the battery is flat, not attached or defective. Thanks to this function, a standard bicycle dynamo on the front wheel may not be required. In the normal Pedelec mode, the bicycle headlamp is supplied with 36 volts from the battery pack. When switching on the bicycle lighting, a certain sequence must be followed for electr

  • 75 Further maintenance: every 2,000 km No. Step inspection 1 2 3 4 5 6 Component assembly: Frame-handlebars-stem-saddle post-saddle • Check components for cracks and replace, if necessary • Check screws on handlebars/stem/saddle • Clean & lubricate saddle post pipe Front fork • Completely clean suspension fork, espec. sliding surf

  • a2b Obree, 50 Owner’s manual • Do not subject cable and plug to pressure. Excessive stretching or bending the cables, pinching a cable between a wall and a window frame or putting heavy objects on a cable or a plug may lead to an electric shock or fire. • Lay the power cable and the attached charging cable in such a way that nobody can step on it or stumble over it and that both cables are not subject to any other damaging effects or influences. • Do not operate the charger if the power cable, the charging cable or the plugs fixed to the cables are damaged. All damaged parts must be replaced immediately by the authorised speciali

  • a2b Obree, 5 2.0 Important information This owner’s manual contains important safety, performance and service information. Please ensure that users of your A2B Obree read and understand the following important warnings and cautions before their fi rst trip. If you have any questions or are not sure about any instructions in this owner’s manual ask your A2B dealer. Read and understand the following warnings and cautions. If your A2B Obree is used by others, please show this section to them so that they are aware of these important warnings to reduce the risk of an accident. Important terms. Throughout the manual, the following symbols and terms call y

  • a2b Obree, 60 Owner’s manual 8.0 Maintenance Have your A2B checked and maintained regularly by an A2B specialist dealer and in accordance with the maintenance schedule (see section 13 of these operationg instructions), however, at least once a year. 8.1 Wheels The front and rear wheels should be aligned centrically in the fork and the frame. Regularly check the wheels for correct spoke tension and rim alignment. Do NOT use your A2B if the spokes are damaged or missing. The wheels should run smoothly and without horizontal or vertical wobble. 8.2 Hub bearings Regularly check the fit of the hub bearings by lifting the wheel from th

  • a2b Obree, 48 Owner’s manual • Do not expose the battery to any kind of moisture (water, rainwater, snow, etc.) during storage! • Charge the battery before storage and check the state of charge every 3 months. • Store the battery in a cool and dry place where it is safe from damage and unauthorised access. • To obtain an optimum battery life cycle, the battery should be stored at a temperature from 18°C to 23°C and a humidity of 0 to 80 per cent. The state of charge should be 70 per cent. • Check the battery's state of cha

  • 27 Automatic recuperation (optional) Depending on the Pedelec's equipment by the manufacturer, recuperation can also be activated automatically by operating the rear wheel brake. By doing so, energy is automatically fed into the battery during every braking process. To ensure controlled and safe braking, recuperation during braking is made with 40% energy recovery. Recuperation

  • a2b Obree, 78 Owner’s manual 14.0 Owner registration You should complete your owner registration card immediately and return it or register online on www.wearea2b.com so that we may send you important information in the future. Thank you. Your A2B and certain main components have unique serial numbers. You should note these numbers if you wish to stake out warranty claims later or if your bicycle gets lost or is stolen. The vehicle serial number can be found on the bottom side of the frame near the pedal crank: Vehicle serial number: The motor serial number is engraved on the left-hand side of the motor hub: Motor serial number: Note this further important information:

  • a2b Obree, 41 Never mount the motor without the torque support [20]. This would lead to a total loss (twisting off the cable). In this case, all warranty or guarantee claims shall become void. Carry 5 cable ties along with you apart from your repair tool to be able to refasten any loose cables during a tour securely. Mounting or removing the drive wheel can best be carried out if the Pedelec is turned upside down (put on handlebar and saddle). Remove the sMMI fixed to the handlebar first to avoid damage. 5.6. Cleaning of the motor and sMMI N

  • a2b Obree, 53 6.4. Removal of the battery 6.4.1 Switching off the battery The battery is switched off using the controller of the sMMI (see operating instructions neodrives sMMI and motor). While doing so, the battery is first put into "Active mode" for 48 hours. This means that the sMMI can be reactivated at any time during this period without having to switch on the battery first. The power required in this context is minimal. 6.4.2 Removing the battery • Open the cover flap on the luggage rack battery. Put the key into the lock on the luggage rack battery • Push the key slightly into the lock and, while doing so, turn

More Instructions:

DOWNLOAD

Related Products and Documents (Scooter):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Panasonic AJD850 - DVCPRO STUDIO VTR Operating instructions manual panasonic/ajd850-dvcpro-studio-vtr-S18.pdf 20 Mar 2024 104 1.17 Mb
2 Snapper 1600222 Installation instructions snapper/1600222-881.pdf 15 Dec 2022 1 0.02 Mb
3 Dell Professional P2412H Product dimensions dell/professional-p2412h-17U.pdf 11 Feb 2024 1 0.07 Mb
4 Kramer WP-210AE Operation & user’s manual kramer/wp-210ae-199.pdf 19 Jun 2022 14
5 Double Power Technology D7015 Operation & user’s manual double-power-technology/d7015-655.pdf 18 Nov 2023 24 4.17 Mb
6 Clarity S-503 Specifications clarity/s-503-H2O.pdf 04 Feb 2024 6 0.09 Mb

Similar Resources:

  • BOHLT

    EKICK 9 PRO

    (54 pages)
    BOHLT EKICK 9 PRO 9 PROGebruikershandleidingLees deze handleiding alstublie� goed door voordat u deze step gaat gebruiken. Bewaar deze handleiding voor latere raadpleging. …
  • Razor

    Kiddie Kick

    (5 pages)
    © 2006 Copyright Razor USA LLC. All rights reserved.Specifications subject to change without notice.Photos by Arthur Cambridge. Rev: 04/06SPECIFICATIONS SUBJECT TO CHANGERazor USA LLCCerritos, California 90703www.razor.comIMPORTANT NOTICES Read the owner’s manual thoroughly prior to assembly. Be careful not to misplace or lose small parts when unpack …
  • Pride

    Jazzy 600 Series

    (2 pages)
    (US) 800-800-8586 § (Canada) 888-570-1113Visit us on the web: www.pridemobility.comJazzy® 600shown in Candy Apple RedThe Jazzy® 600 provides excellent performance and maximum stability. Its compact design and standard ATX Suspension allows it to excel indoors and out, making it a superb, all-around power chair choice. …
  • Dominator

    Sniper

    (8 pages)
    RIDERʼS MANUALRead and understand this manual prior to riding your Domintator® scooter.Designed and manufactured by District®, equiped with Eagle Supply® wheels for Dominator®• • • Note: Product illustrations are used for assembly purposes only. …
  • MOGOBIKE

    MB-6000-UD

    (20 pages)
    User Manual MB-6000-UD Rev. 1.03 …
  • Coleman Powersports

    CT200U-EX

    (39 pages)
    READ THIS MANUAL CAREFULLY!POWERSPORTS (888)-405-8725 Coleman Powersports 1775 E. University Dr. Tempe, AZ. 85281 Recommended Age 13+ Provincial / Municipal governments have dierent regulations pertaining to owning and operating an o-road vehicle, learn the regulations in your area.www.colemanpowered.comOWNER’S MANUALCT2 …

Comments, Questions and Opinions: