aakar AAKARv2 Operation & User’s Manual

Text of aakar AAKARv2 User Guide:

• aakar AAKARv2, Control Panel: Prepare >> Preheat ABS (or Preheat PLA) 2. After temperature stabilizes, press extrude few times. In panel you should go to: Prepare >> Extrude >> Extrude 3. If you have no filament loaded, you should feed it in as shown below 2. Load the spool on spool holder 1. Push the filament in filament tube till it comes out from other end

• CURA SOFTWARE The preferred software for your Aakar v2 is Cura from Ultimaker. This software package prepares your 3D model into instructions that Aakar v2 uses to produce an object. 1. Aakar v2 specific version of the Cura software package can be downloaded from the downloads section on our website: www.digitalspares.in/aakar/downloads/cura 2. Download the latest version of C

• aakar AAKARv2, FROM YOUMAGINE.COM TO LOAD FILE IN CURA Now that you are familiar with Cura we continue to explain how you can download a 3D file from YouMagine.com and load this into Cura. YouMagine.com is an online community for 3D printing. 1. Open your browser and go to www.youmagine.com 2. Use the search field at the menu bar next to the magnifying glass to find a model of your interest. Let’s search for example “coffee cup” and ‘Enter’. 3. Choose a design you like. 4. The following page will provide you a ‘Download’ button where you can get your .stl fi

• aakar AAKARv2, Build plate screws: These screws can adjust the leveling of the build plate. Print head: The assembly that melts the filament while the material is pushed through the nozzle onto the build plate. Print head fan: The fan which cools the filament as soon as it is put onto the build plate. Push button: By rotating and pushing the button in front of the Aakar v2, you can access the control panel. SD-card: Secure Digital memory card that can store digital data. It has to be formatted with FAT16 or FAT32 Slicing: The process that turns a 3D model into code that can be used with 3D printers.

• aakar AAKARv2, USB Connectivity Driver installation instructions for Windows. NOTE: In Linux and Mac OS based systems no drivers are required. For windows7 drivers can be downloaded from our downloads section, Linux and MacOSX natively support Aakar v2. NOTE: offline printing doesn’t require driver as Aakar v2 is natively supported as Mass storage device 1. Just plug USB cable located in side panel, and wait until all devices are discovered by your system. 2. A new disk drive should be discovered automatically. For Offline printing drivers need to be installed for Windows system.

• aakar AAKARv2, Terms of Service Returning of purchased item. ** LIMITED ** Returns are accepted on a very limited basis: for any electronic items, returns are accepted only on unaffected devices within 15 calendar days from the date of receipt. “Unaffected” means a device has never been assembled, powered up, programmed, or otherwise changed. Similarly, for non-electronic items, returns are accepted only on unopened items within 15 calendar days from the date of receipt of merchandise. After 15 days, all sales are considered final

• aakar AAKARv2, Levelling screws are located at the bottom of heated bed. Use hex wrenches to rotate these screws. Clockwise rotation moves the bed down i.e. away from nozzle. Anti-clockwise rotation moves the bed up i.e. closer to nozzle. Cura can be used to level the Print bed. Connect your printer to PC and Run Expert > Run bed levelling wizard… And follow the wizard instructions

• aakar AAKARv2, Table of Contents A. Welcome to the Aakar v2 A1. Safety First A2. Specifications A3. Machine overview A4. Accessories B. Getting started with software B1. Cura software B2. Cura software interface B3. From YouMagine.com to load file in Cura B4. Preparing a 3D model C. Getting started with hardware C1. Printer connection C2. Testing and Caliberation C3. First print D. Maintenance D1. In General D2. Software Updates D4. Changing Toolheads E. Terminology F. Terms of Service

• aakar AAKARv2, PREPARING A 3D MODEL 1. Most 3D printable files that you will find on YouMagine.com are in the STL format. Let’s start by clicking on the Load button in Cura. 2. When you have loaded a file into Cura you might notice the progress bar. Cura is automatically making the 3D model print ready for you. 3. In the meantime you can adjust settings and select a print type. 4. When the 3D model is prepared, the Save tool path button shows up and gives you the option to save the prepared model in a directory. Underneath the button Cura gives you an indication about your print on Estimated Print Time Amount of material required And the weight of your

• aakar AAKARv2, Changing Tool head 1. Two mounting guides are provided on every tool head compatible with your Aakar v2 that are used to mount and unmounts the tool head. 2. Use Hex wrench to unscrew the mounting bolts single turn in anti-clockwise direction is sufficient. Mounting guides

• aakar AAKARv2, 3. When connected Aakar v2 directly to PC you need to edit the config file on SD card and set static IP to your Aakar v2 as DHCP is not available. Edit lines 308, 309, 310 Follow above step 2 after editing.

• CURA SOFTWARE INTERFACE This is the main screen of Cura. Here you can choose which object or objects to print. And how you want them to be printed. 1. Load file Click this button to load an object to your print area. You can add as many objects as you can fit on the plate. 2. Save tool path (SD) When you press this button the prepared tool path will be saved on the SD ca

• WORKING TABLE (BED CALIBRATION) If the build plate is too far away from the nozzle your 3D-print might not stick to the build plate. Equally, if you adjust the build plate too close to the nozzle, the build plate can block the filament from extruding from the nozzle. It can also scratch the build plate. !!! The machine always comes as calibrated. No calibration is usually necessar

• aakar AAKARv2, 3 options to choose a print profile, higher quality prints are printer with mode resolution and hence require more time. 6. Print with support structure The option to give your model some support material to make the print more successful. 7. View modes After your model has been prepared for printing, you can use different view modes to analyze your design. 8. Rotate model options Option to change the rotation of the object you like to print. 9. Scale model options Option to change the scale of the object you like to print. 10. Mirror model option

• aakar AAKARv2, PRINTER CONNECTION POWER CONNECTION: Plug in the supplied power chord in the back panel of Aakar v2 Put the back panel switch to ON position to power on the machine. !!! Use only supplied power chord or any equivalent rating !!! Make sure power socket is properly earthed. Use of unearthed sockets may result in electrical shock to user and may permanently damage your Aakar v2

• aakar AAKARv2, Dear Customer, Thank you for purchasing the Aakar v2. This user manual will guide you through the setup and printing process step by step. Available online : www.aakar3dp.in Happy printing. Team Aakar Support We would love to hear from you. We are easy to reach and enjoy answering all your questions. Technical assistance, sales enquiries or general information, we are there for you. Find the information below to contact us. Support: [email protected] Sales: [email protected] Meet us onlin

Related Products and Documents (3D Printers):

Comparable Devices:

Similar Resources:

• Ender 3 Series (12 pages) Ender 3 Series 3D PrinterQuick Start Guide◆ ThisguideisfortheEnder3Seriesof3Dprinters.◆ Selectthecorrectinputvoltagetomatchyourlocalmains(220Vor110V)◆ Becauseofsoftware/hardwareupgradesandmodeldifferences,newrevisionsmaynotbelistedinthisgui …

• Rokit AEP Series (45 pages) AEP-CHS-20191117 1 AEP SERIES USER MANUAL …

• Geeetech Prusa I3 M201 (17 pages) Skip to contentManuals+User Manuals Simplified.GEEETECH Prusa Desktop 3D Printer Instruction ManualHome » Geeetech » GEEETECH Prusa Desktop 3D Printer Instruction Manual GEEETECH Prusa Desktop 3D Printer Instruction Manual …

• VP-Systems Resin Heater (6 pages) Resin Heater User GuideVersion 1.0© 2020 VP-Systems. All rights reserved.Rights to change the instructions or the product reserved. Some parts may look different than in the pictures.Contents of the packageHeater frame with controllerAC/DC Power adaptor (110V/220V -> 12V / ~60W)*Power cable (110/220V)*Power extension cable with 5.2mm plug and jack on bot …

• Felix Storch 3.2 (41 pages) Assembly Manual 16 December 2021 Revision 02 FELIX 3.2 www.felixprinters.com [email protected] Zeemanlaan 15 3401 MV IJsselstein The Netherlands …

• 3D Systems ProJet MJP 5600 (17 pages) Facility Requirements Guide ProJet® MJP 5600Facility Requirements GuideRev D Original InstructionsPlease refer back tohttp://infocenter.3dsystems.com/projetmjp5600/facility-requirements-guide for themost up-to-date Facility Requirements GuideAbout this manualThis document includes all of the overall facility requirements that will be needed to have a succe …

Comments, Questions and Opinions: