AAxeon MSC-102B Installation Manual
|
AAxeon MSC-102B, RS-422/485 Multiport Serial PCI Card Contents 1. Introduction ........................................................................ 1 2. Package Check List .......................................................... 2 3. Board Layouts and Connectors ....................................... 3 3.1 2S with DB9 Male Connectors ........................................... 3 3.1.1 JP5: UART Input Clock Speed Selector .....................3 3.1.2 JP1: RS-422/485 Mode Selector ...........
AAxeon MSC-102B, RS-422/485 Multiport Serial PCI Card 1 1. Introduction Congratulation on your purchasing this high performance RS-422/485 multiport serial PCI card. The card is high speed PCI bus based and plug-and-play compliant. It works at 2-wire (with Auto Transceiver Turn Around feature, ATTA TM ) and 4-wire configuration. Its UARTs are fully 16C950 (128-byte FIFO) featured and compatible with most of the serial devices available from the market. Features: Fully PCI Bus Specifications 2.2 and Power Management 1.0 compliant 128-byte on-chip FIFO and arbitrary trigger levels and interrupts, and automatic hardware
AAxeon MSC-102B, RS-422/485 Multiport Serial PCI Card 2 2. Package Check List Before installing the RS-422/485 multiport serial PCI card to your computer, please make sure the following accessories are well packed in the box: □ Multiport serial PCI Card x 1 □ Optional Octopus-Cable (only for 4-port and 8-port models) □ Driver CD × 1 □ Installation Guide × 1 (Mark the check box to help you check it)
AAxeon MSC-102B, RS-422/485 Multiport Serial PCI Card 3 3. Board Layouts and Connectors 3.1 2S with DB9 Male Connectors 3.1.1 JP5: UART Input Clock Speed Selector HI LOW J2: S1 JP7: S1 Terminator Enable/Disable J3: S2 JP8: S2 Terminator Enable/Disable JP1: RS-422/485 Mode Selector JP5: UART Clock Speed Selector UART Input Clock Speed = 1.8432MHZ, the maximum baud rate is 115.2Kbps (Default) HI LOW UART Input Clock Speed = 14.7456MHZ, the maximum baud rate is 926.1Kbps. In this setting, you need go to Windows’ COM port Properties to detect this input clock automatically and fit this
AAxeon MSC-102B, RS-422/485 Multiport Serial PCI Card 4 3.1.2 JP1: RS-422/485 Mode Selector Mode Settings for both S1 and S2 (JP1): Jumper Name Jumper Positions Mode and Termination Resistor Setting 485/422 485 (Default) 2-wire RS-485 mode 422 4-wire RS-422 mode RTS/AUTO RTS RS-485 Transmitter Buffer Enable is Controlled by RTS (active high) AUTO (Default) RS-485 Transmitter Buffer is controlled automatically by ATTA TM hardware circuit ECHO/NO_ECHO ECHO Transmitting data will be ec
RS-422/485 Multiport Serial PCI Card 5 S1 and S2 have its own setting. You need to go to each port to turn on both settings. 3.1.3 S1,S2 Connector Pin Assignments 3.1.4 S1,S2 Terminator Settings S1 Terminator Settings (JP7): Jumper Name Jumper Settings Termination Resistor Setting JP7 (TXD) IN TXD Terminato
AAxeon MSC-102B, RS-422/485 Multiport Serial PCI Card 6 Note: IN : Jumper Installed OUT : Jumper Not Installed S2 Terminator Settings (JP8): Jumper Name Jumper Settings Termination Resistor Setting JP8 (TXD) IN TXD Terminator Enabled OUT (Default) TXD Terminator Disabled JP8 (RXD) IN (Default) RXD Terminator Enabled OUT RXD Terminator Disabled JP8 (RTS) IN RTS Terminator Enabled OUT (Default) RTS Terminator Disabled JP8 (CTS) IN (Default) CTS Terminator Enable
AAxeon MSC-102B, RS-422/485 Multiport Serial PCI Card 7 3.2.1 JP5: UART Input Clock Speed Selector 3.2.2 JP1: RS-422/485 Mode Selector Mode Settings for both S1 and S2 (JP1): Jumper Name Jumper Positions Mode and Termination Resistor Setting 485/422 485 (Default) 2-wire RS-485 mode 422 4-wire RS-422 mode RTS/AUTO RTS RS-485 Transmitter Buffer Enable is Controlled by RTS (active high) AUTO (Default) RS-485 Transmitter Buffer is controlled automatically by ATTA TM hardware circuit 422 AUTO NO_ECHO NO_LOOP 485 RTS ECHO LOOP HI LOW UART Input Clock S
AAxeon MSC-102B, RS-422/485 Multiport Serial PCI Card 8 ECHO/NO_ECHO ECHO Transmitting data will be echoed back NO_ECHO (Default) No echo data LOOP/NO_LOOP LOOP RTS will be connected to CTS NO_LOOP (Default) RTS and CTS operate normally Please note that if the mode were set at “422” mode, the other settings (AUTO, ECHO and LOOP settings) will take no effect. The Echo mode is useful for the application program to detect if the RS-485 bus were in a collision. If the echoed data was not equal to the transmitted data, then the bus was in a collision. If you
AAxeon MSC-102B, RS-422/485 Multiport Serial PCI Card 9 S1 Terminator Settings (JP7): Jumper Name Jumper Settings Termination Resistor Setting JP7 (TXD) IN TXD Terminator Enabled OUT (Default) TXD Terminator Disabled JP7 (RXD) IN (Default) RXD Terminator Enabled OUT RXD Terminator Disabled Note: IN : Jumper Installed OUT : Jumper Not Installed S2 Terminator Settings (JP8): Jumper Name Jumper Settings Termination Resistor Setting JP8 (TXD) IN TXD Terminator Enabled OUT (Default) TXD Terminator Disabled
AAxeon MSC-102B, RS-422/485 Multiport Serial PCI Card 10 4. Installing the RS-422/485 PCI Card 1. Turn the system power OFF before installation! 2. Use static electricity discharge precautions. 3. Remove the chassis cover from your computer 4. Locate an unused PCI slot (typically white or ivory) and remove the corresponding slot cover from computer chassis. 5. Plug the RS-422/485 PCI card to the unused PCI expansion slot and attached the I/O card bracket to the computer chassis screw. 6. If your card’s connectors are terminal blocks, please install the terminal blocks from the outside of the computer. (Sin
AAxeon MSC-102B, RS-422/485 Multiport Serial PCI Card 11 5. Installing Drivers The RS-422/485 PCI card is plug-and-play so the driver installation is quite straightforward. Please “Browse” to the correct path on the Driver CD when Windows asking for the driver’s location. 5.1 Windows 98, ME, 2000, XP, 2003 When Windows start-up, OS will display Found New Hardware Wizard. Click〝 Next 〞to continue. 1. Insert Driver CD into the CD/DVD-ROM drive(for example D:), select〝 Search for a su
AAxeon MSC-102B, RS-422/485 Multiport Serial PCI Card 12 5.2 Windows NT 4.0 Since the Windows NT is not plug and play, you need to double click the following icon in the D:\IO\OXFORD\WinNT4 folder or run the Install_serial.exe in the same folder.
AAxeon MSC-102B, RS-422/485 Multiport Serial PCI Card 13 6. Set RS-485 in 2-wire (Half Duplex) Mode To enable your card to work in the RS-485 2-wire mode, please follow the following steps: 1. Set the Mode Jumpers (JP1) to “485” and “AUTO” as mentioned in the above sections. 2. Proceed with the following settings in Windows Right click on 〝 My Computer 〞 and choose 〝 properties 〞 (Win98,ME) or 〝 Manage 〞 (Win2000,XP) Choose 〝 Device Mana
AAxeon MSC-102B, RS-422/485 Multiport Serial PCI Card 14 Double click on 〝 PCI Communications Port (COM3) 〞 or 〝 PCI Communications Port (COM4) 〞 then select 〝 Settings 〞 6.1 Windows 2000, XP Go the the COM3’s properties and set the mode to “RS422/485” Choose RS485 buffer enable to “Active High” Set the other port (e.g. COM4) by the same procedures mentioned. Set〝 RS422/485 〞 and Active High 〞 for
RS-422/485 Multiport Serial PCI Card 15 6.2 Windows 98, ME In this examples, if the first port is COM5 and the second port is COM6, go to the COM5’s “properties” and select “RS485 Buf En Active high” for the DTR function Repeat the mentioned procedures to set the other port (e.g. COM6) Select〝 RS485 Buf_En Active high 〞for DTR function
RS-422/485 Multiport Serial PCI Card 16 7. Set High Baud Rate The RS-422/485 card was shipped at the low baud rate (115.2Kbps maximum). To set to high baud rate to 921.6Kbps maximum, 2 steps are required: Change the UART input clock jumper (JP5) to “HI” Go to the COM port’s settings of Windows’ Device Manager to let it detect the clock sp
AAxeon MSC-102B, RS-422/485 Multiport Serial PCI Card 17 7.2 Windows 98/ME Set the JP5 to “HI” In the Windows COM port properties as the following figure, select 〝 Data rate 〞 and click on 〝 Automatic Crystal Detection 〞 The 〝 Crystal Frequency 〞 settings will be set to 〝 14.7456MHZ 〝 , then click 〝 OK 〞 The settings will be saved by Windows. You don’t need to configure it again whenever you restart the system
AAxeon MSC-102B, RS-422/485 Multiport Serial PCI Card 19 8. Application Wiring 8.1 RS-485 (Transmitter is controlled automatically by ATTA TM Hardware) Please note that the RS-422/485 PCI Card supports optional auto echo mode. If enabled, when the data was sent to the RS-485 transmitter, the exact data will be sent back to its receiver simultaneously. The application program can use the echoed data to check if the RS-485 bus was currently in collission condition and need to be resent TXD+(485) TXD-(485) DATA(+) DATA(-) 2-wire twisted pair cable RS-422/485 PCI Card RS-485 Device
AAxeon MSC-102B, RS-422/485 Multiport Serial PCI Card 20 8.2 RS-422 (Transmitter buffer is always enabled) Please note that the RS-422/485 PCI Card supports 4-wire RS-422 mode. In this mode, the data was sent and received independently. So you need to connect them with the cross-over, twisted pair cable. For the model with DB9 connectors, it also provides two handshaking signials RTS+/RTS- and CTS+/CTS- to do the hardware flow control. In this case, the wiring will be as follows: RS-422/485 PCI Card TXD+ TXD-
rtd VID31460ER PCI Card Operation & user’s manual
VID31460ER |
ADS Technologies DLX 180 PCI Card Install manual
DLX 180 |
Belkin F5U508 PCI Card Operation & user’s manual
F5U508 |
LaCie FireWire 800 PCI Card Quick install manual
FireWire 800 |
YASKAWA NX100 PCI Card Operator's manual
NX100 |
Linksys WMP54G PCI Card Operation & user’s manual
WMP54G |
Transition Networks N-TGE-SFP-01 PCI Card Operation & user’s manual
N-TGE-SFP-01 |
Moxa Technologies CP-102E PCI Card Quick installation manual
CP-102E |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Philips | 579924816 | Operation & user’s manual | philips/579924816-546.pdf | 26 Oct 2023 | 8 | 1.53 Mb |
2 | Craftsman | 358.745460 | Operator's manual | craftsman/358-745460-68O.pdf | 08 Mar 2024 | 15 | 0.54 Mb |
3 | Acnodes | RM 6210 | Operation & user’s manual | acnodes/rm-6210-23N.pdf | 05 Jun 2023 | 14 | 0.41 Mb |
4 | Asus | Crosshair V Formula-Z | Operation & user’s manual | asus/crosshair-v-formula-z-6I7.pdf | 15 Nov 2023 | 190 | 9.38 Mb |
5 | Home Master | GDR02 | Operator's manual | home-master/gdr02-O28.pdf | 28 Jan 2023 | 47 | |
6 | Yamaha | RX-11 | Owner's manual | yamaha/rx-11-79W.pdf | 01 Jun 2023 | 36 | 2.35 Mb |
ClearClick
1 User’s Manual & Quick Start Guide 2-Year Warranty & USA-Based Tech Support For tech support, email us at: [email protected] Extend your warranty to 3 years for free by registering at: www.clearclicksoftware.com/Register/ www.ClearClick.tech
…
HD Capture Box Platinum Edition(28 pages) |
Vox Technologies
Installing LAN Drivers for Windows 98 Follow these steps to install the Intel 82559 LAN/Ethernet driver for Windows 95: 1. From the Control Panel, double-click the System icon. 2. Click the Device Manager tab. 3. Double-click Other Devices or Network Adapters in the list area. 4. Double-click a PCI Ethernet Controller. 5. Click the Driver tab, then c …
IBD69(6 pages) |
TP-Link
Hardware Connection1Quick Installation Guide450Mbps Wireless N Dual Band PCI Express AdapterMODEL NO. TL-WDN48007106504041For Windows VistaFor Windows XPYou may see the Found New Hardware Wizard after the adapter has been inserted. Please click ‘Cancel’.Package ContentsSystem Requirement· Windows 7 · Windows Vista · Wi …
TL-WDN4800(2 pages) |
Encore
10/100 Fast Ethernet CardBus Adapter User Manual Ver. 2.00 All brand names and trademarks are properties of their Respective owners. Jan/07 MN7000000015 1
…
ENP832-TX-RE(6 pages) |
Winnov
Videum 1000 Plus FamilyAudio and/or Video Capture CardsQuickStart GuideProduct Description page 2Scope of Delivery page 2System Requirements page 3Videum 1000 Plus Family Boards page 3Connector Descriptions page 4Safety Instructions page 5Getting Set Up page 5Installing Videum page 5Connecting Video Sources page 6Installing …
Videum 1000 Plus(10 pages) |
Conrad
Bestimmungsgemäße VerwendungDas Produkt ist zum Einbau in einen PCIe-Slot eines dafür geeigneten Computers vorgesehen und stellt dort zwei externe USB3.0-Ports und einen zwei interne SATA-Ports zur Verfügung.Die Sicherheitshinweise sind unbedingt zu befolgen!Eine andere Verwendung als zuvor beschrieben, führt zur Beschädigung dieses Produktes, darüber …
1333419(8 pages) |
Garmin Watch f?nix#S744SZ: f?nix Watch Owner's manual f?nix, 22 |
MUTOH Printer Rockhopper 3 ExtremeMUTOH Rockhopper 3 Extreme Printer Operation & user’s manual Rockhopper 3 Extreme, 137 |
Radio Shack Radio DX-398Radio Shack DX-398 Manual (Owner's manual), @4EQ2F7 DX-398, 48 |
Black Box Switch LGB2002A-R2LGB2002A-R2 (Switch ePDF Manual, #652T2X) LGB2002A-R2, 6 |
Sigma Digital Camera PHOTO PRO 2.5Sigma Product User Guide: PHOTO PRO 2.5 PDF Manual - J958KP PHOTO PRO 2.5, 43 |
Workzone Power Tool WMW 300-1Workzone Power Tool Operation & user’s manual (File: workzone-wmw-300-1-operation-user-s-manual-48, 30.08.2023) WMW 300-1, 48 |
GUARD1 GPS Duress DeviceGUARD1 Product Guide: Duress Device PDF Operation & user’s manual - QC92C6 Duress Device, 5 |
Zenoah Chainsaw G4100Zenoah Chainsaw Owner's manual (File: zenoah-g4100-chainsaw-56, Friday 26-01-2024) G4100, 56 |
Karcher Pressure Washer Electric Pressure Washer K 2.28Pressure Washer Operator's manual (Karcher Electric Pressure Washer K 2.28) Electric Pressure Washer K 2.28, 48 |
NTi NTi Stereo System Audio TalkBoxNTi NTi Audio TalkBox User Manual (Doc Type: Stereo System Operating manual) Audio TalkBox, 32 |
Canon Camcorder WFT-E6Camcorder #7RXOJ2 WFT-E6, 38 |
PROMETHEUS Kitchen Appliances Prome 303PROMETHEUS Product Guide: Prome 303 PDF Manual - N391OP Prome 303, 2 |