Nokia IP60 - Security Appliance Operation & User’s Manual

Text of Nokia IP60 - Security Appliance User Guide:

• Nokia IP60 - Security Appliance, Configuring Wireless Networks 202 Nokia IP60 Security Appliance User Guide Table 39: Basic Wireless Settings Fields In this field… Do this… Wireless Settings Network Name (SSID) Type the network name (SSID) that identifies your wireless network. This name will be visible to wireless stations passing near your access point, unless you enable the Hide the Network Name (SSID) option. It can be up to 32 alphanumeric characters long and is case-sensitive. Country Select the country where you are located. Warning: Choosing an incorrect country may result in the violation of gover

• Nokia IP60 - Security Appliance, Troubleshooting Wireless Connectivity 216 Nokia IP60 Security Appliance User Guide The IP60 appliance supports XR (Extended Range) technology. For best range, enable XR mode in the wireless network's advanced settings, and use XR-enabled stations. Range outdoors is normally much higher than indoors, depending on environmental conditions. Note: You can observe any changes in the wireless reception in the My Computers page. Make sure to refresh the page after making a change. Note: Professional companies are available for help in setting up reliable wireless networks,

• Nokia IP60 - Security Appliance, Configuring SNMP 434 Nokia IP60 Security Appliance User Guide The SNMP Configuration page appears. b. Complete the fields using the following table. If you selected the Send SNMP Traps check box, additional fields appear. 6. Click Apply. The SNMP configuration is saved. 7. Configure the SNMP clients with the SNMP community string.

• Using Diagnostic Tools Chapter 19: Maintenance 447 PARAMETERS element String. A filter string element. EXAMPLE The following filter string saves packets that either originate from IP address 192.168.10.1 or IP address 192.168.10.10: src 192.168.10.1 or src 192.168.10.10 port PURPOSE The port element captures all packets originating from or destined for a specific por

• Nokia IP60 - Security Appliance, Sample Implementation on Two Gateways 180 Nokia IP60 Security Appliance User Guide The High Availability page appears. c. Select the Gateway High Availability check box. The Gateway High Availability area is enabled. The LAN and DMZ networks are listed. d. Next to LAN, select the HA check box. e. In the LAN network's Virtual IP field, type the default gateway IP address 192.168.100.3. f. Next to DMZ, select the HA check box. g. In the DMZ network's Virtual IP field, type the defaul

• Nokia IP60 - Security Appliance, Using Diagnostic Tools Chapter 19: Maintenance 449 Note: When not prepended to other elements, the tcp element is the equivalent of ip proto tcp. SYNTAX tcp tcp element PARAMETERS element String. A port-related filter string element that should be restricted to saving only TCP packets. This can be the following: dst port - Capture all TCP packets destined for a specific port. port - Capture all TCP packets originating from or destined for a specific port. src port - Capture all TCP packets originating from a specific port.

• Nokia IP60 - Security Appliance, Controlling the Appliance via the Command Line Chapter 19: Maintenance 427 The Command Line page appears. 3. In the upper field, type a command. You can view a list of supported commands using the command help. For information on all commands, refer to the Nokia IP60 CLI Reference Guide. 4. Click Go. The command is implemented. Using the Serial Console You can connect a console to the IP60 appliance, and use the console to control the appliance via the command line. Note: Your terminal emulation software and your IP60 appliance's Serial port must be configured for the same speed. By default, the appliance's Serial

• Nokia IP60 - Security Appliance, Configuring VStream Antivirus Chapter 14: Using VStream Antivirus 315 The example below shows a Scan rule. 5. Complete the fields using the relevant information in the following table. 6. Click Next. The Step 3: Destination & Source dialog box appears. 7. To configure advanced settings, click Show Advanced Settings.

• Nokia IP60 - Security Appliance, Using Diagnostic Tools 444 Nokia IP60 Security Appliance User Guide SYNTAX dst destination PARAMETERS destination IP Address or String. The computer to which the packet is sent. This can be the following: An IP address A host name EXAMPLE The following filter string saves packets that are destined for the IP address 192.168.10.1: dst 192.168.10.1 dst port PURPOSE The dst port element captures all packets destined for a specific port. SYNTAX dst port port Note: This element can be prepended by tcp or udp. For information, see tcp on page 448 and udp on page 450. PARAMETERS port

• Nokia IP60 - Security Appliance, SmartDefense Categories Chapter 13: Using SmartDefense 283 Max Ping Size PING (ICMP echo request) is a program that uses ICMP protocol to check whether a remote machine is up. A request is sent by the client, and the server responds with a reply echoing the client's data. An attacker can echo the client with a large amount of data, causing a buffer overflow. You can protect against such attacks by limiting the allowed size for ICMP echo requests. Table 62: Max Ping Size Fields In this field… Do this… Action Specify what action to take when an ICMP echo response exceeds the Max Ping

• Using Internet Setup Chapter 5: Configuring the Internet Connection 93 In this field… Do this… Load Balancing Load Balancing Weight If you are using WAN load balancing, type a value indicating the amount of traffic that should be routed though this connection relative to the other connection. For example, if you assign the primary connection a weight

• Nokia IP60 - Security Appliance, Before You Install the Nokia IP60 Appliance 40 Nokia IP60 Security Appliance User Guide Windows Vista Checking the TCP/IP Installation 1. Click Start > Control Panel. The Control Panel window appears. 2. Under Network and Internet, click View network status and tasks. The Network Sharing Center screen appears. 3. In the Tasks pane, click Manage network connections.

• Nokia IP60 - Security Appliance, Adding and Editing VPN Sites 364 Nokia IP60 Security Appliance User Guide If you selected Try to Connect to the VPN Gateway, the Connecting… screen appears, and then the Contacting VPN Site screen appears. The Site Name dialog box appears. 3. Enter a name for the VPN site. You may choose any name. 4. Click Next. The VPN Site Created screen appears. 5. Click Finish. The VPN Sites page reappears. If you added a VPN site, the new site appears in the VPN Sites list. If you edited a VPN site, the modifications are reflected in the VPN Sites list.

• Nokia IP60 - Security Appliance, Using Rules 240 Nokia IP60 Security Appliance User Guide Rule Description Allow This rule type enables you to do the following: Permit outgoing access from your internal network to a specific service on the Internet. Permit incoming access from the Internet to a specific service in your internal network. Assign traffic to a QoS class. If Traffic Shaper is enabled for the direction of traffic specified in the rule (incoming or outgoing), then Traffic Shaper will handle relevant connections as specified in the bandwidth policy for the selected QoS class. For example, if Traffic Shaper is enabled for outgoing traffic, and you create an

• Logging on to the Nokia IP60 Portal 60 Nokia IP60 Security Appliance User Guide The Nokia IP60 Setup Wizard opens, with the Welcome page displayed. 4. Configure your Internet connection using one of the following ways: Internet Wizard The Internet Wizard is the first part of the Setup Wizard, and it takes you through basic Internet connection setup, step by step. For i

• Nokia IP60 - Security Appliance, Adding Internal Networks to Bridges 166 Nokia IP60 Security Appliance User Guide If the assigned bridge uses STP, additional fields appear. 5. Click Apply. A warning message appears. 6. Click OK. A success message appears. In the My Network page, the internal network appears indented under the bridge.

• Nokia IP60 - Security Appliance, Configuring SNMP Chapter 19: Maintenance 433 Note: Configuring SNMP is equivalent to creating a simple Allow rule, where the destination is This Gateway. To create more complex rules for SNMP, such as allowing SNMP connections from multiple IP address ranges, define Allow rules for the relevant port (by default, TCP port 161), with the destination This Gateway. For information, see Using Rules on page 238. To configure SNMP 1. Click Setup in the main menu, and click the Management tab. The Management page appears. 2. Specify from where SNMP access should be granted. See Access Options

• Overview Chapter 8: Configuring High Availability 173 Chapter 8 This chapter describes how to configure High Availability (HA) for two or more IP60 appliances. This chapter includes the following topics: Overview .................................................................................................. 173 Configuring High Availability on a Gateway .............

• Nokia IP60 - Security Appliance, SmartDefense Categories 306 Nokia IP60 Security Appliance User Guide In this field… Do this… Block proprietary protocols on all ports Specify whether proprietary protocols should be blocked on all ports, by selecting one of the following: Block. Block the proprietary protocol on all ports. This in effect prevents all communication using this peer-to-peer application. This is the default. None. Do not block the proprietary protocol on all ports. Block masquerading over HTTP protocol Specify whether to block using the peer-to

• Nokia IP60 - Security Appliance, Email Filtering Chapter 15: SMART Management and Subscription Services 339 Configuring Email Filtering Advanced Settings Note: If the IP60 appliance is remotely managed, contact your Service Center administrator to change these settings. To configure Email Filtering advanced settings 1. Click Services in the main menu, and click the Email Filtering tab. The Email Filtering page appears. 2. Next to the Bypass scanning if Service Center is unavailable option, specify how the gateway should handle Email Filtering when the service is enabled and the Service Center is unavailable, by doing do o

• Nokia IP60 - Security Appliance, Nokia IP60 and Nokia IP60 Wireless Installation 50 Nokia IP60 Security Appliance User Guide Nokia IP60 and Nokia IP60 Wireless Installation Installing the Nokia IP60 Appliance To install the IP60 appliance 1. Verify that you have the correct cable type. For information, see Network Requirements on page 26. 2. Connect the LAN cable: a. Connect one end of the Ethernet cable to one of the appliance's LAN ports. b. Connect the other end to PCs, hubs, or other network devices. 3. Connect the

• Nokia IP60 - Security Appliance, Configuring Wireless Networks Chapter 10: Working with Wireless Networks 203 In this field… Do this… Each operation mode indicates a wireless protocol (such as 802.11g Super), followed by the maximum bandwidth (such as 108 Mbps). The list of modes is dependent on the selected country. You can prevent older wireless stations from slowing down your network, by choosing an operation mode that restricts access to newer wireless stations. Note: The actual data transfer speed is usually significantly lower than the maximum theoretical bandwidth and degrades with distance. Important: The station wireless cards must support the selected ope

• Technical Specifications 478 Nokia IP60 Security Appliance User Guide Retail Box Dimensions (width x height x depth) 290 x 250 x 80 mm (11.42 x 9.84 x 3.15 inches) 290 x 250 x 80 mm (11.42 x 9.84 x 3.15 inches) 5V Power Supply Unit Power Supply Nominal Input In: 100~240VAC @ 0.5A In: 100~240VAC @ 0.5A Power Supply Nominal Output 9VAC @ 1.5 A OR: 12V

• Nokia IP60 - Security Appliance, Setting Up Your Nokia IP60 Appliance as a VPN Server 356 Nokia IP60 Security Appliance User Guide The Public Network dialog box appears. 12. Choose Do not dial the initial connection. 13. Click Next. The VPN Server Selection dialog box appears. 14. In the field, type the IP60 appliance's IP address. The Completing the New Connection Wizard screen appears. 15. Click Finish. 16. In the Network and Dial-up Connections window, right-click on the L2TP connection, and click Properties in the popup menu. The connection's Properties dialog box opens.

• Nokia IP60 - Security Appliance, Adding and Editing VPN Sites Chapter 16: Working with VPNs 379 The Site Name dialog box appears. 5. Enter a name for the VPN site. You may choose any name. 6. To keep the tunnel to the VPN site alive even if there is no network traffic between the IP60 appliance and the VPN site, select Keep this site alive. 7. Click Next. If you selected Keep this site alive, and previously you chose Download Configuration, the "Keep Alive" Configuration dialog box appears. Do the following: 1) Type up to three IP addresses which the IP60 appliance should ping in order to keep the tunnel to the VPN site alive. 2) Click Next. The VPN Site

• Nokia IP60 - Security Appliance, SmartDefense Categories 298 Nokia IP60 Security Appliance User Guide This provides a second layer of protection against FTP bounce attacks, by preventing such attacks from reaching well-known ports. Table 76: Block Known Ports Fields In this field… Do this… Action Specify what action to take when the FTP server attempts to connect to a well-known port, by selecting one of the following: Block. Block the connection. None. No action. This is the default.

More Instructions:

Nokia IP60 - Security Appliance Quick setup manual 23-11-2022 2

DOWNLOAD

Related Products and Documents (Security System):

Comparable Devices:

Similar Resources:

• Lorex LW2300 SERIES (2 pages) www.lorextechnology.comLW2300 Series Quick Start Guide_R2 Page 1Mount camera stand to the wall.NOTE: Wireless cameras require a power source to operate.NOTE: Before you install a camera, carefully plan where and how it will be positioned, and where you will route the cable that connects the camera to the power adaptor. Before starting permanent installation, …

• HIKVISION Pyronix Euro Mini (2 pages) 1 - Whilst in unset/day mode.2 - Enter your code/present a valid tag.3 - Select the Area (A, B, C or D) to set.4 - Exit the building.1 - Whilst the EURO mini is set.2 - Walk into the premises.3 - Enter your code/present a valid tag.4 - The EURO mini will be unset.Unset the EURO miniIf a warning appears on the display:- Press the ‘NO’ key.- Resolve the is …

• NAPCO MAGNUM ALERT RP1016E KEYPAD (16 pages)   …

• Crime Guard CG 745i (16 pages) Page PageL I M I T E D L I F E T I M E W A R R A N T YProducts manufactured and sold by OMEGA RESEARCH & DEVELOPMENT, INC. (the"Company"), are warranted to be free from defects in materials and workmanship under normaluse. If a product sold by the Company proves to be defective, the Company will repair or replaceit free of charge withi …

• ADEMCO TI110B1 (18 pages) 1TI110B1 GSM/PSTN Dual Network Burglar Alarm System .OverviewⅠ TI110B1 GSM/PSTN Dual Network Burglar Alarm System is ADEMCO compatibility alarm system, which adopts the advanced security technology, American-originated chipsets and siemens industrial-grade GSM module. And it boasts its dual networks to send alarm information out. When something wrong …

• Audiovox APS-510C (12 pages) 128-88051 of 12Page 1Model APS-510COwner’s Manual5 Button Remote Security Systemwith Dual Stage Shock SensorIMPORTANT! In order to provide the highest possible level of security to your vehicle, thissystem is equipped with selectable manual override circuitry. It is possible that you will needto manually override your security system if the transmitter …

Comments, Questions and Opinions: