Manualios.com

Panasonic AYRP500 Installation Manual

Panasonic AYRP500 Manual Online:

4.65, 953 votes
Panasonic AYRP500 User Manual
Panasonic AYRP500 User Guide
Panasonic AYRP500 Online Manual

Text of Panasonic AYRP500 User Guide:

  • Panasonic AYRP500, 1 The AY-RP500 Nonlinear Editing System is a combination of powerful hardware, flexible software and a custom human interface; developed for professional post-pro- duction. With the AY-RP500 Nonlinear Editing System, nonlinear editing is a creative process that finishes your videos to high standards while maintaining production budgets. PREFACE FEATURES • Simultaneous playback of two channels This system can playback video on two channels, with excellent image quality. • DVCPRO system The DVCPRO system is used for video compression and decompression. • A user interface suited for video producti

  • 38 ■ Turning on the power switches 1. Turn on the power switches on the peripheral equip- ment first. If using an external hard disk unit, turn on the power switch on the hard disk unit. The power indicator of the hard disk box lights red. 2. Turn on the power switch on the computer. Windows NT starts up. ■ Turning off the power switches Note: Before turning off the power, be ce

  • Panasonic AYRP500, 37 ANALOG Y/C VIDEO OUT DIGITAL VIDEO OUT DIGITAL AUDIO OUT L AUDIO OUT R AUDIO OUT DIGITAL VIDEO IN DIGITAL AUDIO IN ANALOG COMPOSITE VIDEO OUT LTC OUT LTC IN REF IN ■ Connecting the VCR (Serial Digital Interface : SDI) ● When connecting a video cassette recorder designed for commercial applications As in the figure below, [Genlock Input Control] is set to "Disable". [TAPE/EE switch] is set to "TAPE" in VCR. RS422 LTC/REF LR TARGA board JOG board LTC/REF cable RS422-1 RS422-2 Commercial VCR Video output monitor Speakers with

  • Panasonic AYRP500, 36 MEMO • Use a coaxial relay plug when connecting two coaxial cables (with BNC connectors) together. • When not using the REF OUT signal (loop-through) on the JOG board, turn off the 75Ω terminator switch on the JOG board; and connect the termination (accessory) to the REF OUT cable. • If a DVCPRO series VCR is used, the EE output from the VCR lags the input signal by about five frames. Coaxial relay plug REF OUT cable Termination ● S-VHS VCR (No RS422 control) Set [Genlock Input Control] to "Disabled". Video output monitor R AUDIO OUT L AUDIO OUT S-VIDEO OUT S VIDEO IN R AUDIO IN L AUDIO IN XLR3

  • 61 Video Performance S/N Ratio: More than 47 dB (Y/P B/PR, Y/C, Composite) Frequency Response: 5.0 MHz -3 dB (Y/P B/PR), 4.5 MHz -3 dB (Composite) Sampling Frequency: 13.5 MHz, 4:1:1, 8 bit component Compression: DVCPRO system Recording Time: Approx. 5 min / GB Audio Performance Dynamic Range More than 65 dB Total Harmonic Distortion Less than 0.2 % Frequency Response 20 kHz, ±

  • Panasonic AYRP500, 59 ● For a DELL PC mini tower type Pass the twist-tab wire through a hole of the guide rails as shown above. Use the twist-tab wire to secure the board spacer to the guide rails inside the computer. Twist the twist-tab wire and secure it properly. Check that the board spacer has been secured properly. Connect the ground wire to the computer's chassis only when the metal type of board spacer is supplied. (Refer to page 11) Insulating sheet SDI board Install the proper software for each type of the SDI board. Type 1 has no analog audio monitor Select it for installing "TARGA DV2

  • Panasonic AYRP500, 17 6. Appear Configuration menu window. Select "SCSI Device Configuration", and press [Enter] key. 7. Appear Device configuration window. In all SCSI ID (from #0 to #15) ,Change 40.0(from 20.0) at Maximum Sync Transfer Rate. At Each SCSI ID ,move cursor to 20.0 and press [Enter] key. Appear all useable number, select 40.0 and press [Enter] key. Please change about all SCSI ID. AHA-3940AU/AUW/AUWD at Bus:00h Device:0Eh Channel:A Configuration SCSI Bus Interface Definitions Host Adapter SCSI ID ......................7 SCSI Parity Checking .......................Enabled Host Adapter SCSI Termination .......Automatic Additional Options Boot Devi

  • Panasonic AYRP500, 39 To use the system, the application program on the CD- ROM supplied with the software package must be installed on the hard disk. This requires a keyboard, mouse, and personal computer monitor. ■ Setting Up the Virtual Memory This procedure sets up the virtual memory to operate the application program. DVEdit Setting Drive C: Initial Size 300MB Maximum Size 400MB Do not expand the virtual memory in a wrong drive. Otherwise it is not assured that the DVEdit works properly. 1. Open the Control Panel. 2. Double-click t

  • 29 23. The selected area will have the message "Unformatted". 24. In "Partition" on the menu bar, click "Commit Changes Now...". 25. At the message "Do you want to save changes?", click . 26. The message "Disks were updated successfully". Click . 27. The message of the unformatted area of the disk changes to "Unknown". 28. Cli

  • Panasonic AYRP500, 9. Follow the instructions to install the driver from the CD-ROM. Operate according to the procedures below. 1) The window for Truevision TARGA DV2000 Setup appears. Click . 2) The Product Type Inquiry window appears. Select the type of board to use, and click . For analog type, select "TARGA DV2000" (default). For SDI type, select "TARGA DV2000 SDX". ForSDI Voyager2,select "TARGA DV2000 SDX V2". (When the type is selected, is displayed.) Refer to Appendix (The type of the SDI board) about the type of the board. 3) The Choose Destination Location window apears. Click . 4) The Select Program Fold

  • Panasonic AYRP500, 40 4. Click C:. 5. Enter 300 in the box for initial size and 400 in the box for maximum size. 6. Click the button. Confirm that the top window shows 300-400. Then, click on this panel. 7. Click and restart. Yes OK Set

  • Panasonic AYRP500, 47 (b) Restart Select "Shutdown" from "Start". Add a check mark to "Restart Computer" and click . (c) Directory Delete If c:¥DVEdit and subsequent directories remain in Explorer after restart, delete all the files together with the directories. If e:¥audio, e:¥Title and subsequent directories remain, similarly delete all the files together with the directories. (The audio-storing drive characters may be different and there may be two or more audio/title storing drives depending on the case. In such a case, delete the above for all the drives.) 7. Installing new DVEdit Insert a CD-ROM into the CD-ROM drive

  • Panasonic AYRP500, 34 ■ Connecting the VCR Indicates an example of system connection. The system connection diagram shown below is intended as an example. The actual connection locations may differ depending on the model of computer used. ● When connecting a video cassette recorder designed for commercial applications As in the figure below, [Genlock Input Control] is set to "Blackburst Genlock Input" if [REF IN] is input to the TARGA board. For details on setup, read the "Special" section in the software manual. RS422 LTC/REF LR S-VIDEO OUT R-Y/R OUT B-Y/B OUT Y/G OUT R AUDIO OUT L

  • Panasonic AYRP500, 14 ■ Installing the SCSI board 1. Remove the cover for the PCI slot (the white connec- tor on the motherboard) that is adjacent to the slot where the TARGA DV2000 board is plugged in (on the side away from the CPU). 2. Carefully remove the SCSI board from its anti-static protective pack. If you need to set the board down, place it on top of this pack. 3. Plug the SCSI board into the PCI slot adjacent to the TARGA DV2000 board on the side away from the CPU, and secure the cover in place with the screws. 4. Store the screws and cover that were removed in a safe place. 5. For details on the cable connections, refer to the hard disk setup procedure. (Do not fail to conn

  • Panasonic AYRP500, 11 Insert the video compression board with board spacer attached. The rail guides on the personal computer Illustration of the video compression board inserted into PC 2.) Board spacer (plastic type) 4. Plug the TARGA DV2000 board into the PCI slot that is closest to the CPU (or the next closest slot, if the board will not physically fit into the closest slot, it is depends on the computer used). Here, firmly mount the board spacer between the guide rails on the per- sonal computer. The assembly diagram shown below is intended as an example. The actual con- nection locations may differ depending on the model of computer used. Connect the ground wire

  • Panasonic AYRP500, 16 ● When AHA-3940AUWD is the SCSI board used 1. Power On. 2. Appear next comment when Boot Up. Adaptec AHA-3940AU/AUW/AUWD SCSI BIOS v1.xx (c) 199x Adaptec, Inc. ALL Rights Reserved. <<< Press <Ctrl><A> for SCSISelect(TM)Utility! >>> 3. Quickly press [Ctrl]+[A] keys when appear this com- ment. 4. Run SCSI Utility and appear next window. Use arrow key, select Channel(A or B), and press [Enter] key. You must change configuration both Cannel Aand B. 5. Appear Menu window. Select "Configure/

  • Panasonic AYRP500, 18 ■ Installing the AY-RP500 board (JOG board) 1. Remove the cover from the ISA slot (the black con- nector on the motherboard) that is the farthest away from the CPU. 2. Carefully remove the AY-RP500 board (the JOG board) from its anti-static protective pack. If you need to set the board down, place it on top of this pack. 3. Use the jumper pins to set the IRQ and the I/O port. The permitted settings for the IRQ are 3, 4, 5, and 7; the permitted settings for the I/O port are 230H, 240H, 330H, and 340H. F

  • Panasonic AYRP500, 7 VGA loop cable (CA-206) Connects to the VGA connector on the video compression board. (15-pin male connector)(labelled "TARGA DV2000") Connects to the VGA connector on the computer. (15-pin male connector) (labelled "VGA") Connects to the cable for the personal computer monitor. (15-pin female connector) (labelled "MONITOR") Analog I/O cable (CA-208) Cable color Gray/white Red Blue Black Green Gray Black Gray/white Black Gray Black Green Blue Red Brown Black NO Q W E R T Y U I O P { } q w e r t Label S-VIDEO IN R-Y/R IN B-Y/B IN CV/CS IN Y/G IN R AUDIO IN L AUDIO IN S-VIDEO OUT L AUDIO OUT R AUDIO OUT CV/CS

  • 9 Install the boards in the computer. There are three boards to be installed: 1. Video compression board (TARGA DV2000 board) 2. SCSI board 3. JOG board [AY-RP500 board (JOG board)] ■ Preparation 1. Have a computer with Windows NT installed ready. Note: Windows NT must be installed on drive C: (IDE hard disk) which has been formatted using the NTFS file system. Note: Before installing Windo

  • Panasonic AYRP500, 49 (d) If the following message appears during uninstall, click . (e) Check disk scheduling Enter "chkdsk /f c:" on the command prompt panel. After that, You will be asked "Check disk scheduling(Y/N)?" So enter "y" on the command prompt panel. This executes the check-disk in restarting. (f) Restart. (The check-disk automatically runs at restart.) Select "Shutdown" from "Start". Add a check mark to "Restart Computer" and click . (g) Directory delete If c:¥TARGA2KDV and subsequent directories remain in Explorer after restart, delete all together with the directories. Yes No to All 5. Installing the New Targa Driver

  • Panasonic AYRP500, 22 3. Insert the hard disk, and attach it with screws (in four places). The assembly diagram shown below is intended as an example. The actual connection locations may differ depending on the model of computer used. When installing another hard disk unit, remove the expansion bay brackets, insert the hard disk, and then secure it in place with screws. then secure it in place with screws (in four places). (Refer to the dia- gram below). The assembly diagram shown below is intended as an example. The actual connection locations may differ depending on the model

  • Panasonic AYRP500, 25 ● When AHA-3940AUWD is the SCSI board used 1. Power On. 2. Appear next comment when Boot Up. Adaptec AHA-3940AU/AUW/AUWD SCSI BIOS v1.xx (c) 199x Adaptec, Inc. ALL Rights Reserved. <<< Press <Ctrl><A> for SCSISelect(TM)Utility! >>> 3. Quickly press [Ctrl]+[A] keys when appear this com- ment. 4. Run SCSI Utility and appear next window. Use arrow key, select Channel(A or B), and press [Enter] key. 5. Appear Menu window. Select "SCSI Disk Utilities", and press [Enter] key. Check the connected SCSI

  • Panasonic AYRP500, 56 ■ How to install the board Plug the AY-PB500 board (TARGA DV2000 board) into the PCI slot that is closest to the CPU (or the next closest slot, if the board will not physically fit into the closest slot). Here, firmly mount the board spacer between the guide rails on the computer. Screw down the cover (AY-PB500). Then use the twist-tab wire to secure the board spacer to the guide rails inside the computer. ● For a GATEWAY PC tower type APPENDIX Use the twist-tab wire to secure the board spacer to the guide rails inside the computer. Twist the twist-tab wire and secure it properly. C

  • Panasonic AYRP500, 26 6. Appear a list of the connected SCSI devices. (When ST34371W made by SEAGATE is connected to ID=1) If the devices actually connected are at variance with what is listed, a wrong connection, SCSI ID set- ting error, terminal setting error or defective hard disk may be to blame. Press [ESC] key to exit. First, check the connections and the SCSI ID and terminal settings. If the message remains, a defec- tive hard disk may be to blame. If what is listed matches with the devices actually connected, use the arrow keys to mo

  • Panasonic AYRP500, 27 ■ Setting up the hard disk It must be set up so that the hard disk can be used. 1. Turn on the power, and start up Windows NT. 2. Click . From Programs in the Start Menu, click "Administrative Tools" p ✂Disk Administrator". The program starts up. 3. When the Disk Administrator starts up, a list appears showing the bulk-storage devices such as hard disks and CD-ROM. 4. The contents displayed are as follows: Disk 0: Always the IDE drive. Disk 1 and after: SCSI hard disks connec

Related Products and Documents (Control Panel):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Asus A8N-VM-CSM Operation & user’s manual asus/a8n-vm-csm-W37.pdf 19 Oct 2023 76 3.08 Mb
2 K-array KA40 Operation & user’s manual k-array/ka40-R68.pdf 04 Feb 2024 8
3 TSL MDU12-PMi Operation & user’s manual tsl/mdu12-pmi-2A6.pdf 19 Feb 2023 29
4 Ford Escort Tracer1999 Workshop manual ford/escort-tracer1999-9X8.pdf 13 Oct 2022 10
5 Gigabyte GV-R96S128D Declaration of conformity gigabyte/gv-r96s128d-771.pdf 03 Nov 2022 40 2.76 Mb
6 Whistler WS1095 Owner's manual whistler/ws1095-5S5.pdf 25 Nov 2022 69

Similar Resources:

  • Amerec

    A6 Club Control

    (11 pages)
    A6 OPERATING INSTRUCTIONS05/12/16 4211-146 Page 1 of 11 Amerec’s A6 control for the AX steamer is a touch screen control intended to be mounted on a wall, generally in or near the steam bath. It may be mounted directly on the wall surface or, using an optional recessed mounting box, it may be mounted so its touch …
  • Tekmar

    Difference Setpoint Control 156

    (12 pages)
    1 of 12 © 2010 D 156 - 06/10D 15606/10- Data BrochureDifference Setpoint Control 156The Difference Setpoint Control 156 is designed to operate an on/off pump to transfer heat from a heat source to a storage tank. The control operates based on a setpoint temperature difference (T). The relay turns on when the T rises above the setpoint and turns …
  • Siemens

    SINUMERIK 840D sl

    (708 pages)
     Milling ___________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ SINUMERIK SINUMERIK …
  • HWH

    625 Series

    (19 pages)
    OPERATOR’S MANUALML38142/MP04.252810SEP09Touch Panel Leveling ControlBI-AXIS Hydraulic LevelingFEATURING:HWH CORPORATION(On I-80, Exit 267 South)2096 Moscow Road | Moscow, Iowa 52760Ph: 800/321-3494 (or) 563/724-3396 | Fax: 563/724-3408www.hwh.com625 SERIES LEVELING SYSTEMHWH COMPUTER-CONTROLLEDRStraight-Acting JacksAP38141RHWH COMPUTERIZED LEVELIN …
  • Feelsafe

    OMNI 3000

    (20 pages)
    0 tructions SEPT '86. F&Safe, Inc., 50 Engineers Road, Houppauge. New York 11788 (516) 5826161 (803) 6455430 Copyright @ ‘85 FeelSafe. Inc. Printed in U S.A.’ …
  • FBII

    OMNI-848

    (28 pages)
    ++DDUUGGZZLLUUHHGG::LLUUHHOOHHVVVV66\\VVWWHHPP220011,,8VHU*XLGHARMEDREADY1472580369#STAYBYPASSINSTANTCODEARMEDREADY1472580369#STAYBYPASSINSTANTCODE 1 324 657 98#0STAYINSTANTBYPASSCODEARMAC / LBREADYSTAYINSTLO BATTSPRV.N9939 8/00FIRE BURGLARY INSTRUMENTS, INC. …

Comments, Questions and Opinions: