Cisco SF220-24 Quick Start Manual

Text of Cisco SF220-24 User Guide:

• Cisco SF220-24, Quick Start Guide Cisco 220 Series Smart Plus Switches Package Contents • Cisco 220 Series Smart Plus Switch • Power Cord • Rack-Mount Kit and Rubber Feet • Console Cable • This Quick Start Guide • Product CD • Technical Support Contacts

• 2 Cisco 220 Series Smart Plus Switches Quick Start Guide Welcome Thank you for choosing the Cisco 220 Series Smart Plus Switch, a Cisco network communications device. This device is designed to be operational right out-of-the-box as a standard bridge. In the default configuration, it will forward packets between connecting devices after power up. This guide familiarizes y

• Cisco SF220-24, Cisco 220 Series Smart Plus Switches Quick Start Guide 3 Front Panel The ports, LEDs, and Reset button are located on the front panel of the switch. RJ-45 Ethernet Ports—The RJ-45 Ethernet ports connect network devices, such as computers, printers, and access points, to the switch. SFP Ports—The small form-factor pluggable (SFP) ports are connection points for modules so that the switch can link to other switches. These ports are also commonly referred to as mini Gigabit Interface Converter

• Cisco SF220-24, 4 Cisco 220 Series Smart Plus Switches Quick Start Guide Reset Button—The Reset button is used to reboot or reset the switch with a pin or paper clip. See Returning the Cisco 220 Switch to the Factory Default Settings for more information. System LED—(Green) Lights steady when the switch is powered on, and flashes green when booting, performing self-tests, and/or acquiring an IP address. If the LED flashes amber, the switch has detected a hardware failure, a firmware failure, and/or a configuration file error. Link/ACT LED—(Green) Located on the left o

• Cisco SF220-24, Cisco 220 Series Smart Plus Switches Quick Start Guide 5 Mounting the Cisco 220 Switch There are three ways to physically install the switch: • Place the switch on a flat surface. To place the switch on a desktop, install the four rubber feet (included) on the bottom of the switch. • Mount the switch in a standard rack (1 rack unit high). • Mount the switch to a wall (non-PoE models only). Placement Tips •Ambient Temperature—To prevent the switch from overheating, do not operate it in an area that exceeds an ambient temperature of 122°F (50°C). •Ai

• 6 Cisco 220 Series Smart Plus Switches Quick Start Guide S TEP 2 Repeat the previous step to attach the other bracket to the opposite side of the switch. STEP 3 After the brackets are securely attached, the switch is now ready to be installed into a standard 19-inch rack as shown here. Wall Mounting (Non-PoE Models Only) If your switch is the non-PoE model, you can wall-mount it by

• Cisco SF220-24, Cisco 220 Series Smart Plus Switches Quick Start Guide 7 To mount the non-PoE switch to the wall: STEP 1 Determine where you want to mount the switch. Verify that the surface is smooth, flat, dry, and sturdy. STEP 2 Attach one of the supplied brackets to one side of the switch and use two pan head M5 screws to secure it. STEP 3 Repeat the previous step to attach the other bracket to the opposite side of the switch. STEP 4 For the best support of the switch and cables, make sure that the switch is attached securely to wall studs or to a firmly attached plywood mounting backboard. Mount the switch with the front panel facing down as sho

• 8 Cisco 220 Series Smart Plus Switches Quick Start Guide Connecting Network Devices To connect your switch to the network: STEP 1 Connect an Ethernet cable to the Ethernet port of a computer, printer, network storage, or other network devices. STEP 2 Connect the other end of the Ethernet cable to one of the numbered Ethernet ports of the switch. The LED of the p

• Cisco SF220-24, Cisco 220 Series Smart Plus Switches Quick Start Guide 9 CAUTION Consider the following when connecting switches capable of supplying PoE: The PoE models of the switches are PSEs that are capable of supplying DC power to attaching PDs. These devices include VoIP phones, IP cameras, and wireless access points. The PoE switches can detect and supply power to pre-standard legacy PoE Power Devices. Due to the support of legacy PoE, it is possible that a PoE switch acting as a PSE may mistakenly detect and supply power to an attaching PSE, including other PoE switche

• Cisco SF220-24, 10 Cisco 220 Series Smart Plus Switches Quick Start Guide Configuring Your Switch Using the Web-based Interface To access the switch with a web-based interface, you must know the IP address that the switch is using. The default configuration of the switch is to use its factory default IP address of 192.168.1.254 until it has obtained an IP address from a DHCP server. NOTE If you are managing the switch through a network connection and the switch IP address is changed, either by a DHCP server or manually, your access to the switch will be lost. You must enter the new IP address that the switch is using into you

• Cisco SF220-24, Cisco 220 Series Smart Plus Switches Quick Start Guide 11 reconnect the devices for them to discover their new IP addresses from the DHCP server. NOTE Details on how to change the IP address on your computer depend upon the type of architecture and operating system that you are using. Use your computers local Help and Support functionality and search for “IP Addressing.” STEP 5 Open a web browser window. If you are prompted to install an Active-X plug-in when connecting to the device, follow the prompts to accept the plug-in. STEP 6 Enter the switch IP address in the address bar and press Enter. For example, http://19

• Cisco SF220-24, 12 Cisco 220 Series Smart Plus Switches Quick Start Guide Configuring Your Switch Using the Console Port To configure the switch using the console port: STEP 1 Connect a computer to the switch console port using the supplied console cable. STEP 2 Start a console port utility such as HyperTerminal on the computer. STEP 3 Configure the utility with the following parameters: • 9,600 bits per second • 8 data bits • no parity • 1 stop bit • no flow control STEP 4 Enter a username and password. The default username is cisco, and the default password is cisco. Usernames and passwords are both case sensitive. If this is th

• Cisco SF220-24, Cisco 220 Series Smart Plus Switches Quick Start Guide 13 Troubleshoot Your Connection If you cannot access your switch from the web-based interface, the switch may not be reachable from your computer. You can test network connections by using ping on a computer running Windows: STEP 1 Open a command window by selecting Start > Run and enter cmd. STEP 2 At the Command window prompt, enter ping and the switch IP address. For example, ping 192.168.1.254 (the default static IP address of the switch). If you can reach the switch, you should get a reply similar to the following: Pinging 192.168.1.254 with 32 bytes of data: Reply from 192.168.1.254:bytes=32 time<1ms TTL=

• Cisco SF220-24, 14 Cisco 220 Series Smart Plus Switches Quick Start Guide No IP route: If the switch and your computer are in different IP subnets, you need one or more routers to route the packets between the two subnets. Unusually long access time: Due to the standard spanning tree loop detection logic, adding new connections may take 30 to 60 seconds for the affected interfaces and/or LAN to become operational. Returning the Cisco 220 Switch to the Factory Default Settings • To reboot the switch, press and hold the Reset button for less than ten seconds. • To restore the switch to

• Cisco SF220-24, Cisco 220 Series Smart Plus Switches Quick Start Guide 15 Where to Go From Here WARNING This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Support Cisco Support Community www.cisco.com/go/smallbizsupport Cisco Support and Resources www.cisco.com/go/smallbizhelp Phone Support Contacts www.cisco.com/en/US/support/ tsd_cisco_small_business _support_center_contacts.html Cisco Firmware Downloads ww

• Cisco SF220-24, Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA www.cisco.com Small Business Support, Global: www.cisco.com/go/sbsc Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Ciscotrademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R) © 2014 Cisco Systems, Inc. All rights reserved. 7

More Instructions:

	Cisco SF220-24 Quick start manual 18-01-2024 2	DOWNLOAD
	Cisco SF220-24 Administration manual 27-07-2023 289	DOWNLOAD

Related Products and Documents (Switch):

Comparable Devices:

Similar Resources:

• Linkskey LKV-M02 (2 pages) Quick Installation Guide Applicable model: LKV-M02do not have to make any configuration before installation.LKV-M022-port Super Mini Desktop KVMSwitchw/ built-in 1.5M CablesQuick Installati on GuideIt’s a Plug-and-Play device: Just connect keyboard, monitorand mouse to the KVM Switch, and then connect the KVMcables to connectors on your computers, and then …

• Extron electronics YCS SW2 A (2 pages) Setup Guide — YCS SW2 AThe Extron® YCS SW2 A is a two input, dual output video and audio switcher with transcoding and auto-input switching capabilities and digital time base correction (TBC). This guide provides basic instructions for setting up and operating the switcher.InstallationStep 1 — Mount the unitMount the switcher on a rack shelf, furnitur …

• NETGEAR AXM762 - ProSafe 10 Gigabit (2 pages) )NSTALLATION'UIDEeProSafe 10 Gigabit Ethernet SFP+ Module AXM762Install Your Optical ModuleThe 10 Gigabit small form-factor pluggable (SFP+) module provides a full-duplex 10G bps each direction for Ethernet operation on NETGEAR managed switches.The switch will automatically detect the AXM762, so you can simply plug it into an available module slot. T …

• Static Power iSTS R (2 pages) 1Supply 1 InputPush-in terminal suits 4mm² cable, use a small blade type screwdriver in the top slot and press in; insert the cable and release. DO NOT USE FERRULES OR TWIST THE WIRE ON THE PUSH IN CONNECTORS.Repeat for the Neutral Conductor. Note the neutral is not fused. Bare the wire just 8mm.2Output TerminalPush-in terminal suits 4mm² cable, use a smal …

• TRENDnet TEG-S24Dg (7 pages) TEG-S24DgTEG-S24DgTEG-S24Dg (V2) /02.12.2014 RouterRouteurMаршрутизаторRoteadorRuuteriInternetInternetИнтернетInternetiQuick Installation GuideGuide d'installation rapideAnleitung zur SchnellinstallationGuía de instalación rápidaРуководство по быстрой установкeGuia de Instalação em PortuguêsEestikeel …

• Belkin F1U125-KIT (19 pages) Windows NT/2k/XPBefore you install the Belkin Bitronics software, you must first make sure that eachdevice works properly on its own with each computer.1. Check your BIOS and make sure that the printer port on your computers is set toECP mode.Note: Please consult your computers manufacture’s manual, tech support, orwebsite for information on how to set yo …

Comments, Questions and Opinions: