Cisco MDS9120 - MDS 9120 Multilayer Fabric Switch Installation Manual

Text of Cisco MDS9120 - MDS 9120 Multilayer Fabric Switch User Guide:

• Cisco MDS9120 - MDS 9120 Multilayer Fabric Switch, Send documentation comments to [email protected] 3-10 Cisco MDS 9100 Series Hardware Installation Guide OL-21514-01 Chapter 3 Connecting the Cisco MDS 9100 Series Connecting to a Fibre Channel Port

• Cisco MDS9120 - MDS 9120 Multilayer Fabric Switch, Send documentation comments to [email protected] C-5 Cisco MDS 9100 Series Hardware Installation Guide OL-21514-01 Appendix C Cable and Port Specifications Supported Power Cords and Plugs Note Only the standard power cords or jumper power cords provided with the switch are supported. Figure C-3 shows the supported plugs for the Cisco MDS 9100 Series power supplies. Figure C-3 300-W Power Supply Plugs 1 Argentina, IRAM 2073 plug (10 A) 5 Italy 1/3G plug, CEI 23-16 (10 A) 2 North America NEMA 5-15P plug (15 A) 6 United Kingdom BS89/13, BS 1363/A (13 A; replaceable fuse) 3 Australia, New Zealand

• Cisco MDS9120 - MDS 9120 Multilayer Fabric Switch, Send documentation comments to [email protected] 2-29 Cisco MDS 9100 Series Hardware Installation Guide OL-21514-01 Chapter 2 Installing the Cisco MDS 9100 Series Removing and Installing Components Removing and Installing AC Power Supplies This section provides instructions for removing and installing the AC power supplies for the Cisco MDS 9100 Series switches. Caution Power supplies for the Cisco 9100 Series switches look similar but they differ slightly. Be sure to use the cor

• Cisco MDS9120 - MDS 9120 Multilayer Fabric Switch, Send documentation comments to [email protected] 1-15 Cisco MDS 9100 Series Hardware Installation Guide OL-21514-01 Chapter 1 Product Overview Switch LEDs Figure 1-14 Cisco MDS 9140 Switch and Cisco MDS 9120 Switch LEDs Table 1-3 describes the front panel LEDs for the Cisco MDS 9100 Series. 1 Switch status LED 5 10/100 Ethernet management port activity LED 2 Power supply LED 6 Top port link LED 3 Fan module status LED 7 Bottom port link LED 4 10/100 Ethernet management port link LED 94181 3 4 5 6 7 1 2 Ta bl e 1-3 Switching Module LEDs LE

• Cisco MDS9120 - MDS 9120 Multilayer Fabric Switch, Send documentation comments to [email protected] 1-11 Cisco MDS 9100 Series Hardware Installation Guide OL-21514-01 Chapter 1 Product Overview Cisco MDS 9100 Series Ports All 32 4-Gbps ports and 2 10-Gbps ports can operate at line rate concurrently. In addition, the 10-Gbps ports can be activated independently at 24- or 32-port configurations. A 64-port switch can be formed out of Cisco two MDS 9134 Switches by using a copper CX4 X2 transceiver as an Inter-Switch Link (ISL). The Cisco MDS 9134 Switch includes hot-swappable SFP interfaces. All SFP interfaces are 1, 2, and 4 Gbp

• Cisco MDS9120 - MDS 9120 Multilayer Fabric Switch, Send documentation comments to [email protected] 2-35 Cisco MDS 9100 Series Hardware Installation Guide OL-21514-01 Chapter 2 Installing the Cisco MDS 9100 Series Removing and Installing Components Verifying the Fan Module To verify that the new fan module is installed correctly, follow these steps: Step 1 Listen for the fans; you should immediately hear them operating. If you do not hear them, ensure that the fan module is inserted completely in the switch and the faceplate is flush with the switch back panel. Step 2 Ve

• Cisco MDS9120 - MDS 9120 Multilayer Fabric Switch, Send documentation comments to [email protected] 1-5 Cisco MDS 9100 Series Hardware Installation Guide OL-21514-01 Chapter 1 Product Overview Cisco MDS 9100 Series Multilayer Fabric Switches Cisco MDS 9124 Switch The Cisco MDS 9124 Multilayer Fabric Switch has a total of 24 1-, 2-, and 4-Gbps autosensing Fibre Channel ports. The Cisco MDS 9124 Switch features On-Demand Port Licensing. You can activate licensing in 8-port increments with each on-demand port activation license for up to a

• Send documentation comments to [email protected] 8 Cisco MDS 9100 Series Hardware Installation Guide OL-21514-01 New and Changed Information Cisco MDS 9134 Switch overview Description of NPIV support. 3.2(2c) Product Overview chapter. Cisco MDS 9124 Switch overview Description of NPIV support. 3.2(2c) Product Overview chapter. Cisco MDS 9134 Switch overview Description and ill

• Cisco MDS9120 - MDS 9120 Multilayer Fabric Switch, Send documentation comments to [email protected] 2-7 Cisco MDS 9100 Series Hardware Installation Guide OL-21514-01 Chapter 2 Installing the Cisco MDS 9100 Series Installing the Switch in a Cabinet or Rack Figure 2-1 Front Rack-Mount Brackets and C Brackets Installed on the Cisco MDS 9100 Series Step 3 Install the slider rails in the rack. Position one of the slider rails against the rack mounting rails and align the screw holes as shown in Figure 2-2. If you are using the notched slider rails for the Cisco MDS 9134 or the Cisco MDS 9124 Switch, see Figure 2-3. Note Depending on when you purchased your Cisco MDS 9124 Switch, you may

• Cisco MDS9120 - MDS 9120 Multilayer Fabric Switch, Send documentation comments to [email protected] 2-2 Cisco MDS 9100 Series Hardware Installation Guide OL-21514-01 Chapter 2 Installing the Cisco MDS 9100 Series Preinstallation Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings t

• Cisco MDS9120 - MDS 9120 Multilayer Fabric Switch, Send documentation comments to [email protected] 1-10 Cisco MDS 9100 Series Hardware Installation Guide OL-21514-01 Chapter 1 Product Overview Cisco MDS 9100 Series Ports All 48 8-Gbps ports can operate at line rate concurrently. Ports on the Cisco MDS 9134 Switch The Cisco MDS 9134 Switch provides up to 32 autosensing and autonegotiating Fibre Channel ports capable of speeds of 1, 2, and 4 Gbps. The first 24 ports are licensed by default. On-Demand Port Activation Licensing allows expansion to 32 ports, with additional ports available as an 8-port group. The Cisco MDS 9134 Switch also offer

• Cisco MDS9120 - MDS 9120 Multilayer Fabric Switch, Send documentation comments to [email protected] 2-9 Cisco MDS 9100 Series Hardware Installation Guide OL-21514-01 Chapter 2 Installing the Cisco MDS 9100 Series Installing the Switch in a Cabinet or Rack Step 5 Insert the switch into the rack: a. By using both hands, position the switch with the back of the switch between the front rack-mounting rails as shown in Figure 2-4. If you are using the notched rails, for the Cisco MDS 9148 Switch, Cisco MDS 9134 Switch, or the Cisco MDS 9124 Switch, see Figure 2-5. b. Align the two C brackets on either side of the switch with the slider r

• Cisco MDS9120 - MDS 9120 Multilayer Fabric Switch, Send documentation comments to [email protected] 2-12 Cisco MDS 9100 Series Hardware Installation Guide OL-21514-01 Chapter 2 Installing the Cisco MDS 9100 Series Installing the Switch in a Cabinet with Insufficient Front Clearance the requirements described in Appendix A, “Cabinet and Rack Requirements,” except the cabinet has less than three-inch clearance between the inside of the front door or bezel panel and the front cabinet mounting rails. This rear-facing installation is necessary to ensure that the minimum bend radius for the fiber-

• Cisco MDS9120 - MDS 9120 Multilayer Fabric Switch, Send documentation comments to [email protected] 3-8 Cisco MDS 9100 Series Hardware Installation Guide OL-21514-01 Chapter 3 Connecting the Cisco MDS 9100 Series Connecting to a Fibre Channel Port Installing a Cable into an SFP Transceiver Caution To prevent possible damage to the cable or transceiver, install the transceiver in the port before installing the cable in the transceiver. To install a cable into a transceiver, follow these steps: Step 1 Attach an ESD-preventive wrist strap and follow its instructions for use. Step 2 Remove the dust cover from the

• Cisco MDS9120 - MDS 9120 Multilayer Fabric Switch, Send documentation comments to [email protected] 2-30 Cisco MDS 9100 Series Hardware Installation Guide OL-21514-01 Chapter 2 Installing the Cisco MDS 9100 Series Removing and Installing Components Step 2 Make sure the power cord is disconnected before installing the power supply. Step 3 Verify that the power switch is in the off (0) position on the power supply that you are installing. Step 4 Slide the power supply into the power supply bay. Make sure that the power supply is fully seat

• Cisco MDS9120 - MDS 9120 Multilayer Fabric Switch, Send documentation comments to [email protected] B-17 Cisco MDS 9100 Series Hardware Installation Guide OL-21514-01 Appendix B Technical Specifications X2 Transceiver Specifications X2 Transceiver Specifications The Cisco MDS 9134 Switch is compatible with X2 transceivers and cables that have SC connectors. Each transceiver must match the transceiver on the other end of the cable in terms of wavelength, and the cable must not exceed the stipulated cable length for reliable communications. Use only Cisco X2 transceivers with the Cisco

• Cisco MDS9120 - MDS 9120 Multilayer Fabric Switch, Send documentation comments to [email protected] A-5 Cisco MDS 9100 Series Hardware Installation Guide OL-21514-01 Appendix A Cabinet and Rack Installation Cisco MDS 9000 Family Telco and EIA Shelf Bracket Before Installing the Shelf Brackets Before installing the shelf brackets, inspect the contents of your kit. Table A-1 lists the contents of the shelf bracket kit. Required Equipment You need the following equipment for this installation: • Number 2 Phillips screwdriver • Tape measure and level (to ensure shelf brackets are level) Installing the Shelf Bracket Kit into a Two-Post Telco Rack Figure A-1 shows the installa

• Cisco MDS9120 - MDS 9120 Multilayer Fabric Switch, Send documentation comments to [email protected] 3-4 Cisco MDS 9100 Series Hardware Installation Guide OL-21514-01 Chapter 3 Connecting the Cisco MDS 9100 Series Connecting the 10/100 and 10/100/1000 Ethernet Management Port Connecting the 10/100 and 10/100/1000 Ethernet Management Port The autosensing 10/100 and 10/100/1000 Ethernet management port is located on the left side of the front panel (labeled 10/100/1000 MGMT), to the right of the Console port. This port is used for out-of-band management of the Cisco MDS 9100 Series switches. Note Currently, only the

• Send documentation comments to [email protected] 3-5 Cisco MDS 9100 Series Hardware Installation Guide OL-21514-01 Chapter 3 Connecting the Cisco MDS 9100 Series Connecting to a Fibre Channel Port • Maintaining SFP Transceivers and Fiber-Optic Cables, page 3-9 Removing and Installing SFP Transceivers Caution Removing and installing an SFP transceiver can s

• Cisco MDS9120 - MDS 9120 Multilayer Fabric Switch, Send documentation comments to [email protected] 2-28 Cisco MDS 9100 Series Hardware Installation Guide OL-21514-01 Chapter 2 Installing the Cisco MDS 9100 Series Removing and Installing Components Figure 2-22 Rear View of the Cisco MDS 9124 Switch For the Cisco MDS 9140 Switch and the Cisco MDS 9120 Switch, the fans should not be removed for prolonged periods of time during operation. If one fan module fails, a single healthy fan module can temporarily provide sufficient cooling to maintain switch operation under normal conditions, but the failed fan module should be replaced as soon as possi

• Send documentation comments to [email protected] A-6 Cisco MDS 9100 Series Hardware Installation Guide OL-21514-01 Appendix A Cabinet and Rack Installation Cisco MDS 9000 Family Telco and EIA Shelf Bracket To install the shelf brackets in a telco rack, follow these steps: Step 1 Position a shelf bracket inside a rack-mounting rail as shown in Figure A-1 and align the screw hol

• Send documentation comments to [email protected] 2-5 Cisco MDS 9100 Series Hardware Installation Guide OL-21514-01 Chapter 2 Installing the Cisco MDS 9100 Series Installing the Switch in a Cabinet or Rack Tip Keep the shipping container in case the chassis requires shipping in the future. Note If you purchased Cisco support through a Cisco reseller, contact the reseller direc

Related Products and Documents (Switch):

Comparable Devices:

Similar Resources:

• Tripp Lite NetDirectorB030-DP16-17DIP (24 pages) 1Quick Start GuideNetDirector® Rack-MountConsole KVM Switch with IP AccessModels: B030-008-17-IP, B030-DP08-17DIP, B030-DP16-17DIPWARRANTY REGISTRATIONRegister your product today and be automatically entered to win an ISOBAR® surge protector in our monthly drawing!tripplite.com/warranty1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/supportC …

• Hama 00039684 (12 pages) All listed brands are trademarks of the corresponding companies. Errors and omissions excepted, and subject to technical changes. Our general terms of delivery and payment are applied.Hama GmbH & Co KGD-86651 Monheim/Germanywww.hama.comr Manual de utilizareConţinut pachet:1 x USB-2.0-Hub1 x Manual de utilizare Ccondiţii sistem:• Sistem de operare …

• Idem KLTM-RFID (2 pages) Tongue Switch with Guard Locking & RFID Coding Quick Connect (QC) M23 12 way Male Plug (Pin view from Switch) Switch Circuit 1 0V Supply 0V.dc 2 R+ 24V.dc Supply 24V.dc 3 S+ 24V.dc Unlock signal (solenoid) apply +24V.dc 4 6 11/12 Safety output circuit 7 8 21/22 Saf …

• Aeon Labs Aeotec G2 (2 pages) DiagramMicro Double Switch G21. Remove the two screws securing the cover plate.While the Micro Double Smart Energy Switch G2 is powered in a 3-wire system, each external switch/button can be toggled to initiate pairing into the Z-Wave network. Or the internal button can be pushed to initiate pairing into the Z-Wave network if the Micro Double Smart Energy Sw …

• Belden Hirschmann SPIDER II 8TX (29 pages) SPIDER IIRelease 04 09/09Technical [email protected] ManualInstallationIndustrial ETHERNET Rail SwitchSPIDER II, SPIDER II Giga, SPIDER II PoESPIDER II 8TXSPIDER II 8TX EECSPIDER II 8TX/1FX EECSPIDER II 8TX/1FX-SM EECSPIDER II 8TX/1FX-ST EECSPIDER II 8TX/2FX EECSPIDER II 8TX/2FX-SM EECSPIDER II 8TX/2FX-ST EECSPIDER II Giga 5T/2S EECSPIDER …

• H3C S9500 Series (36 pages) Operation Manual – MPLS VLL H3C S9500 Series Routing Switches Table of Contents i Table of Contents Chapter 1 MPLS VLL ..................................................................................................................... 1-1 1.1 MPLS VLL Overview............................................................................................... …

Comments, Questions and Opinions: