Code Soft s4 Operation & User’s Manual

Text of Code Soft s4 User Guide:

• Code Soft s4, Ver:1.1 s4 series user’s manual 19 4. Insert the peeler cable to printer. (Please follow the correct connector side as figure shown to insert the cable) 5. Insert firstly the right side of peeler module to the relative holes of printer (arrow 1), press the lower part of left side of module (arrow 2), then push the left side of module to the relative holes of printer to fix firmly the peeler module on printer (arrow 3).

• Code Soft s4, Ver:1.1 s4 series user’s manual 20 6. Screw up the metal plate on the platen. The metal plate with arrow symbol is upward side. 7. Put the platen screwed with metal plate back to printer 8. Assure the platen is fixed firmly in printer.

• Code Soft s4, Ver:1.1 s4 series user’s manual 6 5. Insert an empty media core into the take up spindle. Rotate the take up hub until the notches align and lock on the left side of take up hub. 6. Pull the ribbon out from the roll and stick it with the adhesive tape on the empty ribbon take up core.

• Code Soft s4, Ver:1.1 s4 series user’s manual 44 Ethernet port 10/100Mbps (option) 1D barcodes Code39 standard or extended, Code39 with check digit, Code93, Code128 UCC, Code128 auto A,B,C modes, Codabar, EAN8, EAN8/13 2&5 digit add-on, EAN13, Interleaved 2 of 5, Interleaved 2 of 5 with check digit, Interleaved 2 of 5 with human readable check digit, UCC/EAN 128, UPC A, UPC A 2&5 digit add-on, UPC E, UPC E 2&5 digit add-on, UPC Interleaved 2 of 5 2D barcodes Data Matrix, MaxiCode, PDF41

• Code Soft s4, Ver:1.1 s4 series user’s manual 42 6. Troubleshooting 6.1 LCD error message LCD Displayed Possible problem Resolution Improper sensor type Ensure the sensor type, reflective or see-through, is selected correctly Label senor cable is disconnected or loose Reconnect or tighten up the sensor cable Sensor windows are dirty Clean the receiver sensors and emitter sensor Improper media sensor position Adjust the media sensor to correct position Label gap out Load the continuous label, but the label

• Code Soft s4, Ver:1.1 s4 series user’s manual 45 7.2 Universal Serial Bus (USB) port pin assignment Connector type: Type A and B USB A (Master) USB B (Slave) Pin Function 1 VBUS 2 D- 3 D+ 4 GND Note: Master VBUS provides +5V max current 500mA. Slave VBUS is N/C. For more information about USB, please visit the website: www.usb.org .

• Ver:1.1 s4 series user’s manual 36 Config. Method-DHCP or Static IP IP address Net Mask Gateway MAC address Configure (Ethernet)-Configure the Ethernet DHCP-Issuing the IP address by DHCP server Static IP- Issuing the IP address by operator DHCP

• Code Soft s4, Ver:1.1 s4 series user’s manual 39 5.2.4 Test Parameter Explanation Print Configuration Print all the printer configurations Print test Print the programmed file to verify if the printer works properly Label calibration Calibrate the label Dump mode Print the Dump mode information Cutter Cutter function test 5.2.5 Memory Parameter Explanation Free size Shows the available memory size on SD card and SDRAM List List the stored forms, images and fonts in SD card and SDRAM. Delete file Delete the stored forms, images and fonts in SD

• Code Soft s4, Ver:1.1 s4 series user’s manual 29 10. Close the printer top cover Please do not touch or insert your fingers into the cutter mouth while cutter is active. It will cause extremely hurt.

• Code Soft s4, Ver:1.1 s4 series user’s manual 3 1.2.3 Interior view Media roll holder Media guide Adjustable media gap sensor Platen roller Cover-up sensor Media holder lock latch Supply spindles Printhead Array sensors Take up spindles Tear-o ff blad e Dispenser (option) Peel-off roller P ee l e r se n so r Peeler bar Dispenser cover Media sensor

• Ver:1.1 s4 series user’s manual 40 5.2.7 Warning message Icon Explanation No form found Form in SD card or SDRAM is not found. Check if the files are exactly stored in the memory device No Image found Image in SD card or SDRAM is not found. Check if the image is exactly stored in the memory device No font found Font in SD card or SDRAM is not found. Chec

More Instructions:

Code Soft s4 Operation & user’s manual 03-02-2024 51

DOWNLOAD

Related Products and Documents (Printer):

Comparable Devices:

Similar Resources:

• Panasonic DP-6010 (130 pages) Digital Imaging SystemsBefore operating this equipment, please read the instructions completely and keep these operating instructionsfor future reference.Getting To KnowYour MachineBefore StartingMaking CopiesOptionsModel No. DP-3510/4510/6010Operating Instructions(For Copier & Network Scanner)EnglishNetwork ScannerJ?IOthersP001_4510(pb).p65 7/31/02, 10 …

• Canon i320 (56 pages) Color Bubble Jet PrinterColor Bubble Jet PrinterColor Bubble Jet PrinterColor Bubble Jet PrinterQuick Start GuideQuick Start GuideQuick Start GuideQuick Start Guide …

• Canon 3478B005AA (8 pages) ADVANCED AIO PERFORMER• UFRII Lt Print Technology for no wait-time• 30ppm print & copy speed• 50-sheet Duplex ADF• 128MB RAM shared memory• Quick First Print (QFP) within 8 seconds• Network-readyHIGH RELIABILITY• Low power save mode (approximately 3W)• Save 50% & more paper with Auto-Duplex print & copy• …

• Kodak Smile (79 pages) User GuideKODAK SMILE INSTANT PRINT DIGITAL CAMERAAppareil photo numérique à impression instantanée Fotocamera digitale a stampa istantaneaDigitale SofortdruckkameraCámara digital con impresión instantánea Guide de l'utilisateurGuida utenteBenutzerhandbuchGuía del usuario …

• Canon BJC-2100 Series (9 pages) BJC-2100 Series Quick Start Guide Step 1: Unpack The Printer 1. Remove all items from the box. • The Install Me First CD-ROM includes: o Microsoft ® Windows ® printer drivers o Macintosh ® printer driver o IS-22 Color Scanner Cartridge driver o Online User's Manual o Software applications o Electronic registration 2. Remove all shippin …

• Sartorius YPD20-OCE (112 pages) Operating Instructions | Betriebsanleitung | Installation et mode d’emploiSartorius YDP20-0CEData Printer | Messwertdrucker | Imprimante98647-004-3598647-004-35 …

Comments, Questions and Opinions: