Manualios.com

ASL INTERCOM VAR8 Operation And Maintenance Manual

ASL INTERCOM VAR8 Manual Online:

4.55, 683 votes
ASL INTERCOM VAR8 User Manual
ASL INTERCOM VAR8 User Guide
ASL INTERCOM VAR8 Online Manual

Text of ASL INTERCOM VAR8 User Guide:

  • ASL INTERCOM VAR8, VAR8 and Variants Operation, Commissioning, Fault Finding, and Maintenance Guide - Is Page 138 of 166 sue: 02 complete, approved VAR8 Menu Description Ref. Item Description/Possible Settings 103 ANS Enables the user to configure the settings for ambient noise sensor processing on the selected output: ‘On’/‘Off’: Whether ANS is enabled on the output. ‘Min’: Threshold in dBA below which ANS correction does not occur (65 to 89dB). ‘Max’: Maximum noise level in dBA applied to compensate for ambient noise (81 to 95dB). It is used to limit the range over which the gain maybe increased from its set value. ‘Attack’:

  • VAR8 and Variants Operation, Commissioning, Fault Finding, and Maintenance Guide sue: 02 complete, approved - Is Page 59 of 166 Page 59 of 166 9.6.2 Single Button Microphone Button Configuration 9.6.2 Single Button Microphone Button Configuration The PTT button of a Single Button Microphone may be configured to broadcast a single output, or a group of outputs. Pre

  • VAR8 and Variants Operation, Commissioning, Fault Finding, and Maintenance Guide sue: 02 complete, approved - Is Page 53 of 166 4. Program the DVA that will be played to the selected zones when the button is pressed. Menu: ConfigurationÆSystemÆRouterÆInputsÆMic/LineÆI/P #<nn>Æ<mic type>ÆButtons ÆPlay DVAÆSelect DVA The inputs

  • ASL INTERCOM VAR8, VAR8 and Variants Operation, Commissioning, Fault Finding, and Maintenance Guide sue: 02 complete, approved - Is Page 111 of 166 23 Night Time Volume Control Configuration The Router provides the facility of automatically reducing the volume of announcements at certain times of day, usually during the night. The Night Time Volume Control function limits the level for each output to a configurable maximum level during its active time. To Configure the Night Time Volume Control: 1. Enable (or disable) the Night Time Volume Control function. Menu: ConfigurationÆSystemÆRouterÆNoise

  • VAR8 and Variants Operation, Commissioning, Fault Finding, and Maintenance Guide sue: 02 complete, approved - Is Page 121 of 166 Page 121 of 166 • Menu: ConfigurationÆSystemÆViewÆVerbose • Menu: ConfigurationÆSystemÆViewÆVerbose Enables the user to scroll through detected frames, and through the slots within the frame. Each entry displays the frame number and softwar

  • ASL INTERCOM VAR8, VAR8 and Variants Operation, Commissioning, Fault Finding, and Maintenance Guide sue: 02 complete, approved - Is Page 56 of 166 Page 56 of 166 Reference to Configuration Tool Reference to Configuration Tool 1 Selected Zones 3 2

  • ASL INTERCOM VAR8, VAR8 and Variants Operation, Commissioning, Fault Finding, and Maintenance Guide sue: 02 complete, approved - Is Page 109 of 166 22 Busy Indication Configuration The digital outputs of a Remote I/O Unit may be assigned as ‘Busy Outputs’. Each such output may be assigned to correspond to the busy state of any Router output or group of outputs. In the case of a group of outputs, it operates as an OR function of the busy state of the outputs, i.e. if any of them are busy, the digital output is driven. It is possible to co

  • VAR8 and Variants Operation, Commissioning, Fault Finding, and Maintenance Guide sue: 02 complete, approved - Is Page 48 of 166 9.6.1.3 DVA Routing/Other Input Routing Button L • DVA Routing is only available for Paging or Zoned Fire Microphones that are connected to Router’s Mic/Line inputs 1 or 2. • Although described as ‘DVA Routing’ this function

  • ASL INTERCOM VAR8, VAR8 and Variants Operation, Commissioning, Fault Finding, and Maintenance Guide - Is Page 44 of 166 sue: 02 complete, approved 9.6 Microphone Button Configuration 9.6.1 Paging or Zoneable Fire Microphone Button Configuration Microphone buttons may be programmed for either: • Not-Conf – Section “9.6.1.1 Unused Button” The button has no associated function. It is important that any button that is not in use should be configured as unused, to prevent inadvertent operation. • Microphone Routing or Zone Select – Section “9.6.1.2 Microphone Routing or Zone Select

  • ASL INTERCOM VAR8, VAR8 and Variants Operation, Commissioning, Fault Finding, and Maintenance Guide sue: 02 complete, approved - Is Page 30 of 166 Figure 4 Intellevac 8x8 ACU Network Topology Network O/P 44 Network O/P 42 Network O/P 41 Network O/P 101 Network O/P 48 4 3 2 1 8 7 6 5 8 7 6 5 Network O/P 106 Network O/P 95 Network O/P 45 4 3 2 1 Network O/P 07 Network O/P 05 12 11 10 9 Network O/P 63 Network O/P 61 Network O/P 68 Network O/P 24 Network O/P 23 Network O/P 22 Network O/P 21 Network O/P 56 Network O/P 55 Network O/P 54 Network O/P 53 Network O/P 36 Network O/P 35 Network O/P 34 Network O/P 33 Network O/P 12 Network O/P 11 Network O/P 09 Networ

  • ASL INTERCOM VAR8, VAR8 and Variants Operation, Commissioning, Fault Finding, and Maintenance Guide - Is Page 16 of 166 sue: 02 complete, approved 13. Configure local inputs, as described in Section “9 Local Input Configuration” (page 36). 14. Configure DVA, as described in Section “10 DVA Input Configuration” (page 61). 15. Configure background music (if used), as described in Section “11 Music Input Configuration” (page 67). 16. Configure mute input priority (if used), as described in Section “12 Mute Input Configuration” (page 74). 17. Configure the local output/zones, as described in Section “13 Output/Zone Configuration” (page 76). 18. Configure any local permanent

  • ASL INTERCOM VAR8, VAR8 and Variants Operation, Commissioning, Fault Finding, and Maintenance Guide sue: 02 complete, approved - Is Page 65 of 166 Page 65 of 166 10.4 Priority Set-up 10.4 Priority Set-up L L • 19 priority levels are assignable to any of the DVA inputs. • 19 priority levels are assignable to any of the DVA inputs. • Assignment of equal priorities means that those inputs operate on a ‘first-come-first-served’ basis. • Assignment of equal priorities means that those inputs operate on a ‘first-come-first-served’ basis. • The lower the priority value, the higher the priority. • The lower the priority value, the higher the prio

  • ASL INTERCOM VAR8, VAR8 and Variants Operation, Commissioning, Fault Finding, and Maintenance Guide - Is Page 163 of 166 background music.........................................41, 70 remote i/o unit digital.....................................103 defaults..........................................................158 O output sue: 02 complete, approved 33 Index A access code........................................................18 amplifier change-back..................................................121 changeover ...................................................121 commissioning....................................

  • ASL INTERCOM VAR8, VAR8 and Variants Operation, Commissioning, Fault Finding, and Maintenance Guide - Is Page 151 of 166 sue: 02 complete, approved Fault Description Fault Code(s) Reported and Logged Suggested Action Remote I/O Unit Comms Fault REMXX REMOTE I/O COMMS XX=Remote I/O Unit Address Check the Comms and power wiring to Remote I/O Unit. Check RS485 termination. Check that address of Remote I/O Unit is correct. If all above ok, suspect the unit itself. Check the unit’s internal CPU and COMMS LEDs. Remote I/O Unit analogue channel fault (open or short) REMXX ANALOGUE I/P nn XX=Remote I/O Unit Address nn=Analogue Input Channel Check wiring of Volume

  • ASL INTERCOM VAR8, VAR8 and Variants Operation, Commissioning, Fault Finding, and Maintenance Guide sue: 02 complete, approved - Is Page 70 of 166 8. Define the time over which this audio channel is faded up/down when audio sources change. A slow fade up time is desirable for music inputs. Menu: ConfigurationÆSystemÆRouterÆInputsÆMic/LineÆI/P #<nn>ÆAudioÆFade L • A slow fade up time is desirable for music inputs. • The time is given in tenths of a second, so divide by ten for the time in seconds. • It is important for Fire Microphones to be able to override other sources quickly;

  • VAR8 and Variants Operation, Commissioning, Fault Finding, and Maintenance Guide sue: 02 complete, approved - Is Page 14 of 166 3.4 Menu Map of Functions [Configuration] [Tests] [Faults] [Access] [System] [Date/Time][Frames] [LogOff] [Change-Code] [Clear config] [Frame#nn - ...] [Commis.] [Desc.] [Temp] [Slot#nn] [Desc.] [AC Level] [Spurs=00] [Earth] [Frequency] [Thresholds] [Interv

  • ASL INTERCOM VAR8, VAR8 and Variants Operation, Commissioning, Fault Finding, and Maintenance Guide sue: 02 complete, approved MUSIC FADE UP=T1 FADE DOWN= T2 T4 T1 MICROPHONE FADE UP=T3 FADE DOWN= T4 T3 T4 MICROPHONE PTT ON ON OFF OFF MUSIC AUDIO MUSIC AUDIO MIC AUDIO CHIME AUDIO MICROPHONE SPEAK-NOW LED - Is Page 71 of 166 Figure 8 Sequence of Events for Paging Microphone Chime Overriding a Background Music 9. If using a balanced input for background music, ensure that: a. The surveillance detection is disabled. b. The chime is disabled.

  • ASL INTERCOM VAR8, VAR8 and Variants Operation, Commissioning, Fault Finding, and Maintenance Guide - Is Page 29 of 166 sue: 02 complete, approved 8.1.2 8x8 ACU Network Topology The Intellevac Network’s 8x8 Audio Control Unit supports the following Slave Units: • Wall mount Intellevac Distributed Amplifier Units, both legacy 4x4 DAUs and 8x8 DAUs. • Rack mount VAR12 and VAR20 Routers, using the VAR Network Interface Adapter (VAR-NIA). • Rack mount VAR8 Routers fitted with ANIC Network Interface Card. The Audio Control Unit normally ‘talks’ out of its UPSTREAM port, which is connected to the DOWNSTREAM port of the first Slave Unit in the chain. The UP

  • ASL INTERCOM VAR8, VAR8 and Variants Operation, Commissioning, Fault Finding, and Maintenance Guide sue: 02 complete, approved - Is Page 75 of 166 Page 75 of 166 12.2 Priority Set-up 12.2 Priority Set-up To Set-up the Mute Input Priority: To Set-up the Mute Input Priority: 3. Select the Mute input, and then allocate priority independently to each of the Router outputs as required. 3. Select the Mute input, and then allocate priority independently to each of the Router outputs as required. Menu: ConfigurationÆSystemÆRouterÆInputsÆMic/LineÆI/P #10 – SLAVE MUTEÆCtrlÆPri Menu: ConfigurationÆSystemÆRouterÆInputsÆMic/

  • ASL INTERCOM VAR8, VAR8 and Variants Operation, Commissioning, Fault Finding, and Maintenance Guide sue: 02 complete, approved - Is Page 113 of 166 24 System Configuration 24.1 Changing the System Access Code 1. The access code can be changed once the user is logged onto the system through the following menu. Menu: ConfigurationÆAccessÆChange-Code 24.2 System Date and Time The Router features a real time clock, which is used for time and date stamping of log entries such as fault reports. This is fitted with an internal Lithium battery so that the clock continues running without power applied. 2. It is possible to change the system date and time as

  • ASL INTERCOM VAR8, VAR8 and Variants Operation, Commissioning, Fault Finding, and Maintenance Guide sue: 02 complete, approved - Is Page 42 of 166 Page 42 of 166 11. Define the type and level of chime, if any, to be sounded prior to microphone announcement. 11. Define the type and level of chime, if any, to be sounded prior to microphone announcement. If configured, the chime will be triggered when the input source is routed. However the actual audio input will only be routed when the chime is complete. Three types of chime are available: one; two; or three chimes, or none. If configured, the chime will be trigg

  • ASL INTERCOM VAR8, VAR8 and Variants Operation, Commissioning, Fault Finding, and Maintenance Guide - Is Page 3 of 166 sue: 02 complete, approved Contents 1 Introduction .............................................................................................................................................. 7 1.1 Important Notes .......................................................................................................................... 7 1.2 Equipment Requirement......................................................................................................

  • ASL INTERCOM VAR8, VAR8 and Variants Operation, Commissioning, Fault Finding, and Maintenance Guide - Is Page 137 of 166 sue: 02 complete, approved VAR8 Menu Description Ref. Item Description/Possible Settings L Mute input is a special input, which mutes even fire microphones if needed. For this purpose its priority is set to ‘0’ by default. However, the mute input is configurable, so it is possible to mute just DVAs , and/or any other inputs. Having chosen Mute input ‘Pri’ and ‘Name’ sub-menus are displayed. 96

  • ASL INTERCOM VAR8, VAR8 and Variants Operation, Commissioning, Fault Finding, and Maintenance Guide sue: 02 complete, approved - Is Page 114 of 166 24.4 Emergency Sounder Operation 4. It is possible to suppress or enable the fault sounder during announcements from the fire microphone through the following menu. Menu: ConfigurationÆSystemÆRouterÆMiscÆSounder ‘Error beep with fire mic=Enabled’ means that the fault sounder is enabled during fire microphone announcements. ‘Error beep with fire mic=Suppressed’ means that the fault sounder is disabled during fire microphone announcement

  • ASL INTERCOM VAR8, VAR8 and Variants Operation, Commissioning, Fault Finding, and Maintenance Guide sue: 02 complete, approved - Is Page 90 of 166 Page 90 of 166 5. Select if the DVA route should cause busy indication on the LEDs associated with microphone zone select buttons. 5. Select if the DVA route should cause busy indication on the LEDs associated with microphone zone select buttons. Menu: ConfigurationÆSystemÆRouterÆCtrlÆRemoteÆUnit address <n>ÆRoute-trigger <nn> Menu: ConfigurationÆSystemÆRouterÆCtrlÆRemoteÆUnit address <n>ÆRoute-trigger <nn> ÆControlÆBusy=On or Bus

  • ASL INTERCOM VAR8, VAR8 and Variants Operation, Commissioning, Fault Finding, and Maintenance Guide - Is Page 35 of 166 sue: 02 complete, approved 8.3 Audio Control Unit Configuration The VAR8 needs to be configured as Slave Unit at the Audio Control Unit (wall mount Intellevac ACU or rack mount VAR8-ACU). This configuration is described in the Audio Control Unit’s Commissioning and Operation Guide. This guide also describes how to establish and test the network connection. Please contact ASL quoting the type and the software version of your Audio Control Unit. The appropriate guide can then be

Related Products and Documents (Network Router):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Powercraft 69350 Instruction manual powercraft/69350-TCY.pdf 08 Mar 2023 51
2 USA Trains UNION PACIFIC “BIG BOY” Owner's manual usa-trains/union-pacific-big-boy-79D.pdf 02 Jul 2023 4
3 Rotax 447 UL SCDI Installation manual rotax/447-ul-scdi-EOD.pdf 10 Feb 2023 68
4 Blackberry 7130e - CDMA2000 1X Setting-up manual blackberry/7130e-cdma2000-1x-899.pdf 13 Jan 2024 11
5 American Standard Town Square Two-Piece Toilets 2787 Installation instructions american-standard/town-square-two-piece-toilets-2787-OF8.pdf 29 Jul 2022 4
6 RCA L42FHD37R - 41.9" LCD TV Guía del usuario rca/l42fhd37r-41-9-lcd-tv-99O.pdf 23 Jun 2022 40 5.07 Mb

Similar Resources:

  • Advantech

    B+B SmartWorx SE416

    (2 pages)
    Product OverviewHardware InstallationLED StatusTerminal Blocks132DIN Rail MountingTerminal DescriptionV2- Power Input 2 (DC Ground)V2+ Power Input 2 (12 to 48VDC)P-Fail Power Fault RelayP-Fail Power Fault Relay V1- Power Input 1 (DC Ground)V1+ Power Input 1 (12 to 48VDC)Wire Gauge: 12-24 AWG (3.31 - 0.205 mm2).Torque: 7lb-in.NOTE: P-Fail Relay is …
  • Terra

    dSCR multiswitch SRM580

    (2 pages)
    Draugystes str. 22, LT-51256 Kaunas, Lithuania, tel.: +370 37 - 31 34 44, fax: +370 37 - 31 35 55 E-mail: [email protected], http://www.terraelectronics.com This product complies with the relevant clauses of the European Directive 2002/96/EC. The unit must be recycled or discarded according to applicable local and national regulations. Equi …
  • Ubiquiti

    EdgeRouter ER-12P

    (26 pages)
    EdgeRouter ER-12P Wall Mount Screws (Qty. 2) Wall Mount Anchors (Qty. 2)Ground Screw Power Adapter (24V, 2.5A) Power CordPackage ContentsCreate PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD …
  • Gembird

    WNP-RT-001

    (14 pages)
    USER MANUALHANDBUCHHANDLEIDINGMANUEL DESCRIPTIFРУКОВОДСТВО ПОЛЬЗОВАТЕЛЯКЕРІВНИЦТВО КОРИСТУВАЧАWIRELESS BROADBAND ROUTER, 300 MBPSWIRELESS BREITBANDROUTER, 300 MBPSDRAADLOZE ROUTER, 300 MBPSROUTEUR HAUT DÉBIT SANS FIL, 300 MBPSБЕСПРОВОДНОЙ СЕТЕВОЙ МАРШРУТИЗАТОР, 300 МБИТ/СЕК� …
  • Cisco

    6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion

    (570 pages)
    Corporate HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706 USAhttp://www.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 526-4100Catalyst 6500 Series Switch Cisco IOS Software Configuration Guide—Release 12.1 ECisco IOS Release 12.1 ECustomer Order Number: DOC-7814099=Text Part Number: 78-14099-04 …
  • Sprint

    AIRAVE 2.5+

    (33 pages)
    911702 Rev. 51.12 AIRAVE 2.5 User Guide ©2012 Sprint. Sprint and the logo are trademarks of Sprint. Other marks are trademarks of their respective owners. …

Comments, Questions and Opinions: