AGA TC3 Installation Manual
|
4. Run a straight edge along the front of the AGA Total Control plinth, to ensure the front face of both plinths sit squarely against the straight edge. (See Fig. 10) When satisfied both plinths sit squarely, jacking screws can be tightened until they just make contact with the AGA Total Control plinth and locking screws can now be tightened. Fig. 10 DESN 516551 USE STRAIGHT EDGE A
AGA TC3, CONNECTION TO THE POWER SUPPLY - AGA TC3 Electric Shock Hazard Rating Plate is located behind removable plinth, see Fig. 4. Electrical Grounding is required on this appliance. DO NOT connect to the electrical supply until the appliance is permanently grounded. Disconnect the power to the junction box before making the electrical connection. This appliance must be connected to a grounded metallic permanent supply or a grounding connector should be connected to the grounding terminal or wire lead on the appliance. Failure to follow these inst
AGA TC3, 24 For further advice or information contact your local AGA Specialist With AGA’s policy of continuous product improvement, the Company reserves the right to change specifications and make modifications to the appliance described and illustrated at any time US Office: AGA MARVEL 1260 E Van Deinse St. Greenville, MI 48838 www.agamarvel.com
AGA TC3, GENERAL NOTES 3 NOTE: THESE INSTALLATION INSTRUCTIONS SHOULD BE LEFT WITH THE APPLIANCE AND THE USER TO RETAIN FOR FUTURE REFERENCE. Before installation of an AGA can be made, the site is inspected for suitability by an authorized AGA distributor and corrected where necessary to conform with local or regional electrical codes. DELIVERY REQUIREMENTS The AGA TC3 arrives on 1 pallet. The AGA TC5 (Hotcupboard Option) arrives on 2 pallets. There must be access to the kitchen to manipulate a foot print of 39 9 /16” (1005mm) x 29 1 /8” (740mm). A wooden template (skate with castor wheels) of dimensions 39 9 /16” (1005mm) x 29 1 /8” 740
Installation Guide 11/12 EINS 516294 PLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING SITE SURVEY OR INSTALLING THIS APPLIANCE. IMPORTANT : SAVE INSTRUCTIONS FOR THE LOCAL INSPECTORS USE CUSTOMER: KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE REMEMBER: when replacing a part on this appliance, use only replacement parts that you can be assured conform to the safety a
AGA TC3, 17 HANDRAIL CONNECTION - AGA TC3 Fig. 16 DESN 516560 Handrail brackets. endcaps and handrails require assembly. Locate endcaps onto handrail, place brackets over endcaps and then slide complete assembly onto locating studs. Once assembly is correctly located, lock into position with grub screws (located on underside of handrail).
AGA TC3, Fig. 12 DESN 516552 6. Slide hotcupboard onto plinth until rear tongue bracket engages fully into rear of base slot, (See Fig. 12). Ensure the appliance is aligned squarely with the plinth then proceed to engage the front tongue bracket into the slot on the underside of the base plate. Once satisfied that the front tongue bracket is engaged fully lock it into place by tightening the two M6 screws fully. 7. The hotcupboard top plate is set 13 /64 (5mm) higher than the AGA Total Control top plate. This is to prevent damage to the enamel during installation. Lower the
AGA TC3, APPLIANCE DIMENSIONS - AGA TC5 5 Fig. 2 DESN 516561 Cooker Dimensions When surveying for a cooker installation the actual clearance required for the ‘body’ of the appliance should be increased by 10mm beyond the figures quote above. This allows safe margin to take into account the natural dimensional variations found in major castings. In particular the width across the appliance recess could be critical. APPLIANCE WEIGHT Model: AGA Total Control (TC3) - 816 lbs (370 Kg) Hotcupboard - 110kg A B C D E F G H J K L mm 1478 945 910 680 1385 760 1145 698 116 10 634 ins 58 13 /16 37 3 /16 35 13 / 16 26 3 /4 54 1 /2 29 15 / 16 45 1 /16 27 1 /2 4
AGA TC3, 4 APPLIANCE DIMENSIONS - AGA TC3 Fig. 1 DESN 516297 Cooker Dimensions When surveying for a cooker installation the actual clearance required for the ‘body’ of the appliance should be increased by 3/8” (10mm) beyond the figures quoted above. This allows safe margin to take into account the natural dimensional variations found in major castings. In particular the width across the appliance recess could be critical. RH SIDE VIEW FRONT VIEW LH SIDE VIEW PLAN VIEW MINIMUM WALL POSITION MINIMUM WALL POSITION APPLIANCE WEIGHT Model: AGA Total Control (TC3) - 816 lbs (370 Kg) PACKAGING
AGA TC3, 8. Using the stay rod nut adjusting tool, carefully lower the top plate adjusting nuts until the top plates sits at the required height, making sure that the top sits level and matches the height of the AGA TC3. (See Fig. 14). Fig. 14 DESN 516555 9. Slide the complete handrail over the left hand, right hand and centre fixing studs. Once the assembly has been fitted to the AGA appliance, fit the handrail endcaps (ensuring the handrail is evenly spaced at each end). The endcaps should be carefully p
AGA TC3, 19 Fig. 18 WIRING DIAGRAM - AGA TC5 (HOTCUPBOARD OPTION) COLOUR KEYS/COLLEURS BR - BROWN/MARRON BL - BLUE/BLEU GR - GREEN/VERT OR - ORANGE/ORANGE BK - BLACK/NOIR CAUTION: LABEL ALL WIRES PRIOR TO DISCONNECTION, WHEN SERVICING CONTROLS WIRING ERRORS CAN CAUSE IMPROPER AND DANGEROUS OPERATION. VERIFY PROPER OPERATION AFTER SERVICING ATTENTION: ETIQUETEZ TOUS LES CABLES AVANT DE LES DEBRANCHER LORS DE LES BRANCHER LORS DE L’ENTRETIEN DES COMMANDES. DES ERREURS DE CABLAGE PEUVENT ENTRAINER UN FONCTIONNEMENT INCORRECT ET DANGEREUX. VERIFIEZ QUE L’ APPAREIL FONCTIONNE CORRECTEMENT APRES L’ENTRETIEN.
2. Position the plinth alongside the AGA Total Control leaving no gap between the two plinths (See Fig. 8). Check with a spirit level that the plinth level is correct, and also check height differential between the hotcupboard plinth and Total Control plinth is correct 7 /16” (11mm). If necessary, use shims in each corner to level the plinth. Fig. 8 DESN 516564 HOTCUPBOARD PLINTH BASE 7
AGA TC3, MAINS SUPPLY LOCATION - AGA TC5 Fig. 5 DESN 516562 MAINS CABLE FED FROM CONTROL TRAY LEFT OR RIGHT EXIT THROUGH DUCTING DEPENDENT UPON POSITION OF SUPPLY SOCKET 11 Fig. 5A DESN 516590 THE MAINS SUPPLY CONNECT POINT MUST BE WITHIN THE ZONES SHOWN HOTCUPBOARD POWER SUPPLY RATING LABEL LOCATED BEHIND PLINTH, PULL TO REMOVE,
AGA TC3, POWER SUPPLY - HOTCUPBOARD (AGA TC5) The hotcupboard attachment requires an independent single phase supply. It has a maximum load of 6 amps, protected by an appropriate branch circuit supply. 110/120V 60 Hz FLEXIBLE CORD AND PLUG PARALLEL TYPE. The appliance when installed, must be electrically grounded in accordance with local or regional codes. An electrical socket must be provided within 5 feet of the LH side of the appliance and easily accessible to the user to disconnect. Do not position socket above the appliance. Take special care when cutting holes in wall or floor. Electrical wires may be behind t
AGA EINS513307 Cooktop Owner's manual
EINS513307 |
AGA U104601-01 Cooktop User's manual & installation instructions
U104601-01 |
AGA Legacy 44 Cooktop Service instructions manual
Legacy 44 |
AGA Companion Cooktop Owner's manual
Companion |
AGA LEGACY 36 Cooktop Service instructions manual
LEGACY 36 |
AGA ACMPLP-SI Cooktop Owner's manual
ACMPLP-SI |
AGA Ludlow Wood Burning Cooktop Installation and operating instructions manual
Ludlow Wood Burning |
AGA TC3 Cooktop Operation & user’s manual
TC3 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Swisher | T1360 | Owner's manual | swisher/t1360-2KO.pdf | 23 Apr 2023 | 24 | |
2 | Vision Fitness | R2000 | Assembly manual | vision-fitness/r2000-LZA.pdf | 17 Sep 2022 | 9 | 1.22 Mb |
3 | Kramer | 3232DS | Specifications | kramer/3232ds-DRQ.pdf | 20 Oct 2022 | 2 | |
4 | ASROCK | AD525PV | Brochure | asrock/ad525pv-O6I.pdf | 13 Sep 2023 | 5 | 1.34 Mb |
5 | Pioneer | Elite BDP-43FD | Specifications | pioneer/elite-bdp-43fd-Q7P.pdf | 03 Jul 2023 | 2 | |
6 | Samsung | Washing machine | Owner's instructions manual | samsung/washing-machine-T26.pdf | 03 Oct 2022 | 8 | 0.59 Mb |
Trieste
Dear User,we are sincerely grateful to you for purchasing one of our products. We are sure that the appliance modern, functional and easy to use, built with the finest materialsand components will satisfy all your needs. We would ask that you read the instructions within this booklet very carefully so as to enable youto obtain quality results from the outset …
TRV602IX(12 pages) |
Wolf
ELECTRIC COOKTOPSUSE & CARE INFORMATIONGUÍA DE USO Y MANTENIMIENTOGUIDE D’UTILISATION ET D’ENTRETIENINFORMAZIONI SU USO E MANUTENZIONEBEDIENUNGS- UND PFLEGEANLEITUNG
…
ICBCT15E(94 pages) |
Whirlpool
SELF-CLEANINGELECTRIC RANGESUse & Care GuideFor questions about features, operation/performance,parts, accessories or service, call: 1-800-253-1301.In Canada, call for assistance 1-800-461-5681, for installationand service, call: 1-800-807-6777or visit our website at...www.whirlpool.com or www.whirlpoolappliances.caTable of Contents...................... …
Ranges(20 pages) |
Dacor
NOTES: Contains helpful hints and tips.WARNINGS: Must be followed carefully to avoid personal injury or damage.IMPORTANT INFORMATION• Operating Instructions• Care and Cleaning Instructions• Safety TipsSAFETY IS EVERYONE’S RESPONSIBILITY. ALL DACOR APPLIANCES ARE DESIGNED AND CONSTRUCTED TO GIVE YOU MANY YEARS OF SAFE OPERATION. THE OPERATION WIL …
EpicureTM(20 pages) |
Jøtul
Jøtul FS 84 AdvanceThe manuals which are enclosed with the product must be kept throughout the product’s entire service life. Les manuels fournis avec le produit doivent être conservés pendant toute la durée de vie du produit.UK - Installation and operating instructions 3FR - Manuel d’installation et d’utilisation 36Jøtul FS 84 AdvanceManual v …
FS 84 Advance(68 pages) |
Smeg
22ContentsINSTRUCTIONS FOR THE USER: these contain user advice,description of the commands and the correct procedures forcleaning and maintenance of the appliance.INSTRUCTIONS FOR THE INSTALLER: these instructions are intended for the qualified technician who must perform the installa-tion, put it into operation and test the appliance.1. INSTRUCTIONS FOR US …
G30(19 pages) |
Sirona Medical Equipment CEREC AC BLUECAMSirona CEREC AC BLUECAM Guide (Operating instructions manual), @F2G8ZO CEREC AC BLUECAM, 78 |
Motion Composites Wheelchair Helio A7Operation & user’s manual for Motion Composites Helio A7 Wheelchair Helio A7, 32 |
Pioneer Speakers S-DJ08User Guide: Pioneer S-DJ08 (6J6683, Upd.29.12.2023) S-DJ08, 72 |
Panasonic Computer Hardware TY-UPK110Panasonic TY-UPK110 User Guide (Installation instructions manual), @7O9Z9S TY-UPK110, 12 |
Fieldpiece Multimeter SPDM1Fieldpiece SPDM1 Guide (Operator's manual), @6B57S2 SPDM1, 2 |
Sony Digital Camera Cyber-shot 4-170-840-12(1)PDF Guide (@997I96), Sony Cyber-shot 4-170-840-12(1) Digital Camera (22/01/2024) Cyber-shot 4-170-840-12(1), 36 |
CalComp Tablet EstiMatCalComp EstiMat Tablet Operation & user’s manual EstiMat, 74 |
LAZBOY Patio Furniture D71 M80936#64ZII7: D71 M80936 Patio Furniture Owner's manual D71 M80936, 4 |
Coosis Media Converter HD GAMING PRO 2 HG-PRO2Coosis HD GAMING PRO 2 HG-PRO2 Manual (Doc Type: Media Converter Operation & user’s manual) HD GAMING PRO 2 HG-PRO2, 22 |
Micro Motion Transmitter RFT9739#GPB8P9 RFT9739: Micro Motion Transmitter Owner Documentation RFT9739, 11 |
Furuno Marine Radio P4800Marine Radio Owner's manual (Furuno P4800) P4800, 30 |
Fisher-Price Motorized Toy Car A.T. REX M7873#7O72WM A.T. REX M7873: Fisher-Price Motorized Toy Car Owner Documentation A.T. REX M7873, 20 |