Manualios.com

SAGEMCOM MF 9626 Installation Manual

SAGEMCOM MF 9626 Manual Online:

4.45, 761 votes
SAGEMCOM MF 9626 User Manual
SAGEMCOM MF 9626 User Guide
SAGEMCOM MF 9626 Online Manual

Text of SAGEMCOM MF 9626 User Guide:

  • SAGEMCOM MF 9626, MF 9841 MF 9626/9631/9841 1 – 2 (2) Dust If dust enters the machine, it may cause dirty copy and a paper jam, resulting in a shortened lifetime. (3) Direct rays of sunlight If the machine is installed under the rays of the sun, the exterior of the machine may be discolored and abnormal copies may be pro- duced. (4) Gases and chemicals Do not install the machine at a place where there are gases and chemicals. Especially be careful to avoid installation near a diazo- type copier, which produces ammonium gas. Copy quality may be adversely affected and a trouble may be caused. (5) Vibration Avoid installation near a machine which produces vibrations. If vibrati

  • SAGEMCOM MF 9626, MF 9841 SG-GCX1 4 – 4 5) In the case of a shift to the right, press the front upper section and fit the height adjustment check rib so that it is in the same line with the axis line of the mounting plate upper. Insert the large capacity tray unit into the main unit. 6) In the case of a shift to the left, lift the grip so that the height adjustment check rib is in the same line with the axis line of the mounting plate upper, and insert the large capacity tray unit. 7) Tighten the loosened screw. D. Connector connection 1) Remove the screw, and remove the connector cover. 2) Connect the connector, and tighten the screw. E. Paper size switch (1

  • SAGEMCOM MF 9626, MF 9841 SG-ETX1/ETX2 3 – 2 3) Remove the paper exit cover. [MF 9626/9631] Remove the screw, and remove the paper exit cover. [MF 9841] Remove the screw. Disengage the engagement in the front side then in the rear side, and remove the paper exit cover. 4) Connect the connector, and install the exit roller unit (package part No. 1). Use the screw which was removed in step 3) and fix the unit. [MF 9626/9631] [MF 9841] 5) Install the connector cover, and fix it with the screw. 6) Install the exit tray unit (A) and the full detection actuator (B) (package part No. 2). * Be careful of the installing direction of the full detection a

  • SAGEMCOM MF 9626, INSTALLATION MANUAL Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. This document has been published to be used for after sales service only. The contents are subject to change without notice. MF 9626 MF 9631 MF 9841 CONFIGURATION [1] MF 9626/9631/9841 (Main Unit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 [2] SG-CPX4/CPX6 (Stand/2x500 sheet paper drawer) . . . . . . . . . . . . . . . .

  • MF 9841 SG-FNX3 5 – 3 3) Disengage two pawls, and remove the paper exit tray cover. 4) Remove four screws, and remove the paper exit tray. * When removing the paper exit tray, there is no need to remove the screws in the section (A). 5) Remove the paper exit full detection actuator. 6) Engage the projection on the main unit frame with the hole in the finisher fixing plate (package

  • SAGEMCOM MF 9626, MF 9841 SG-FEX2 10 – 2 2) Remove the screw from the right rear cabinet and remove the right rear cabinet. 3) Remove the two screws from the control PWB unit. 4) Pull out the control PWB unit. D. Attach the FAX memory. 1) Install the FAX memory to the socket on the controller PWB as shown in the figure below so that the memory notch is on the right side. E. Attach the interface cable. 1) Connect the interface cable to the control PWB unit. [Note] Check that the connector is not obliquely inserted. 2) Push the interface cable into the recessed portion of the sheet metal on the control PWB unit. 3) Fix a snap band with the bundled M3 screw. F. Attach the control PWB an

  • SAGEMCOM MF 9626, MF 9841 SG-FNX3 5 – 5 3) Connect the finisher connector with the main unit connector, and tighten with a screw. E. Staple position label attachment 1) Attach the label to the position indicated in the figure. [For scanner] (package part No. 11) [For RSPF/DSPF] (package part No. 12) F. Turn on the power of the main unit 1) Insert the power plug of the main unit into the power outlet. 2) Open the front cabinet. Turn ON the power switch in the front cabinet of the main unit. 3) Turn ON the power switch on the operation panel. Second label Corner R end fitting Label attachment reference Corner of the "upper cabinet

  • SAGEMCOM MF 9626, MF 9841 SG-KBX1 12 – 1 MF 9841 Service Manual [12] SG-KBX1 1. Unpacking A. Check the parts in the package 2. Installation <Note before installation> * Before starting installation, check to insure that the data lamp on the operation panel does not light up or blink. A. Turn off the power of the main unit 1) Turn OFF the power switch on the operation panel. 2) Open the front cabinet. Turn OFF the power switch in the front cabinet of the main unit. 3) Disconnect the power plug of the main unit from the p

  • SAGEMCOM MF 9626, MF 9841 MF 9626/9631/9841 1 – 7 6) Select K, C, M, Y and then press the [EXECUTE] button. The system then performs the simulation, samples the toner den- sity control sensor value, and sets (stores in memory) the average sensor detection level as the control level for the ref- erence toner density. (Operating times: approx. 3 minutes) Note: Be sure to select all of the four colors: K, C, M, Y 7) After the machine completes cycling, exit the simulation mode by pressing the [CA] key on the main unit. D. Installation of individual color toner cartridges * The life o

  • SAGEMCOM MF 9626, MF 9841 SG-GCX1 4 – 2 2) Open the front cabinet. Turn OFF the power switch in the front cabinet of the main unit. 3) Disconnect the power plug of the main unit from the power out- let. B. Connection of the main unit and the large capacity tray unit 1) Install the mounting plate upper (package part No. 1) to the right side of the main unit with the fixing screw A (package part No. 3). * When installing, put the rubber section of the mounting plate upper on the lower side. 2) Remove the right door cover from the machine. 3) Diseng

  • SAGEMCOM MF 9626, MF 9841 SG-ECK1 13 – 1 MF 9841 Service Manual [13] SG-ECK1 1. Unpacking A. Parts included 2. Installation A. Turn off the power of the main unit 1) Turn the power switch located on the operation panel to the "OFF" position. 2) Open the front cabinet. Turn OFF the power switch in the front cabinet of the main unit. 3) Disconnect the power plug of the main unit from the power out- let. B. Pull out the control PWB • If cables are connected to the control PWB unit, remove all cables. 1

  • SAGEMCOM MF 9626, MF 9841 SG-ECK1 13 – 2 C. Installation of the scanner function expansion PWB 1) Remove four screws for fixing the scanner function expansion PWB from the control PWB. 2) Install the scanner function expansion PWB to the control PWB by using the four screws for fixing the scanner function expansion PWB. Check that the connectors for connecting each PWB are prop- erly connected. D. Reattach the control PWB and the right rear cabinet • If the fax box unit is installed, carry out steps 1), 2), and 3) additionally. 1) Connect the interface cable to the control PWB

  • SAGEMCOM MF 9626, MF 9841 SG-GCX1 4 – 9 2) Loosen the stopper fixing screw (1 pc) on the right lower side of the tray so that the stopper does not function. 3) Pull out the tray again until it stops. a. When the shift is in the front side To adjust the print line in the direction A from the paper center as shown in the figure: 1) Loosen two fixing screws (red screws) of the front/rear size guide adjustment plate, and move the size guide adjustment plate in the direction A (R side) by the shift amount, and tighten the red fixing screws (2 for each). Move the auxiliary guid

  • SAGEMCOM MF 9626, MF 9841 MF 9626/9631/9841 1 – 4 (2) Scanner (2/3 mirror unit) lock release 1) Remove the optical unit fixing screw, and remove the note label. (3) Removal of the fusing heat roller protector 1) Open the right door. 2) Open the paper guide and pull out the fusing heat roller protec- tor. B. Developing (each color) installation Be careful not to attach fingerprints or oily dirt on the DV roller sur- face. 1) Open the front cabinet. 2) Check that the lock is released as shown in (A). Loosen the blue screw, and open the drum positioning unit. * When the lock is not released, use a screwdriver to t

  • MF 9841 SG-CPX4/CPX6 2 – 2 B. Installation of the adjuster 1) Install the right adjuster (package part No. 1) to the desk unit. 2) Turn each adjuster to fix the desk unit. C. Connection of the main unit and the desk unit 1) Remove the connection plate covers of the both sides of the main unit. 2) Put the main unit on the desk unit. * Use man power of four persons or more to lift the

  • SAGEMCOM MF 9626, MF 9841 SG-PMX1 6 – 4 16) Slide the inner finisher to the original position, and close the front cover. C. Punch position label attachment 1) Attach the label to the position indicated in the figure. [For scanner] (package part No. 1) [For RSPF/DSPF] (package part No. 2) D. Turn on the power of the main unit 1) Insert the power plug of the main unit into the power outlet. 2) Open the front cabinet. Turn ON the power switch in the front cabinet of the main unit. 3) Turn ON the power switch on the operation panel. 2 1 Second label Corner R end fitting Lose the clearance. First label Label attachment reference Corner of the "upp

  • SAGEMCOM MF 9626, MF 9841 SG-BPX2 7 – 2 3) Disconnect the power plug of the main unit from the power out- let. B. Removal of the paper holding arm unit 1) Push up the section A to disengage the pawl, and remove the paper holding arm and the paper holding arm holder together as a unit. * Be careful to remove both of the paper holding arm (which is easily removed alone) and the paper holding arm holder. C. Installation of the interface pass unit 1) Open the front cabinet. Remove the screws, and remove the front cabinet upper.

  • MF 9841 SG-FEX2 10 – 4 • Country code list screen * Press the [DEST CODE] button on the initial screen to move to the country code list screen. To return to the input screen, press the [BACK] button. J. Clear the image memory. 1) Switch the operation panel to the copy mode and use the key operation [P], [∗], [C], and [∗] to enter the simulation mode. 2) U

  • SAGEMCOM MF 9626, MF 9841 SG-GCX1 4 – 5 a. Side plate size switch 1) Remove four fixing screws (blue screws) which are fixing the upper and the lower sections of the side plate F and the side plate R. 2) Adjust the mark position of the tray and the side plates in the lower section of the side plates F/R according to the desired size. Also adjust the upper section according to the desired size, and fix with the four fixing screws (blue screws). b. Auxiliary guide size switch 1) When switching the size of the side plate R, check to confirm the mark position ( ) of the side plate R and the size

  • SAGEMCOM MF 9626, MF 9841 SG-FNX4 8 – 6 2) Open the front cabinet. Turn ON the power switch in the front cabinet of the main unit. 3) Turn ON the power switch on the operation panel. ON <State of switch> ONOFF

Related Products and Documents (All in One Printer):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Delfield 4472N-12 Specification sheet delfield/4472n-12-5JI.pdf 25 Jun 2023 4 2.14 Mb
2 Motorola Motosmart Operation & user’s manual motorola/motosmart-44Q.pdf 04 Oct 2022 48
3 Kanguru 1 Operation & user’s manual kanguru/1-YN1.pdf 29 Oct 2023 3
4 Fundex Games Regal 12 Backgammon Instructions fundex-games/regal-12-backgammon-A85.pdf 22 Feb 2023 5 0.31 Mb
5 Weber 54788 Owner's manual weber/54788-C6K.pdf 28 Mar 2023 52 13.47 Mb
6 TCS ISH3230-0140 Instruction manual tcs/ish3230-0140-921.pdf 08 Feb 2023 2

Similar Resources:

  • Lexmark

    W840

    (18 pages)
    Connection GuidePage 1 of 2Connection GuideNote: For local printing, you must install the printer software (drivers) before connecting the USB cable.Installing printer and software for local printing using Windows1 Launch the drivers CD that shipped with the printer.2Click Install Printer and Software.Note: Some Windows operating systems require that you hav …
  • Konica Minolta

    DI2510

    (156 pages)
    Read First1IntroductionSafety InformationPrecautionsAuxiliary FunctionsUtility Mode OperationsAdministrator Management OperationsAppendixDi2510/Di3010/Di3510User Manual[Advanced Operations]www.konicaminolta.net …
  • Canon

    imageCLASS D550

    (116 pages)
    Quick View- Perform Useful TasksNext PageBefore Using the MachineP. 1 - 11Document and Paper HandlingP. 2 - 12CopyingP. 3 - 13Printing from a ComputerP. 4 - 1456789Be sure to read the manual before using the machine.Keep the manual for future reference.Searching the Installation and Connection ProcedureSee the Starter Guide.Using the Scan FunctionsP. 5 - 1Ma …
  • Epson

    EMP-9100

    (20 pages)
    ESC/VP Level 6 Serial Communication Manual (Abridged Edition) 1 of 20ESC/VP Level 6 Serial Communication Manual (Abridged Edition) Ver.3Table of ContentsREVISION STATUS.................................................................................................................................................... 21. OUTLINE ............................... …
  • Ricoh

    Aficio MP C2030

    (96 pages)
    Placing OriginalsCopyingColour CopyingCopier FeaturesAppendix12345Read this manual carefully before you use this machine and keep it handy for future reference. For safe and correct use, be sure to read the Safety Information in "About This Machine" before using the machine.Operating InstructionsCopy Reference …
  • Epson

    Stylus NX420

    (4 pages)
    Start Here 3 Squeeze the edge guide as you slide it all the way to the left. 4 Load letter or A4-size paper against the right edge and behind the tab, with the printable side face up. 5 Slide the edge guide over. Continue with section 6 to choose your connection type.Read these instructions before using your product.1 UnpackFrench control panel sti …

Comments, Questions and Opinions: