Centrality PA168X Operation & User’s Manual

Text of Centrality PA168X User Guide:

• Centrality PA168X, PA168X SIP Phone User Manual (V1.42) Beijing Centrality Communication Inc 37 set handsetout X Set initial volume of handout. X is ranged from 0 through 31. set ringtype X Set types of ring. X is ranged from 0 through 3: 0: ring as ordinary rings in different frequency; 1: do not ring; 2: ring as music saved by user; 3: Set ring used the individualized tone provided by system (need system support). set speakerin X Set initial volume of microphone of the base. X is ranged from 0 through 15. set speakerout X Set initial volume of speaker out. X is ranged from 0 through 31. set service X Set register the SIP proxy server or not. X ranged from 0 through 1. 0: do

• Centrality PA168X, PA168X SIP Phone User Manual (V1.42) Beijing Centrality Communication Inc 46 phone for incoming calls. When it rings, you can receive the call by following methods: ① Use handset: Lift the handset and begin speaking. When the call is over, put the handset back. ② Handset to hand free: While receiving call with handset, press on the keypad and then put down the handset. When the call is over, press again. ③ Hand free: Press to speak to the other party. When t

• Centrality PA168X, PA168X SIP Phone User Manual (V1.42) Beijing Centrality Communication Inc 50 Reserves the right to make changes in technical and product specification without prior notice. PA168X SIP Phone User Manual (V1.42) Copyright© 2003---2005 Beijing Centrality Communication Inc. All rights reserved

• Centrality PA168X, PA168X SIP Phone User Manual (V1.42) Beijing Centrality Communication Inc 42 Set auto-upgrade matching type，X is range from 0 through 5， 0------disable；1------all ；2------ mac；3------ppp id; 4------ account; 5------ phone number。 set upgradeaddr XXX.XXX.XXX.XXX Set IP address or domain name of FTP server supplying upgraded program of PA168X IP phone. set ntsip XXX.XXX.XXX.XXX Set IP address of timeserver. set daylight X Set use daylight or not. X ranged from 0 through 1: 0: do not use daylight;

• Centrality PA168X, PA168X SIP Phone User Manual (V1.42) Beijing Centrality Communication Inc 7 left side of the base. 2． Connect IP phone to Internet: plug the RJ-45 Ethernet cable into the Ethernet Jack. Plug the other end of the cable into HUB switch. 3． Power on IP phone: plug the power cord adapter into the Power Jack. Then plug the other end of the power cord adapter into the appropriate wall outlet. ¾ Configuration Three ways of configuring the PA168X SIP phone are available

• PA168X SIP Phone User Manual (V1.42) Beijing Centrality Communication Inc 48 numbers reservedly. If there is no record, you will hear nothing. ● View received call Click ，then you will hear the record of the received call. Click to turn the number orderly; click to turn the numbers reservedly. If there is no record, you will hear nothing.

• PA168X SIP Phone User Manual (V1.42) Beijing Centrality Communication Inc 27 If you type super password, then you will see: Password : ******** P:\> Above information indicates that IP phone is under setting mode, and then you can set the PA168X IP phone by using the telnet commands. ¾ PA168X Telnet Commands Explanation PA168X Telnet Commands Command Function ? Supply

• PA168X SIP Phone User Manual (V1.42) Beijing Centrality Communication Inc 3 Fig 1.2 PA168X Phone Back Illustration ¾ Function Keys of PA168X IP Phone Introduction: Keys Function Keys Function Local IP With handset hung, press this key to display local IP address on LCD. Missed With handset hung, press this key to review missed number.

• Centrality PA168X, PA168X SIP Phone User Manual (V1.42) Beijing Centrality Communication Inc 9 Fig 2.4 Phone submenu structure Illustration Fig 2.5 Protocol submenu structure Illustration Fig 2.6 other submenu structure Illustration

• Centrality PA168X, PA168X SIP Phone User Manual (V1.42) Beijing Centrality Communication Inc 33 from 0 through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm. set codec4 X Set the priority 4 of the audio compression algorithm. X is range from 0 through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm. set codec5 X Set the priority 5 of the audio compression algorithm. X is range from 0 through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm. set codec6 X Set the priority 6 of the audio compression algorithm. X is range from 0 through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm. set vad X Enable/disabl

• Centrality PA168X, PA168X SIP Phone User Manual (V1.42) Beijing Centrality Communication Inc 49 Appendix Table： PA168X IP phone digital-character key map: Keys Press Once Press Twice Press Thrice Press quartic Press quintic 1 1 . , ?/_ !// 2 2 A/a B/b C/c [ 3 3 D/d E/e F/f ] 4 4 G/g H/h I/i * 5 5 J/j K/k L/l 6 6 M/m N/n O/o # 7 7 P/p Q/q R/r S/s 8 8 T/t U/u V/v 9 9 W/w X/x Y/y Z/z * . 0 0 space :/@ ;/- \ /& # Case change

• Centrality PA168X, PA168X SIP Phone User Manual (V1.42) Beijing Centrality Communication Inc 43 Relevant Usage: load 1 Command exit Syntax description: no keyword and parameter Usage: Exit from Telnet command window without saving the configuration. Relevant usage: None Command write Syntax description: No keyword and parameter Usage: Save the configuration and restart the PA168X IP phone. Command ping Syntax description: ping IP address Usage: ping IP address of other NAT device Relevant usage: In telnet window, input ping xx.xxx.xx.xx（an IP address） and return, then the result will be displayed. If the address is effective,

• Centrality PA168X, PA168X SIP Phone User Manual (V1.42) Beijing Centrality Communication Inc 19  uptech: Use Uptech’s system  keimen: Use Keimen’s system  mediaring: Use Mediaring’s SIP system  italkbb: Use ItalkBB’s SIP system  stanaphone: Use Stanaphone’s SIP system  net2phone: Use Net2phone’s SIP system  Fwd: Free SIP service; please visit www.freeworldialup.com for more information.  Inphonex: Free SIP service; please visit www.inphonex.com for more information.  sipphone: Free SIP service ; please visit www.sipphone.com for more inform

• Centrality PA168X, PA168X SIP Phone User Manual (V1.42) Beijing Centrality Communication Inc 39 If the system has an Outbound Proxy，Set the domain name of SIP proxy server such as xxxx. set nattraversal X X ranged from 0 through 2: 0: do not use NAT traversal. When the log in server and IP phone in the same LAN, or the log in system supports the IP phone working behind the LAN; 1: Use NAT traversal. When the login system does not support IP phone working behind the LAN, With this item selected, please make port mapping on NAT device; 2: stun. set nataddr XXXXX When “nattraversal” is set to “1”;set IP address of NAT device

• Centrality PA168X, PA168X SIP Phone User Manual (V1.42) Beijing Centrality Communication Inc 23  no check: Disable checking firmware tags when upgrading. This is not suggested, because it will increase the risk of upgrading the wrong firmware into the phone. Other settings: Fig 3.6 Other Setting Page ● password: Set the password of the phone. (Default password is 1234). ● upgradetype: Set the auto-upgrade type of the phone.  disable : Disable auto-upgrade .  all: pa168X phone will find matching firmware binary file and configuration file of the ha

• Centrality PA168X, PA168X SIP Phone User Manual (V1.42) Beijing Centrality Communication Inc 34 set jittersize X Set buffer size of RTP package. X is range from 0-32. set 6.3k X With G.7231, set PA168X IP phone to use 6.3K rate or not. X is ranged from 0 through 1: 0: use 6.3K rate; 1: use 5.3K rate. set dialplan X Enable/disable dial plan and dial number. Parameter X ranged from 0 through 4: 0: disable dial plan; 1: enable dial plan; 2: use dial number; 3: use 179XX service.;4: use hotline function. set dialnumber XX When set dialplan value set as 2, please use this command to set dial number. For example, with eTalk card used

• Centrality PA168X, PA168X SIP Phone User Manual (V1.42) Beijing Centrality Communication Inc 38 0: common: disable repaid card or specially system ; 1: use huawei’s system; 2: use ZTE’s system; 3: use harbour’s system; 4: use utstarcom’s system; 5:use uptech system; 6: use keimen’s system; 7: use meidaring’s service; 8: use italkBB service; 9: use stanaphone service; 10: use net2phone SIP service; 11: use fwd(freeworlddialup) service; 12: use inphonex system; 13: use sipphone system;

• Centrality PA168X, PA168X SIP Phone User Manual (V1.42) Beijing Centrality Communication Inc 2 ¾ PA168X IP phone Appearance Introduction: ● PA168X IP Phone Front Illustration (Refer to Fig 1.1): Fig 1.1 PA168X IP Phone Front Illustration ● PA168X IP Phone Back Illustrations(Refer to Fig 1.2 ): Local IP Phone Number Menu/Enter LCD Display Set Missed Received Out Backspace Vol + Vol - Phone book Flash Hold Transfer Redial Speaker Call

• Centrality PA168X, PA168X SIP Phone User Manual (V1.42) Beijing Centrality Communication Inc 10 Fig 2.7 advanced submenu structure Illustration ¾ Configured by WEB Double click icon to open the IE browser. Input the IP address of the phone into address bar ( ), and then input password of the phone into the following page. Fig 3.1 Http Setting

• Centrality PA168X, PA168X SIP Phone User Manual (V1.42) Beijing Centrality Communication Inc 45 ¾ Upgrade PA168X IP phone ¾ Set FTP server FTP server can be supplied by the server provider as well as setup by the users in LAN. Please set the IP address of FTP server. ¾ Prepare Updated program You can ask the server provider for the latest version of program or visit www.aredfox.com to download the latest version. ¾ Operation If you have got the IP address of the FTP server from ISP, please do as follows: a) Use keypad to enter setting mode b) Use keypad to input the IP address of FTP server c) Press , then No19 light will bli

• PA168X SIP Phone User Manual (V1.42) Beijing Centrality Communication Inc 4 speaker，press this key to Increase the volumes of speaker. With pressing “missed” or“received” or “out” and then press this key to turn over the record backward. Enter the menu mode; press this key to turn over the item backward. With handset picked，press this key to decreas

• Centrality PA168X, PA168X SIP Phone User Manual (V1.42) Beijing Centrality Communication Inc 6 ● DHCP：Dynamic Host Configuration Protocol ● PPPoE：PPP Protocol over Ethernet ● DNS：Domain Name Server ● Telnet：Internet's remote login protocol ● FTP：File Transfer protocol ● HTTP：Hyper Text Transfer protocol ¾ Operating requirements: ● Operation temperature: 0 to 50° C (32° to 122° F) ● Storage temperature: -30° to 65° C (-22° to 149° F) ● Humidity: 10 to 90% no

• Centrality PA168X, PA168X SIP Phone User Manual (V1.42) Beijing Centrality Communication Inc 20 URI of the Outbound proxy into “sip proxy” and set the domain name of SIP proxy server into “domain/realm”. The default service port is 5060. If “use service” is not checked, please clear “sip proxy” and “domain/realm”. ● nat traversal: When the IP phone with private IP address need communicate with other IP phones in a different LAN or on Internet, please select an item from dropdown list.  disable: Select this item when the sip proxy server and IP phone in the same LAN, or the sip proxy system supports the IP phone working behind the LAN.  ena

• Centrality PA168X, PA168X SIP Phone User Manual (V1.42) Beijing Centrality Communication Inc 18 Fig 3.5 Protocol Setting ● use service: Enable/disable service by checking/clearing this box. To make calls through SIP Proxy Server, please check this box; otherwise, phone can only make IP-to IP calls. ● register ttl : IP phone will send a keep-alive registration message to SIP proxy server every “register ttl” seconds. The minimum value is 10, maximum value is 65535. Default is 60. ● service type: This option is used to accommodate the miscellaneous requirements of the syst

• Centrality PA168X, PA168X SIP Phone User Manual (V1.42) Beijing Centrality Communication Inc 36 call wait; 1: use call wait. set fwdnumber XXXXXXX Set receiving forwarded calls phone number. XXXX must be an Arabic numeral and no longer than 16 characters set fwdalways X Enable/disable forward all calls. X is ranged from 0 through 1. 0: do not forward all calls; 1: forward all calls. set fwdbusy X Enable/disable forward calls if busy. X is ranged from 0 through 1. 0: do not forward calls if busy; 1: forward call if busy. set fwdnoanswer X Enable/disable forward calls without replying. X is ranged from 0 through 1. 0: do not forward calls without replying; 1: forwa

More Instructions:

Centrality PA168X Configuration manual 07-04-2023 23

DOWNLOAD

Related Products and Documents (IP Phone):

Comparable Devices:

Similar Resources:

• Polycom VSX5000 (23 pages) Page 1 of 23 © Copyright 2006, Oregon State University Extension Service http://extension.oregonstate.edu/esoc/ectu/ Instructional Documents Video Conference >> PolyCom >> VSX 5000 This Document Contains: A Device Description An Installation Guide Instructions for Use Best Practices Troubleshooting Information Contact Information for Mo …

• Panasonic KX-NT553 (3 pages) Unity Connected Solutions – Panasonic KX-NT553/556 Telephone Panasonic KX-NT553/556 Telephone Quick Reference Guide …

• Nortel 2050 (2 pages) Feature operationLegendLegend (continued)Services and Telephone Options menusNote: The Directory button provides access to the Corporate Directory and Personal Directory. For additional information about your IP Softphone 2050, consult the IP Softphone 2050 User Guide.* To use a headset equipped with Bluetooth® wireless technology, you must first configure …

• Genban IP8820 (158 pages) IP Phone Installer Guide IP8820/IP8830/IP8840 SIP (Session Initiation Protocol) GENBAND Call Servers Please read this manual carefully before installation. Retain it for future reference. …

• Polycom VVX 300 SERIES (2 pages) Make a Call1 Li the handset, or press the New Call buon, or press the Speakerphone buon, or press the Headset buon if using a headset. Then:• Dial the number with area code using the keypad; OR• If the person you are calling is in your contacts, press the Contacts buon, use the direconal pad to highlight the contact, press Dial; O …

• Alcatel IP15 (2 pages) Environment This symbol means that your inoperative electronic appliance must be collected separately and not mixed with the household waste. The European Union has implemented a specific collection and recycling system for which producers' are responsible.This appliance has been designed and manufactured with high quality materials and compone …

Comments, Questions and Opinions: