HP Pro Slate 10 EE G1 Maintenance And Service Manual
|
HP Pro Slate 10 EE G1, Rear-facing webcam Description Spare part number 5.0-MP, HD rear-facing webcam with auto-focus (includes cable) 802825-001 Before removing the rear-facing webcam, follow these steps: 1. Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on, and then shut it down through the operating system. 2. Disconnect the power from the tablet by unplugging the power cord from the tablet. 3. Disconnect all external devices from the tablet. 4. Remove the back cover (see
HP Pro Slate 10 EE G1, Performing a system recovery In case of system failure or instability, the tablet provides the following tools to recover your files: ● Windows recovery tools: You can use Windows Backup and Restore to recover information you have previously backed up. You can also use Windows Automatic Repair to fix problems that might prevent Windows from starting correctly. NOTE: If you are unable to boot (start up) your tablet, contact support. Changing the boot device order To change the boot order so that you can boot from an external device: NOTE: An external flash drive is required to perform this procedure. 1. If possible, back up all personal files. 2. Shut down the tablet. 3. Connect the
HP Pro Slate 10 EE G1, Component Spare part number For use in the United States 803030-001 NFC antenna 802832-001 NFC module (includes cable) 802831-001 Screw Kit: For use only on HP Pro Slate 10 EE G1 tablet models 802847-001 For use only on HP Pro Tablet 10 EE G1 tablet models 805304-001 Stylus pen 802822-001 12 Chapter 3 Illustrated parts catalog
HP Pro Slate 10 EE G1, 4 Removal and replacement preliminary requirements Tools required You will need the following tools to complete the removal and replacement procedures: ● Magnetic screw driver ● Phillips P0 screw driver ● Plastic case utility tool Service considerations The following sections include some of the considerations that you must keep in mind during disassembly and assembly procedures. NOTE: As you remove each subassembly from the tablet, place the subassembly (and all accompanying screws) away from the work area to prevent damage. Pla
HP Pro Slate 10 EE G1, Country/region Accredited agency Applicable note number Sweden CEMKO 1 Switzerland SEV 1 Taiwan BSMI 4 The United Kingdom BSI 1 The United States UL 2 1. The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used. 2. The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole grounding type with a NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration. 3. The appliance coupler, flexible cord, and wall plug m
Questions and answers 1. How can the BIOS settings be restored (returned to factory settings)? IMPORTANT: Restore defaults does not securely erase any data on your hard drive. See question and answer 6 for steps to securely erase data. Restore defaults does not reset the Customer Secure Boot key. See question and answer 7 for information about resetting the ke
HP Pro Slate 10 EE G1, 1. Release the ZIF connector (1) to which the sensor board cable is attached, and then disconnect the sensor board cable from the system board. 2. Detach the sensor board cable (2) from the display panel assembly. (The sensor board cable is attached to the display panel assembly with double-sided adhesive.) 3. Detach the sensor board (3) from the display panel assembly. (The sensor board is attached to the display panel assembly with double-sided adhesive.) 4. Remove the sensor board and cable. Reverse this proce
HP Pro Slate 10 EE G1, 11. Detach the WLAN main antenna transceiver (3) from the display panel assembly. (The WLAN main antenna transceiver is attached to the display panel assembly with double-sided adhesive.) 12. Remove the WLAN main antenna cable and transceiver. 13. Disconnect the WLAN auxiliary antenna cable (1) from the WLAN module auxiliary terminal. 26 Chapter 5 Removal and replacement procedures
Grounding guidelines Electrostatic discharge damage Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions. A discharge of s
Index A AC adapter, spare part numbers 11 antenna location 5 removal 23 spare part numbers 7, 23 Antenna Kit, spare part numbers 7, 23 audio, product description 1, 2 audio-in jack 5 audio-out jack 5 B back cover removal 18 spare part number 7, 18 battery removal 19 spare part number 7, 19 buttons power 5 volume down 5 volume up 5 C Cable Kit, spare part number 11 cables,
HP Pro Slate 10 EE G1, a. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. b. Select Main, and then select Reset BIOS Security to Factory Default. c. Follow the on-screen instructions. d. Select Main, select Save Changes and Exit, and then follow the on-screen instructions. 7. How can the Customer Secure Boot Key be reset? Secure Boot is a feature to ensure that only authenticated code can start on a platform. If you enabled Secure Boot
HP Pro Slate 10 EE G1, 2 External component identification Item Component Item Component (1) Power button (10) Micro SD Card Reader slot (2) Microphone (11) Micro SIM slot (3) Front-facing webcam (12) Micro HDMI jack (4) WLAN antenna (13) Micro USB 2.0 port (5) Rear-facing webcam (14) Power light (6) WWAN antenna (15) Power button (7) Volume up button (16) Speaker (8) Volume down button (17) Stylus pen and location (9) Audio-out (headphone)/Audio-in (microphone) jack 5
HP Pro Slate 10 EE G1, 4. Remove the system board (2). Reverse this procedure to install the system board. I/O cover Description Spare part number I/O cover 802821-001 Before removing the I/O cover, follow these steps: 1. Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on, and then shut it down through the operating system. 2. Disconnect the power from the tablet by unplugging the power cord from the tablet. 3. Disconnect all external devices from the tablet. 4. Remove the back cover (see Back cover on page 18). 5. Disconnect the battery cable from the system board (see Battery on page 19). 6. Remove the system board (see System board on page 35). Remove th
HP Pro Slate 10 EE G1, 3. Detach the WWAN auxiliary antenna transceiver (3) from the display panel assembly. (The WWAN auxiliary antenna transceiver is attached to the display panel assembly with double-sided adhesive.) 4. Remove the WWAN auxiliary antenna cable and transceiver. 5. Disconnect the WWAN main antenna cable (1) from the WWAN module main terminal. 6. Release the WWAN main antenna cable from the retention clips (2) built into the display panel assembly. 24 Chapter 5 Removal and replacement procedures
3. Disconnect all external devices from the tablet. 4. Remove the back cover (see Back cover on page 18). 5. Disconnect the battery cable from the system board (see Battery on page 19). Remove the system board: 1. Disconnect the following cables from the system board: (1) GPS antenna cable (2) Front-facing webcam cable (see Front-facing webcam on page 30) (3) Sensor boar
HP Pro Slate 10 EE G1, System board Description Spare part number For use only on HP Pro Slate 10 EE G1 tablet models (all system boards equipped with the Android 4.4.4 operating system): Equipped with an Intel Atom Z3735F 1.83-GHz processor (quad core), a graphics subsystem with UMA memory, 2.0-GB of system memory, 32-GB of system storage, NFC, and WWAN capability 802838-001 Equipped with an Intel Atom Z3735F 1.83-GHz processor (quad core), a graphics subsystem with UMA memory, 2.0-GB of system memory, 32-GB of syste
HP Pro Slate 10 EE G1, 9 Statement of memory volatility The purpose of this chapter is to provide general information regarding nonvolatile memory in HP Business Notebook PCs. This chapter also provides general instructions for restoring nonvolatile memory that can contain personal data after the system has been powered off and the hard drive has been removed. HP Business Notebook PC products that use Intel®-based or AMD®-based system boards contain volatile DDR memory. The amount of nonvolatile memory present in the system depends upon the system configuration. Intel-based and AMD-based system boards contain n
3 Illustrated parts catalog Locating the serial number, product number, and model number The tablet serial number and product number of are located on the tablet back cover. This information may be needed when travelling internationally or when contacting support. 6 Chapter 3 Illustrated parts catalog
HP Pro Slate 10 EE G1, Equipment guidelines Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation. ● When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly against the skin at all times. On grounded mats with banana-plug connectors, use alligator clips to connect a wrist strap. ● When standing, use foot straps and a grounded floor mat. Foot straps (heel, to
HP Pro Slate 10 EE G1, Item Component Spare part number Equipped with an Intel Atom Z3735F 1.83-GHz processor (quad core), a graphics subsystem with UMA memory, 2.0-GB of system memory, 64-GB of system storage, WWAN capability, and the Windows 8 Standard operating system 803373-501 Equipped with an Intel Atom Z3735F 1.83-GHz processor (quad core), a graphics subsystem with UMA memory, 2.0-GB of system memory, 64-GB of system storage, WWAN capability, and a non-Windows 8 operating system 803373-001 Equipped with an Intel Atom Z3735F 1.83-GHz processor (quad core), a graphics subsystem with UMA memor
HP Pro Slate 10 EE G1, 10 Power cord set requirements The wide-range input feature of the tablet permits it to operate from any line voltage from 100 to 120 volts AC, or from 220 to 240 volts AC. The 3-conductor power cord set included with the tablet meets the requirements for use in the country or region where the equipment is purchased. Power cord sets for use in other countries and regions must meet the requirements of the country or region where the tablet is used. Requirements for all countries The following requirements are applicable to all countries and regions: ● The length of the p
HP Pro Slate 10 EE G1, I/O cover ............................................................................................................................................................... 39 6 Using HP PC Hardware Diagnostics (UEFI) ...................................................................................................... 41 Downloading HP PC Hardware Diagnostics (UEFI) to a USB device .................................................................... 41 7 Specifications ............................................................................................................................................. 42 8 Backup and recovery ....................................
DOWNLOAD |
HP CM6040f - Color LaserJet MFP Laser Tablet Reference
CM6040f - Color LaserJet MFP Laser |
HP ProBook 4325s - Notebook PC Tablet Frequently asked questions manual
ProBook 4325s - Notebook PC |
HP Q7829A Tablet Brochure
Q7829A |
HP CM6040f - Color LaserJet MFP Laser Tablet Quick reference manual
CM6040f - Color LaserJet MFP Laser |
HP CM4730 Tablet Operation & user’s manual
CM4730 |
HP 3115m Tablet Technical white paper
3115m |
HP LaserJet 9040/9050 - Multifunction Printer Tablet Installation manual
LaserJet 9040/9050 - Multifunction Printer |
HP LaserJet 4345 - Multifunction Printer Tablet Install manual
LaserJet 4345 - Multifunction Printer |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | True North | TN19 | Installation and operating instructions manual | true-north/tn19-F5K.pdf | 09 Feb 2024 | 20 | |
2 | Sanyo | PLC-WM4500/L - 4500 Lumens | Manual | sanyo/plc-wm4500-l-4500-lumens-Z6X.pdf | 01 Sep 2022 | 78 | 0.49 Mb |
3 | COP-USA | CZ27RC | Operation & user’s manual | cop-usa/cz27rc-Q31.pdf | 07 Jul 2022 | 2 | |
4 | Bradford White | brute elite 125 BLMH | Installation and operation instructions manual | bradford-white/brute-elite-125-blmh-36F.pdf | 07 Apr 2023 | 52 | |
5 | Lennox | EBVSTNM-B | Care and operation instructions manual | lennox/ebvstnm-b-VW9.pdf | 19 Apr 2023 | 32 | |
6 | Whirlpool | MH7115XB | Use and care manual | whirlpool/mh7115xb-G82.pdf | 23 Nov 2023 | 56 | 2.85 Mb |
Alcatel
1English - CQF1F1001AAASafety and Warranty InformationThis device meets applicable national SAR limits of 2.0 W/kg. SAR values can be found on page 7 of this user guide. When carrying the device or using it while worn on your body, either use an approved accessory such as a holster or otherwise maintain a distance of 10 mm from the body to ensure compliance …
PIXI 4 9003X(16 pages) |
MobileDemand
xTablet T7000 QWERTY Keyboard Installation and User’s Guide Last Updated: December 27, 2011 Find the latest updates in the Support section on the MobileDemand website at: www.RuggedTabletPC.com Questions? Call MobileDemand Support at 877-784-4338 Copyright © 2012 MobileDemand, L.C. All Rights Reserved
…
xTablet T7000(7 pages) |
Vantron
VT‐TAB185‐SKLUAllRightsReservedVT‐TAB185‐SKLUUser’sManualChengduVantronTechnology,Ltd.www.vantrontech.com
…
VT-TAB185-SKLU(52 pages) |
Fujitsu
1Fujitsu LifeBook P SeriesBIOS GuideLifeBook P Series Model:P1630Document Date: 10/15/2008Document Part Number: FPC65-4373-01 FUJITSU COMPUTER SYSTEMS CORPORATION
…
P1630 - LifeBook Tablet PC(25 pages) |
Compaq
COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIREDWriter: JAbercrombie Saved by: Lorise Fazio Saved date: 05/22/00 1:31 PMPages: 2 Words: 168 Template: c:\msoffice\templates\portables\ref-ntc.dotPart Number: 198212-001 File name: Notice.docNoticeThe information in this guide is subject to change without notice.COMPAQ COMPUTER CORPORATION SHALL NOT BE …
Wireless LAN 100(65 pages) |
Panasonic
Tablet ComputerModel No. FZ-M1 seriesENGLISHRefer to the OPERATING INSTRUC-TIONS - Basic Guide by downloading from the following URL.OPERATING INSTRUNTIONS - Read Me FirstSafety Precautions .............................................................2Regulatory Information .......................................................6First-time Operation ........ …
FZ-M1(112 pages) |
Fostex Recording Equipment DC-R302Recording Equipment #E1L28M DC-R302, 10 |
Tesoro Keyboard EXCALIBUR SEKeyboard PDF Quick start manual EXCALIBUR SE, 16 |
Tecovision LCD TV LED19DHRBJBDPDF User Guide (@BF1K9Y), Tecovision LED19DHRBJBD LCD TV (Wednesday 24-01-2024) LED19DHRBJBD, 57 |
VALERA Other 1822PDF User Manual (@92F331), VALERA 1822 Other (31/10/2023) 1822, 2 |
Ricoh Printer VT1730VT1730 (Printer ePDF Manual, #V12A1X) VT1730, 63 |
Patton electronics Modem 1082Patton electronics Modem 1082 Operation & user’s manual 1082, 32 |
AT&T Cordless Telephone 1485Cordless Telephone Operation & user’s manual (AT&T 1485) 1485, 50 |
Dialogic Computer Hardware D/21HDialogic D/21H User Manual (Operation & user’s manual), @2HNCWM D/21H, 2 |
LG Monitor MU-42PZ90XCLG Monitor Owner's manual (File: lg-mu-42pz90xc-owner-s-manual-36, 02nd Feb 2024) MU-42PZ90XC, 36 |
Planet IP Camera ICA-HM317ICA-HM317 (IP Camera ePDF Manual, #5U92J1) ICA-HM317, 70 |
Steelcraft Stroller AX108Steelcraft Stroller Instruction booklet (File: steelcraft-ax108-instruction-booklet-18, 08/11/2023) AX108, 18 |
Samsung TV CL21K30MQ6XXAO#4R8Y57 CL21K30MQ6XXAO: Samsung TV Owner Documentation CL21K30MQ6XXAO, 23 |