KIP 770K Operation & User’s Manual

Text of KIP 770K User Guide:

• KIP 770K, Chapter 2 Basic Operation 2-5 2. 3 Replacing Roll Media 1. Open Roll Deck Cover (1). Holding both Flanges (2), lift and remove a roll media or an empty roll core (3). 2. Raise the green lever (4) on Flange (2). Remove both Flanges (2) from the roll core (3). 3. Move the right Slide Guide (5) to match your roll media’s width. The right and left Slide Guides move together. NOTE A media mis-feed tends to occ

• KIP 770K, Chapter 1 Before Use 1-16 Pre-printed Extremely slippery Extremely sticky Extremely thin and soft OHP Film 1. 7. 2 Keeping the paper in the custody Keep the paper in the custody taking care of the following matters. 1. Do not expose the paper to the direct sunlight. 2. Keep the paper away from high humidity. (It must be less than 70%) 3. Put the paper on a flat place 4. If you will keep the paper in the custody, which you have already unpacked, put it into the polyethylene bag to avoid the humidity.

• KIP 770K, Chapter 1 Before Use 1-10 1. 5. 2 Rear view 7: behind No. Name Function 1 Toner Cover Open here to access toner supply system. 2 Original Guide These trays catch the original ejected from the Scanner Unit. 3 LAN Port Connect the LAN Cable to connect the KIP 770 to the network. (Do not connect a telephone line) 4 USB Port Service Use, 5VDC max. 5 Breaker It is possible to shut off supplying the AC power. 6 Inlet Socket Connect the Power Cord here. 5 6 3

• KIP 770K, (2) Safety Warnings The following warnings are very important in order to safely use this product. These notes are important in preventing danger to the operator or operation of the printer. The following symbols are found throughout the USER’S Manual and have the following meaning: WARNING This WARNING mark means that there is a possibility of death or serious injury if you ignore or do not follow the said instruction.

• KIP 770K, Chapter 1 Before Use 1-3 1. 2 Originals Prohibited from Duplication It is not necessarily allowed to copy every kind of original. You may be punished by the law if only you possess the copy of some kind of original. We recommend you to consider enough before you copy such original. [Originals prohibited from copying by the law] 1. It is not allowed to copy Currency (Bill, Money, Bank Note, etc.), Government issued Negotiable Instruments (National Bonds, Security, Loc

• KIP 770K, Chapter 3 Error Correction 3-16 3. 2. 3 Upper Unit (Front Cover Open) Holding the rear side of the Scanner Cover, close the Upper Unit securely to clear "Front Cover Open". 3. 2. 4 Fuser Cover (Fuser Cover Open) Close the Fuser Cover securely to clear "Fuser Cover Open". Upper Unit NOTE There is an interlock switch of the Upper Unit on both sides. In case that "Door

• Chapter 2 Basic Operation 2-19 2. 10 Dehumidifying Roll Media (Option) If the roll paper is extremely humidified, it may cause several kinds of defective print. Defective prints you will experience most will be “crease of paper” and “loss of image”. Turn on the Dehumidify Heater if the room air has too much humidity (65% or highe

• Chapter 2 Basic Operation 2-3 3. The User Interface (UI) starts operating, and displays the following Screen in one minute. "Warming Up" is displayed in the status indication while warming up. The UI screen may vary depending on your system configuration. (Shown with available options) 4. &qu

• KIP 770K, Chapter 4 Maintenance 4-6 3. Gently wipe Sensors (2) with a dry cotton bud. 4. Gently press Scanner Unit down and firmly close it. NOTE Do not use water, organic solvent, glass cleaner or antistatic spray for cleaning. NOTE Press down Scanner Unit on both side to close it. Do not close it by pressing only one side down. 2 2 2 2 2 2 2

• KIP 770K, (5) POWER CORD INSTRUCTION The installation of (or exchange to) a power plug which fits in the wall outlet of the installation location shall be conducted in accordance with the following: WARNING Select a power plug which meets the following criteria; - The plug has a voltage and current rating appropriate for the product’s rating marked on its name plate. - The plug meets regulatory requirements for the area. - The plug is provided with a grounding pin or terminal. If the appropriate plug does not fit the wall outlet in the installation, the customer shall install an appropriate outlet. Connector Type: Configuration Stan

• KIP 770K, Chapter 3 Error Correction 3-10 6. Put your hands on the rear rim of the scanner unit just as you hold the Upper Unit. Push the entire unit down to the arrow direction. Hold here Hold here

• KIP 770K, (1) Thank you for purchasing the Multi-Function Printer KIP 770. This Hardware Operation Guide contains functional and operational explanations for the KIP 770. Please read this Hardware Operation Guide carefully before using the printer. Please keep this Hardware Operation Guide for future reference. 1. When this product is installed in North America. This product complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This product may not cause harmful interference, and (2) this product must accept any interference received, including in

• KIP 770K, Chapter 3 Error Correction 3-19 3. 4 Service Call Error If an error with significant effect on the printer occurs, the printer stops the operation and indicates a related Customer Engineer Call Error Code (or description, and its equivalent internal code) on the UI screen. Call the service staff immediately as these problems can be fixed by a well trained technician only. Before calling the service staff, try to turn on/off the Printer. If “Service Call Error” is indicated again, turn off the machine, unplug

• KIP 770K, Chapter 2 Basic Operation 2-18 2. 9 Canceling Sleep Mode The KIP 770 has two Sleep Modes to reduce the power consumption. The KIP 770 will enter Sleep Mode after a certain period of inactivity. In the default setting; • Warm Sleep Mode will start after a 15 minute of inactivity in order to reduce the power supply for Fuser Unit. • Cold Sleep Mode will start after a 60 minute of inactivity to stop the power supply for Fuser Unit and some other components. Sleep Mode is canceled and the machine gets ready when; • the m

• Chapter 1 Before Use 1-7 Subject Specification Media source 1 Roll Deck (3” / 2” core roll* ) Manual Feeder (single cut sheet) Paper Tray (multiple cut sheet, option) Media (Recommended Roll Media) - US model: Bond : 64g/m 2 to 80g/m 2 , US Bond (20# Bond) Vellum : US Vellum (20# Vellum) Film : 4MIL (4Mil-2 Xero Film) - Europe/Asia model:

• KIP 770K, Chapter 1 Before Use 1-9 1. 5 Appearance 1. 5. 1 Front view 7 7 2 2 8 No. Name Function 1 Main Switch You can turn on/off the KIP 770. 2 Original Guides Feed the original under the Scanner Unit along the Original Guides. 3 User Interface This is a Touch Screen, and many kinds of user operation are available. PLEASE DO NOT push the LCD area too strong. 4 USB port Your USB flash memory storage can be installed here. 5VDC

• KIP 770K, Chapter 3 Error Correction 3-6 3. 1. 3 Media Feed Section Jam (Registration Mis-feed) 1. Press down the blue levers (1) on both sides to unlock and open the Upper Unit. 2. Remove the mis-feed media. 1 1 Media Feed Section - Registration Mis-feed

• KIP 770K, Chapter 3 Error Correction 3-13 7. Open the Roll Deck Cover. Rewind the roll onto the media core. 8. Rotate the roll media in the arrow direction and insert the leading edge of the roll media to the media path until it touches the feeding rollers (4). After that, the leading edge will automatically go into the roll media’s wait position. 9. Close the Roll Deck Cover. 4

• KIP 770K, Chapter 2 Basic Operation 2-9 2. 4 Initial Cut 1. Open the Manual Feeder Table (1). 2. Press the green button (2) on the right. 3. The leading edge of the roll media is automatically transported and cut off. Remove the portion of the media (3) and close the Manual Feeder Table (1). 1 2 3 Reference (1) Initial Cut is a function to trim the roll media with its leading edge cut off. (2) Initial Cut becomes available while t

• KIP 770K, Chapter 3 Error Correction 3-9 3. Press down the blue levers (3) on both sides to unlock and open the Upper Unit. 4. Remove the mis-feed media. 5. Close the Exit Door. 3 3

• KIP 770K, Chapter 1 Before Use 1-2 1. 1 Installation Requirements The following conditions are required for the installation of the equipment. 1. Power source should be rated as: U.S.A: 120V +/-10%, 50/60Hz, 15A or higher Europe: 220-240V +6% or -10%, 50/60Hz, 10A or higher 2. The equipment must be on a dedicated circuit. 3. The outlet must be near the equipment and easily accessible. I Norge: Kan kobles til IT strøm distribusjonssystemer. 1. Make sure to connect this equipment to a properly grounded outlet. 2. The outlet shall be ins

• Chapter 4 Maintenance 4-5 4. 1. 2 Sensor If Sensors are dirty, the original may be detected incorrectly. Perform cleaning or as needed. 1. Turn off KIP 770. 2. Lift up both sides (1) of the Scanner Unit. NOTE For ease of visual check, this document shows the Upper Unit fully open (not actual wide). 1 1

• KIP 770K, Chapter 4 Maintenance 4-1 Chapter 4 Maintenance page 4. 1 Scanner Unit 4- 2 4. 1. 1 Scan Glass, Feed Roller, Guide Plate 4- 2 4. 1. 2 Sensor 4- 5 4. 2 Touch Screen 4- 7

• KIP 770K, Chapter 1 Before Use 1-8 1. 4. 3 Scanner part Subject Specification Scanning method Contact Image Sensor (CIS) (5 pieces of A4 sized CIS) Light source LED (R/G/B) Setting of original Face up Starting point of scan Center Scan width Max: 914.4mm / 36” Min : 210mm Scan length Max: 6,000mm / 19.7ft (Including the margin area) (If the print is longer than 6,000mm, its image quality or the reliability of paper feeding is not guaranteed.) Min : 210mm / 8.5” (Including the margin area) Margin area 3mm from leading, trailing and both side edges Optical resolution 600dpi Digital resolution 200 / 300 / 400 / 600 dpi

• KIP 770K, (3) WARNING 1. The Power source should be as follows: In U.S.A. : 120V plus/minus10%, 50/60Hz, 15A or higher In Europe : 220-240V plus6% or minus10%, 50/60Hz, 10A or higher 2. Use a circuit with a dedicated breaker. 3. Install the product as close to the wall outlet as possible. 4. If you wish to move the printer, ple

• KIP 770K, Chapter 2 Basic Operation 2-4 2. 2 Turning off KIP 770 1. There is a Power Switch on the right side of KIP 770. Press its “ ” side to turn off the KIP 770. CAUTION The KIP 770 print engine and UI appear to be shut down when you turn off KIP 770. However, the controller PC embedded inside the KIP 770 is still operating and will shutdown in approximately two minutes after Power Switch operation. Do not unplug the KIP 770 before the co

• KIP 770K, Chapter 4 Maintenance 4-7 4. 2 Touch Screen 1. Wipe the Touch Screen with a dry cloth. NOTE Do not use water, alcohol, organic solvent and glass cleaner for the cleaning.

• Chapter 3 Error Correction 3-4 Reference If your roll media’s end is not fixed to the core (by glue or a tape), a small portion of the media may remain in the media path of the Roll Deck at a roll empty. The printer does not show any mis-feed error code against the portion. So please check for the p

Related Products and Documents (All in One Printer):

Comparable Devices:

Similar Resources:

• Lexmark T632 (345 pages) Lexmark™ T63x(including Lexmark T630, Lexmark T632, Lexmark T634)4060-xxx(including 4060-000, 4060-010, 4060-200,4060-210, 4060-400, 4060-410)• Table of Contents• Start Diagnostics• Safety and Notices•Trademarks• IndexLexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or othe …

• Lexmark 734de - X Color Laser (1 pages) Information guideHelp menuThe Help menu consists of a series of Help pages that are stored in the multifunction printer (MFP) as PDFs. They containinformation about using the printer and performing various tasks, including copying, scanning, and faxing.English, French, German, and Spanish translations are stored in the printer. Other translations are availab …

• Brother MFC-J6945DW (9 pages) Skip to contentManuals+User Manuals Simplified.brother Inkejt Printer User GuideHome » Brother » brother Inkejt Printer User Guide MFC-J6945DW / MFC-J6947DWQuick Setup GuideRead the Product Safety Guide first, then read this Quick Setup Guide for the correct installation procedure. The latest manuals are available at the Brother Solutions Center: support. …

• Ricoh Aficio MP 9000 (232 pages) Paper type: Wood Free 80g/m2, Paper Thickness=100 µm // Pages in book=228 // Print scale=81%Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 11.400001 mmOperating Instructions Security ReferenceB2357900 Operating Instructions Security ReferenceOperating InstructionsSecurity ReferenceRead this manual carefully before you use thi …

• Brother HL-1030 (123 pages) Brother LaserskriverHL-1030/1240/1250BruksanvisningenLes denne håndboken nøye før du tar i bruk skriveren. Du kan når som helst skrive ut ellerlese denne håndboken fra CD-ROMen. Oppbevar CD-ROMen på et hensiktsmessig sted slikat det hele tiden er lett å finne den og å slå opp i den. …

• Epson CX7300 (159 pages) EPSON Stylus CX7300/CX7400/DX7400 NX200/TX200/TX203/TX209 SX200/SX205 EPSON Stylus CX8300/CX8400/DX8400 NX400/TX400/TX405/TX409 SX400/SX405Color Inkjet PrinterSEMF07-001SERVICE MANUALConfidential …

Comments, Questions and Opinions: