Air Live POE-FSH808AT Operation & User’s Manual

Text of Air Live POE-FSH808AT User Guide:

• Appendix A: Product Specifications AirLive POE-FSH808AT User’s Manual 52 Led Indicators Per Port: Link/Act, PoE Act/Status Per Unit: Power Power Input 100~240V/AC, 50~60Hz Power Output 48V/DC Per Port Output – 30 W Max Per Port 8 Port total 130W Power Consumption 130 Watts (Max) for PoE; Temperature Operating:0 to 45 ℃ Storage

• Air Live POE-FSH808AT, 4. Web Management AirLive POE-FSH808AT User’s Manual 44  Port No: The port ID. It cannot be changed. Aggregations mean any configured trunk group.  Root Path Cost: This parameter is used by the STP to determine the best path between devices. Therefore, lower values should be assigned to ports attached to faster media, and higher values assigned to ports with slower media. Set the RSTP path cost on the port. Number between 0 - 200000000. 0 means auto generated path cost.  Priority: Show the value of the Port Priority. Ex: 0x80 is 128.

• 4. Web Management AirLive POE-FSH808AT User’s Manual 45  Loopback Detection Function: This column allows you to enable or disable Loopback Detection function.  Auto Wake Up: Once the Loopback Detection function is running, the ports maybe disabled to avoid the loop. The Auto Wake Up allows you to activate the port after Time Interval passed. 

• Air Live POE-FSH808AT, 4. Web Management AirLive POE-FSH808AT User’s Manual 29 4.6.1 VLAN Mode You may select the VLAN Mode of the switch. Port-based VLAN is for separating traffic only on this single switch. There is no handover of network traffic within VLAN groups to other switches. For the handover to other switches use Tag Based VLAN. In VLAN Mode you can switch from Tag to Port Based VLAN. Port Based VLAN is the default mode. After having switched to Tag Based VLAN Mode, the screen changes. On this screen you can now define and configure your Up and Downlink ports. These are important since here the handover between the switches o

• 4. Web Management AirLive POE-FSH808AT User’s Manual 47  Member: This column allows you to select the member Ports.  Status: This column allows you to Enable/Disable the Trunk Group.  Type: This column allows you to choose Static Trunking or Dynamic LACP Trunking. After Select the LACP Trunk type, the following parameters can be configured. Please

• Air Live POE-FSH808AT, 4. Web Management AirLive POE-FSH808AT User’s Manual 18 Menu Bar On the left side of the screen is the Menu bar where you and click to configure management functions. Most configuration functions are under the “Administrator” menu. We will explain the menu items in the remaining section of this chapter. Top Switch Image The switch’s image on the upper portion of the screen gives the quick overview of the port connection status. When a port is plugged in, the switch’s image will show a “plug” on the corresponding port. 4.4 Administrator There are many management functions can be set or pe

• Air Live POE-FSH808AT, 2. Installation of the Switch AirLive POE-FSH808AT User’s Manual 8  The relative humidity in the location should not exceed 90% non-condensing humidity.  The distance between the RJ-45 port and the standard network interface should not exceed 100 meters.  Adequate space should be allowed in front of all the ports, so that each port is easily accessible for cable connections.  Leave at least 10cm(4 inch) of space around the switch to allow heating dissipation 2.4 Rack Mounting The POE-FSH808AT can be mounted on a standard size 19-inch rack, which can in turn

• Air Live POE-FSH808AT, 2. Installation of the Switch AirLive POE-FSH808AT User’s Manual 11 2.8 Reset to Default When you forgot your IP or password, please use the reset button for the factory default setting? Please take the following steps to reset the Web Smart Switch back to the original default: Step 1. Turn on the POE-FSH808AT. Step 2. Press and hold the reset button continuously for 10 seconds and release the reset button. Step 3. The switch will reboot for 5 seconds and the configuration of switch will back to the default setting. Key in the user ID and the password to pass the authentication; t

• Air Live POE-FSH808AT, 4. Web Management AirLive POE-FSH808AT User’s Manual 50  VLAN Uplink:  Purpose: This switch does not implement Independent VLAN (IVL) MAC address table, it utilizes VLAN uplink to emulate the function of IVL. An independent VLAN MAC address table is based on both the source MAC address and the VLAN. In some application, if the Ethernet switch cannot build the separate MAC address table for different VLANs, there will be a conflict of MAC address table. To solve this problem, the switch controller utilizes the VLAN Uplink port to emulate the usage of Independent VLAN MAC Address Table.  VLAN Uplink Setting: If VL

• Air Live POE-FSH808AT, 4. Web Management AirLive POE-FSH808AT User’s Manual 24  Current Status: Displays the status of each ports. This field indicates the port 9 is link up and run as 1G Full, Flow Control Enabled.  Current Status: Displays current port status.  Setting Status: Displays current status. Click "Update" to have the configuration take effect. 4.5.2 Port Mirroring The port mirroring function is accomplished by setting the following items.

• Air Live POE-FSH808AT, Table of Contents AirLive POE-FSH808AT User’s Manual iii Table of Contents 1. Introduction .............................................................................................. 1 1.1 Overview............................................................................................ 1 1.2 Guide to the Chapters ........................................................................ 2 1.3 Quick Setup ....................................................................................... 2 1.4 Installation Steps ........................................................

• Air Live POE-FSH808AT, 4. Web Management AirLive POE-FSH808AT User’s Manual 13 The POE-FSH808AT can be configured by web based interface, including administrator, port management, VLAN setting, per port counter, trunk setting, QoS setting, security filter, configuration/ backup/recovery, miscellaneous, log out, and so on. The device based smart switch supports main stream browsers, such as IE, Firefox and Chrome…etc to configure the device function. All functions are illustrated below. 4.

• Air Live POE-FSH808AT, Copyright and Disclaimer AirLive POE-FSH808AT User’s Manual i Copyright & Disclaimer No part of this publication may be reproduced in any form or by any means, whether electronic, mechanical, photocopying, or recording without the written consent of OvisLink Corp. OvisLink Corp. has made the best effort to ensure the accuracy of the information in this user’s guide. However, we are not liable for the inaccuracies or errors in this guide. Please use with caution. All information is subject to change without notice All Trademarks are properties

• Air Live POE-FSH808AT, 4. Web Management AirLive POE-FSH808AT User’s Manual 17 On the Switch  On the IP setting, set the gateway to Router’s LAN port address 192.168.0.254.  Please make sure the subnet mask is the same as the router’s. On the Router  Go to router’s Virtual Server setting and open the Web port (TCP Port 80) to the switch’s IP address 192.168.0.200.  If your router require enter the beginning and ending Port (from PortX to PortX), enter 80 for both. Now the Remote PC will be able to access your switch by entering “201.100.1.5” in

• Air Live POE-FSH808AT, 2. Installation of the Switch AirLive POE-FSH808AT User’s Manual 9 Attaching the Switch to a 19-inch rack 2.5 Desktop Installation The POE-FSH808AT has four rubber pads attached on each corner of its underside. These pads serve as cushioning against vibration and prevent the switch from sliding off its position. They also allow adequate ventilation space when you place the switch on top of another device. Desktop installation  The location you choose to install your switch and the way you configure your network may greatly affect its performance. Pl

• Air Live POE-FSH808AT, 4. Web Management AirLive POE-FSH808AT User’s Manual 20 User can configure the IP settings, Subnet Mask, Gateway as below:  IP address: Manually assign the IP address that the network is using. The default IP is 192.168.2.1  Subnet Mask: Assign the subnet mask to the IP address.  Gateway: Assign the network gateway for industrial switch. If you change the IP address of this switch and then press Update. It will show “update successfully” then press Reboot button. It will

• 4. Web Management AirLive POE-FSH808AT User’s Manual 23  Tx/Rx-Ability: Enable or Disable. The default value is "Enable". Being set as "Enable", the port can Transmit and Receive packet without any problem. After changed to "Disable", the selected ports cannot access the network anymore.  Aut

• Air Live POE-FSH808AT, 4. Web Management AirLive POE-FSH808AT User’s Manual 25  Destination port: Theoretically it’s possible to set more than one destination port in a network. Actually the port mirroring function will lower the network throughput, and therefore it’s recommended to set “only one” destination port in a network.  Monitored packets: i. Disable: means this function is disabled. ii. RX: means copy the incoming packets of the selected source port to the selected destination port. ii

• Air Live POE-FSH808AT, 4. Web Management AirLive POE-FSH808AT User’s Manual 26 Example: Type 5 for both Tx and Rx Rate and select the High as speed base for port 1 and port 9. The actual rate for port 1 (Fast Ethernet) is "1280", for port 9 (Gigabit Port) is 10240. You could see the table is updated as below. 4.5.4 Broadcast Storm Control The switch implements a broadcast storm control mechanism. Tick the check boxes to have them beginning to drop incoming broadcast packets if the received broadcast packet counts reach th

• Air Live POE-FSH808AT, 2. Installation of the Switch AirLive POE-FSH808AT User’s Manual 5 2 2. Installation of the Switch This chapter provides the detailed instructions for installation of the switch. For concise installation instruction, the previous chapter’s “Quick Setup” section provides all the important information including IP address, password, and LED table for user’s reference. 2.1 Unpack the Package Before you begin the installation of POE-FSH808AT Management Switch, make sure that you have all the necessary accessories that come with your package. Follow the

• Air Live POE-FSH808AT, 4. Web Management AirLive POE-FSH808AT User’s Manual 37  =Enable High Priority. After Enabled High Priority, the following enabled Port Based parameter will become High Priority.  Port Base: The selected port equipped with High Priority. The non-selected port is Low priority. A packet received by a high priority port is handled as a high priority packet.  VLAN Tag: The switch follows the VLAN tag of the incoming packets to forward traffic. VLAN Tag priority: high priori

• Air Live POE-FSH808AT, 4. Web Management AirLive POE-FSH808AT User’s Manual 49  Output Queue Aging Time:  Purpose: This function is used to avoid the traffic jam on one port will not cause the congestion of other ports. In some application, for example the IPTV Multicast communication, the multicast stream is continuously generating from the source port, the client port may be congested because of the limited bandwidth or slow network processing ability. Then, the Pause frame of Flow Control will be generated once the packet buffer i

• Air Live POE-FSH808AT, 4. Web Management AirLive POE-FSH808AT User’s Manual 28  Port: The port number.  Enable: Enable PoE feature of the specific ports. The default value is OFF for all ports. , after enabled, the PoE output power is ON, the LED is forced to ON.  Output Power: The output power of the port. It is the power consumption of the connected device.  PoE Class: The PoE class of the connected port. 4.6 VLAN Setting A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain, which would allow you to isolate network traffic, so only the members of the same VLAN will receive traffic from the ones of th

• Air Live POE-FSH808AT, Appendix A: Product Specifications AirLive POE-FSH808AT User’s Manual 51 A Appendix A: Product Specifications Standards IEEE 802.3 10BaseT IEEE 802.3u 100BaseTX IEEE 802.3x Flow Control IEEE 802.3ad Trunk (Link Aggregation) IEEE 802.1q VLAN (Port Based and Tag Based) IEEE 802.1p Class of Service, Priority Protocols IEEE 802.1x IEEE 802.1d Spanning Tree Protocol IEEE 802.1w Rapid Spanning Tree Protocol Features Number of Ports: 8 passive Power over Ethernet Ports MAC Addres

Related Products and Documents (Network Router):

Comparable Devices:

Similar Resources:

• Allnet ALL0276 (86 pages) Multi-Function 802.11g Wireless Router 802.11g/802.11b Wireless Access Point Broadband Internet Access 4-Port Switching Hub User's Guide …

• SMC Networks SMCWBR14-G2 (2 pages) SMCWBR14-G2 Barricade™ 802.11g 54Mbps Wireless RouterEnglish: Quick Installation GuideČesky: Rychlý průvodce instalacíSlovensky: Rýchly sprievodca inštaláciouMagyar: Gyors telepítési útmutatóPolski: Podręcznik szybkiej instalacjiEnglish:Please connect your broadband modem to the router's WANport and your PC to one of the LAN ports by wi …

• Patton OnSite 2603 (6 pages) 12 SmartNode 5300 Quick Start GuideNOTES_______________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ …

• GE MDS 4710M (6 pages) MDS Master Station Setup Guide 05-6398A01-GB, Rev. A MDS Master Station Setup Guide 1 INTRODUCTION The MDS Master Station serves as a central station in a multiple ad-dress system (MAS) wireless network. It provides long range, duplex (or simplex) communication between a control point and associated re-motes. It is fully redundant for mission-critical a …

• LevelOne GEU-0807 (17 pages) 1 GEU-0807 8-Port Gigabit Ethernet Switch Quick Installation Guide English Deutsch Français Español Nederlands Dansk Italiano Ελληνικά Português Svenska Slovenščina 繁體中文 한국어 Русский Polski …

• D-Link DIR-826L (3 pages) DIR-826LCloud Router 2000Wireless N600 Dual Band Gigabit Router with Cloud Services600NDUALBANDWirelessly access your saved media from any USB driveDual band performance for video streaming and gamingControl and monitor your network from anywhere with cloud servicesDual Band Performance for video streaming and gamingControl and monitor your network from a …

Comments, Questions and Opinions: