KOLFF Black 1K Operation & User’s Manual
|
-8- The LCD Display Display Function Input Information Indicates the input Line voltage value, which could be displayed from 0 to 999Vac Indicates the frequency value of input Line voltage, which could be displayed from 0 to 99Hz Indicates the input Line current value, which could be displayed from 0 to 99.9A Output Information Indicates the UPS output voltage value, which cou
KOLFF Black 1K, -6- 3. Introduction This On-Line-Series is an uninterruptible power supply incorporating double-converter technology. It provides perfect protection specifically for Novell, Windows NT and UNIX servers. The double-converter principle eliminates all mains power disturbances. A rectifier converts the alternating current from the socket outlet to direct current. This direct current charges the batteries and powers the inverter. On the basis of this DC voltage, the inverter generates a sinusoidal AC voltage, which permanently supplies the loads. Co
-9- Indicates the frequency value of the UPS output voltage, which could be displayed from 0 to 99Hz Indicates the UPS output current value, which could be displayed from 0 to 99.9A Load Information Indicates the load or the UPS output is short and the UPS would shut down Indicates the load is over the SPEC range Indicates the load percent, and the lowest grid rep
-26- 10.3 Typical stored energy time (Typical values at 25°Cin minutes:) Model No. 100 % Load 50 % Load 1K 5 14 2K 9 21 3K 5 15 10.4 Dimensions and weights Model No. Dimensions WDH (mm) Net Weight (kg) 1K 145400220 14 1KS 145400220 7 2K 192460340 34.5 2KS 192460340 15 3K 192460340 35.5 3KS 192460340 16
KOLFF Black 1K, -18- 6.5 Abnormal mode In abnormal mode such as Bus fault etc., the corresponding fault code would be shown to indicate the operating mode of the UPS. And some warning words could also be shown, for example “short!” would be shown when the load or the UPS output is short and the UPS is in inverter fault mode.
KOLFF Black 1K, -11- 5. Connection and operation 5.1 Inspection: Inspect the packaging carton and its contents for damage. Please inform the transport agency immediately should you find signs of damage. Please keep the packaging in a safe place for future use. Note: Please ensure that the incoming feeder is isolated and secured to prevent it from being switched back on again. 5.2 Connection: (1) UPS Input Connection If the UPS is connected via the power cord, please use a proper socket with protection against electric current, and pay attention to the capacity of the socket: over 10A for 1K(S) & 2K, over
KOLFF Black 1K, -2- 1.2 Operation Do not disconnect the mains cable on the UPS or the building wiring socket (grounded shockproof socket) during operation as this would remove the ground to the UPS and of all connected loads. The UPS features its own, internal current source (batteries). You may be electric shock when you touch the UPS output sockets or output terminal block even if the UPS is not connected to the building wiring socket. In order to fully disconnect the UPS, first press the Standby button, then disconnect the mains lead. Ensure that no liquid or other foreign objects can enter the UPS. The UPS can be operated by any individuals with
KOLFF Black 1K, -12- Besides output sockets,2KS and 3K/3KS has the terminal block available for output as well. The wiring configuration is shown as the following procedure: a) Remove the small cover of the terminal block b) Use AWG14 or 2.1mm 2 wires for wiring configuration c) Upon completion of the wiring configuration, please check whether the wires are securely affixed. d) Put the small cover back to the rear panel. (3) Computer Connection: Connect your computer to the outlet sockets of the UPS system following the above diagram. 5.3 Bat
KOLFF Black 1K, -27- 11. Communication port 11.1 RS232 Interface The following is the pin assignment and description of DB-9 connector. Pin # Description I/O 2 TXD Output 3 RXD Input 5 GND Input 11.2 AS400 Interface (Option) Except for the communication protocol as mentioned above, this series UPS has AS400 card (an optional accessory) for AS400 communication protocol . Please contact your local distributor for details. The following is the pin assignment and description of DB-9 connector in AS400 card. Pin # Description I/
KOLFF Black 1K, Please comply with all warnings and operating instructions in this manual and on the unit strictly. Save this manual properly. Do not operate this unit before reading through all safety information and operating instructions carefully.
KOLFF Black 1K, -25- 10. Technical data 10.1 Electrical specifications INPUT Model No. 1K(S) 2K 2KS 3K(S) Phase Single Frequency (46~54)/(56~64) Hz Current(A) 7A 9A 12A 16A OUTPUT Model No. 1K(S) 2K(S) 3K(S) Power rating 1kVA/0.7kW 2kVA/1.4kW 3kVA/2.1kW Voltage 208/220/230/2401 2%VAC Frequency 50/6010.2Hz (Battery mode) Wave form sinusoidal Derating 10% when the output voltage is adjusted to 208VAC BATTERIES Model No. 1K 2K 3K Number and type 312V 7.2Ah 812V 7.2Ah 812V 7.2Ah 10.2 Operating Environment Ambient Temperature 0 o C to 40 o C Operating humidity < 95% Al
KOLFF Black 1K, -4- 1.6 Standards * Safety IEC/EN 62040-1-1 *EMI Conducted Emission..........................:IEC/EN 62040-2 Category C1 Radiated Emission.............................:IEC/EN 62040-2 Category C1 Harmonic Current...............................:IEC/EN 61000-3-2 Voltage Fluctuation and Flicker..........:IEC/EN 61000-3-3 *EMS ESD...................................................:IEC/EN 61000-4-2 Level 4 RS.....................................................:IEC/EN 61000-4-3 Level 3 EFT....................................................:IEC/EN 61000-4-4 Level 4 SURGE.............................................:IEC/EN 61000-4-5 Level 4 Low Frequency Signals.....................:IEC/
KOLFF Black 1K, -24- 9. Maintenance 9.1 Operation The UPS system contains no user-serviceable parts. If the battery servicelife(3~5yearsat25°C ambient temperature) has been exceeded, the batteries must be replaced. In this case please contact your dealer. 9.2 Storage If the batteries are stored in temperate climatic zones, they should be charged every three months for 1~2 hours. You should shorten the charging intervals to two months at locations subject to high temperatures.
KOLFF Black 1K, -7- 4. Panel description The Display Panel Switch Function ON-Button Turn on UPS system: By pressing the “ON” button the UPS system is turned on. Deactivate acoustic alarm: By pressing this Button an acoustic alarm can be deactivated. OFF-Button When mains power is normal, the UPS system switches to No output or Bypass mode by pressing “OFF” button, and the inverter is off. At this moment, if Bypass is enabled, then the output sockets are supplied with voltage via the bypass if the mains power is available. Select-Button I
-10- Indicates the UPS is working in bypass mode, the load is directly supplied by the input power through bypass Indicates the UPS is working in no output mode Indicates the UPS is working in line mode Indicates the UPS is working in battery mode or battery test mode Indicates the UPS is working in fault mode Indicates some warnings occur which need be attention UPS setti
KOLFF Black 1K, -23- The status indicates the UPS is in battery mode, and audible alarm sounding every 1 beep in every 4 seconds Mains power supply has failed or input power and/or frequency are out of tolerance Switching to battery mode automatically. When audible alarm sounding every second, battery is almost empty. Check input power source and inform dealer if necessary Warning code is shown as 09 Phase and neutral conductor at input of UPS system are reversed Rotate mains power socket by 180° or connect UPS system. Warning code is shown as 13, warning tone once a second Charger or Batteries damaged Notify dealer!! Warning code is shown as 10 Fanislockedor not working Check fans and notify dealer!! Faul
KOLFF Black 1K, -22- 8. Trouble shooting If the UPS is working abnormally, the warning or fault codes would be shown to indicate the status of UPS. Even several warnings could appear in the same time, and the warning codes would be shown circularly. Once one fault is come forth, then all previous warnings would not be shown again but only the fault code is presented. Warning and Fault Code Warning and Fault Code Bus fault 05 Site fail warning 09 Inverter fault 06 Fan fail warning 10 Overload fault 07 Bat over warning 11 Over temperature fault 08 Ba
KOLFF Black 1K, -17- The UPS does not have the backup function when it is in bypass mode. The power used by the load is supplied from the utility power via internal filter. 6.4 NO output mode The LCD display in no output mode is shown in the following diagram. The information about the utility power, the battery, the UPS output and the load could be displayed. The Bypass mode The NO output mode
KOLFF Black 1K, -1- 1. Safety and EMC instructions Please read carefully the following user manual and the safety instructions before installing the unit or using the unit! 1.1 Installation Condensation may occur if the UPS is moved directly from a cold to a warm environment. The UPS must be absolutely dry before being installed. Please allow an acclimatization time of at least two hours. Do not install the UPS near water or in damp environment. Do not install the UPS where it would be exposed to direct sunlight or near heat. Do not block ventilation open
KOLFF Black 1K, -13- finishing the self-test, the UPS will get into the inverter mode, at this time, the LCD screen will light up and indicate the state of the UPS. (2) Without utility power connecting: Even though utility power is not connected to the UPS, the UPS still can be turned on by just simply pressing “I” button continuously for more than 1 second. Then the UPS will get into self-test status first. After having finishing the self-test, the UPS will get into the inverter mode, at this time, the LCD screen will lig
-3- present before servicing! Batteries have a high short-circuit current and pose a risk of shock. Take all precautionary measures specified below and any other measures necessary when working with batteries: remove all jewellery, wristwatches, rings and other metal objects use only tools with insulated grips and handles. When changing batteries, replace with the same quantity an
KOLFF Black 1K, -15- 6. Operating mode for all models 6.1Linemode The LCD display in Line mode is shown in the following diagram. The information about the utility power, the battery, the UPS output and the load could be displayed. If output overloaded, the load percent is shown and alarm will keep twice every second. You should get rid of some unnecessary loads one by one to decrease the loads connected to the UPS less than 90% of its nominal power capacity. Note: Please follow the following steps to connect the generator Activate the generator and
KOLFF Black 1K, -16- 6.2 Battery mode The LCD display in battery mode is shown in the following diagram. The information about the utility power, the battery, the UPS output and the load could be displayed. (1) When the UPS is running in battery mode, the buzzer beeps once every 4 seconds. If the “ON” button on the front panel is pressed for more than 1 second again, the buzzer will stop beeping (in silence mode). Press the “ON” button once again for more than 1 second to resume the alarm function. (2) The display is the same in battery test mode. 6.3 Bypass mode The LCD display in bypass mode is shown in the following diagram. The information about the utility power, t
Tripp Lite OmniSmart UPS Owner's manual
OmniSmart |
Tripp Lite BC Personal UPS Owner's manual
BC Personal |
CyberPower PR3000 UPS Operation & user’s manual
PR3000 |
HP D2D UPS Manual
D2D |
Liebert NX UPS Operation & user’s manual
NX |
HP Laserjet,Color Laserjet 4550 UPS Supplementary manual
Laserjet,Color Laserjet 4550 |
Eaton 9E6Ki UPS Operation & user’s manual
9E6Ki |
Liebert 208V UPS Operation & user’s manual
208V |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | HP | StorageWorks 6100 - Enterprise Virtual Array | Operation & user’s manual | hp/storageworks-6100-enterprise-virtual-array-VP4.pdf | 05 Dec 2023 | 362 | 11.3 Mb |
2 | Marantz | SR4600 | Specifications | marantz/sr4600-C4E.pdf | 20 Dec 2023 | 2 | |
3 | Speco | CVC646HR | Specification sheet | speco/cvc646hr-P52.pdf | 25 Mar 2023 | 1 | 0.15 Mb |
4 | Panasonic | NR-B32F X 3 | Operating instructions manual | panasonic/nr-b32f-x-3-A53.pdf | 08 Jan 2023 | 20 | 7.45 Mb |
5 | Directed Electronics | Intelliguard 850 | Installation manual | directed-electronics/intelliguard-850-O75.pdf | 29 Jun 2022 | 51 | 0.59 Mb |
6 | Lenovo | ThinkPad 10 | Operation & user’s manual | lenovo/thinkpad-10-H9M.pdf | 05 Dec 2022 | 102 |
Tripp Lite
Tripp Lite1111 West 35th StreetChicago, IL 60609 USATelephone: +(773) 869 1234E-mail: [email protected] #: RBC11AUPS Replacement Battery Cartridge Kit (2 sets of 2) for select APC UPS HighlightsUp to 30% longer runtime than basic replacementsOEM certified premium batteriesRugged, leakproof constructionMaintenance-freeWide operating temperature ra …
RBC11A(2 pages) |
TSi Power
LIMITED WARRANTYTSi Power warrants this product to be free from defects in materials andworkmanship for two (2) years† from the date of purchase from TSi Power or itsauthorized representatives. TSi Power will repair (or at its option, replace) anydefective component(s) during this warranty period.To make a request or claim for service under this limited w …
UPS-400(2 pages) |
EPYC
600/800 Standby UPS with APFC support User Manual Before to start using the UPS please read carefully this manual, so to ensure the best usage and the maximum life duration of the machine. The main features of this Uninterruptible Power Supply (UPS) are listed below: Microprocessor control that guarantees high reliability � …
ION 600(4 pages) |
Xtreme
www.xpcc.com | © 2013 Xtreme Power Conversion Corporation. All rights reserved. UNINTERRUPTIBLE POWER SUPPLY (UPS) R90 Online UPS 20kVA Model USER & INSTALLATION MANUAL
…
20kVA(62 pages) |
Phasak
ON-LINE RACK PH 9360 PH 9301 LEA AL MENOS ESTO Siga estrictamente todas las advertencias e instrucciones de este manual. Antes de instalar esta unidad, lea todas las instrucciones atentamente. No utilice este SAI antes de leer atentamente toda la información de seguridad y las instrucciones de uso. …
PH 9360(100 pages) |
HP
HP D2D NASIntegration with CommVault Simpana® 9AbstractThis guide provides step by step instructions on how to configure and optimize CommVault Simpana 9 in order to back up toHP StorageWorks D2D devices using a CIFS backup target.HP Part Number: EH985-90934Published: February 2011Edition: 1
…
D2D(52 pages) |
Biostar Desktop EDEQ 4000Biostar EDEQ 4000 Desktop Operation & user’s manual EDEQ 4000, 50 |
Makita Drill M6000Instruction manual for Makita M6000 Drill M6000, 32 |
Delta Sander 31-260XDelta 31-260X Sander Instruction manual 31-260X, 60 |
Fisher-Price Motorized Toy Car N9231Fisher-Price Motorized Toy Car Instruction sheet (File: fisher-price-n9231-operation-user-s-manual-4, Saturday 20-01-2024) N9231, 4 |
Yashica Camcorder Super-600 ElectroYashica Camcorder Super-600 Electro Instruction booklet Super-600 Electro, 25 |
NARDA Measuring Instruments SRM-3006NARDA SRM-3006 Guide (Doc Type: Measuring Instruments Manual ) SRM-3006, 24 |
Brother Printer DCP-9040CNPrinter PDF Service manual DCP-9040CN, 450 |
GE Telephone Trimline 16258160GE Trimline 16258160 Guide (Operation & user’s manual), @59T82Y Trimline 16258160, 2 |
SOUNDMASTER Portable Radio TR150SWPortable Radio #G7I837 TR150SW, 3 |
Brother All in One Printer DCP-8085DNBrother All in One Printer Quick setup manual (File: brother-dcp-8085dn-quick-setup-manual-22, 25th Oct 2023) DCP-8085DN, 22 |
Sigma Other 669Guide: Sigma 669 (77763X, Upd.Friday 19-01-2024) 669, 1 |
Acer Projector X1230PKX1230PK (Projector ePDF Guide, #856D41) X1230PK, 57 |