Manualios.com

MakerBot Manuals

Manualios contain more than 46 MakerBot User Guides for 17 models of devices.

Top User Guides by MakerBot:

  • MakerBot 3D Printers

    Replicator Z18

    Quick start manual (2 pages)

    SUPPORTThe expert MakerBot Support team is standing by to help you out with any issues you may encounter while using your MakerBot Replicator Z18.e [email protected] 1.347.334.6800MakerBot Support is available Monday through Saturday 9am - 6pm EST.The MakerBot Replicator Z18 is covered by a Limited Warranty. For terms and conditions, see makerbot …

  • MakerBot 3D Printers

    Replicator 2x

    Replacement instructions (5 pages)

    Replicator 2X Bar Mount Replacement InstructionsThese are instructions for replacing the bar mount assembly for the MakerBot Replicator 2X's dual extruders. They will require the use of the 2.5 mm hex wrench that came with your printer, a pair of scissors, some tape, and possibly a small flathead screwdriver. Before you begin, do the following: • Unlo …

  • MakerBot 3D Printers

    Replicator 2 Extruder

    How-to (5 pages)

    How to Replace the Bar Mount Assembly on a MakerBot Replicator 2 ExtruderThese are instructions for replacing the bar mount assembly in a MakerBot Replicator 2 extruder. They will require the use of the 2.5 mm hex wrench that came with your bot, a pair of scissors, and, depending on your individual Replicator 2, a small flathead screwdriver. Before you begin …

  • MakerBot 3D Printers

    Replicator 2

    Replacement instructions (3 pages)

    MakerBot Replicator 2 Thermocouple Replacement InstructionsBefore you begin, do the following: • Unload any filament.• Turn off the MakerBot Replicator 2.• Remove the filament guide tube and spool holder.• Unplug power and USB cables.1. Detach the active cooling duct.Gently pull the active cooling duct away from the nozzle. Allow the duct to hang. 2. …

  • MakerBot 3D Printers

    Replicator

    Quick start manual (2 pages)

    ACCESSORY CHECKLIST1Power cord1USB A-to-B cable1 1Large MakerBot® PLA Filament spoolWELCOME. LET’S GET YOU PRINTING.GETTING TO KNOW THE CONTROL PANELMAKERBOT DESKTOP SUPPORTDOWNLOAD THE USER MANUALThe expert MakerBot Support team is standing by to help you out with any issues you may encounter while using your MakerBot Replicator. e [email protected]

  • MakerBot 3D Printers

    Thing-O-Matic

    Quick start manual (31 pages)

    10/24/12 2:04 PMMakerbot Thing-O-Matic Quick Start GuideIMPORTANT: Depending on where you are located in the world, you may need to switch the voltagesetting on you power supply. You should make sure it is in the correct position before turning your machineon. It will most likely arrive in the 110V position. Change it accordingly.Look over your Thing-O-Matic …

  • MakerBot 3D Printers

    Replicator Mini+

    Teardown manual (7 pages)

    1MakerBot Replicator Mini+ Teardown GuideMakerBotTools Needed:1.3mm Hex DriverT10 - T20 Torx Driver2.0mm Hex Driver1.5mm Hex Driver2.5 mm Hex DriverPair of thin TweezersSmall Container for ScrewsColor Guide:Button Heads ScrewActionThread Forming ScrewSocket Cap ScrewFlat Head Screw …

  • MakerBot 3D Printers

    Replicator Mini+

    Quick start manual (2 pages)

    QUICK START GUIDE1 CHECK BOX CONTENTSUSB A-to-B cableSmall MakerBot PLA Filament spoolMakerBot® Replicator® Smart Extruder+Power cord2 SET UP USING OUR APPSEE REVERSE SIDE FOR OFFLINE SETUPMake sure to read all safety information before operating your 3D printer.SUPPORTVisit our Support page for troubleshooting guides and advanced information. support.m …